An official website of the United States government
Fiber attrition of long glass fiber-reinforced polypropylene in a Couette Flow was studied to obtain a fundamental understanding of the physics in fiber breakage. The developed experimental setup of the Couette rheometer in combination with the developed fiber length measurement technique is able to provide repeatable, accurate and robust data sets to quantify the fiber length reduction during the processing of fiber-filled materials. This article summarizes the first results of an ongoing experimental study on fiber breakage at the Polymer Engineering Center at the University of Wisconsin- Madison. The impact of fiber concentration, initial fiber length, residence time, melt temperature and processing speed was quantified and studied. The proposed procedure aims to isolate the effect of process variables on fiber breakage. Even for the gentlest processing conditions, the results indicate that the residual fiber length after processing is less than 50% of the initial fiber length. For the most severe processing conditions, the results suggest a reduction to less than 10% of the initial fiber length, which highlights the challenges that fiber breakage poses for processing of long glass fiber-reinforced thermoplastics.
more »
« less
A novel fiber length measurement technique for discontinuous fiber-reinforced composites: A comparative study with existing methods
The residual fiber length in a molded part is one of the most important microstructural properties of discontinuous fiber‐reinforced composites. While there have been several research studies characterizing the process‐induced fiber length reduction, the measurement procedures vary substantially, calling into question the comparability of reported results. This article introduces a newly developed measurement procedure that aims to provide accurate, repeatable, robust, and time efficient fiber length analyses. A comprehensive study of measurement techniques was performed comparing commercially available systems and the conventional approach of measuring the fiber length manually. The results emphasize the need for a standardized procedure to characterize the fiber length distribution and the risk of generating inadequate results through improper sample preparation. The developed measurement technique was tested and compared for an experimental study of fiber breakage in injection molding. For a simple plaque geometry, the residual fiber length along the flow path was obtained for a long glass fiber‐reinforced polypropylene at 30 and 40%wt for varying process conditions. The new measurement technique showed accurate and repeatable results. The results of the injection molding study showed that screw speed and back pressure are important factors that drive fiber breakage. An increase in back pressure from 13 to 50 bar and screw speed from 27 to 35 rpm reduces the weight‐average fiber length by 37.5%.
more »
« less
- Award ID(s):
- 1633967
- PAR ID:
- 10063466
- Date Published:
- Journal Name:
- Polymer Composites
- ISSN:
- 0272-8397
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Direct particle models are a promising tool for predicting microstructural properties of fiber reinforced composites. In order to validate our modeling approach for fiber orientation prediction, compression molded reinforced Polypropylene samples were subjected to a simple shear flow in a Sliding Plate Rheometer. Micro computed tomography was used to measure the orientation tensor for deformations up to 60 shear strain units. The fully characterized microstructure at zero shear strain was used to reproduce the initial conditions in the particle simulation. Fibers were placed in a periodic boundary cell and a flow field matching the experiment was applied. Samples created with the proposed compression molding technique showed repeatable and controlled initial orientation. The model showed good agreement with the steady state orientation; however, it showed a faster orientation evolution at the start of the shearing process.more » « less
-
Carbas, Ricardo JC (Ed.)Low fiber-direction compressive strength is a well-recognized weakness of carbon fiber-reinforced polymer (CFRP) composites. When a CFRP is produced using 3D printing, the compressive strength is further degraded. To solve this issue, in this paper, a novel magnetic compaction force-assisted additive manufacturing (MCFA-AM) method is used to print CFRP laminates reinforced with carbon nanofiber (CNF) z-threads (i.e., ZT-CFRP). MCFA-AM utilizes a magnetic force to simultaneously levitate, deposit, and compact fast-curing CFRP prepregs in free space and quickly solidifies the CFRP laminate part without any mold nor supporting substrate plate; it effectively reduces the voids. The longitudinal compressive test was performed on five different sample types. ZT-CFRP/MCFA-AM samples were printed under two different magnetic compaction rolling pressures, i.e., 0.5 bar and 0.78 bar. Compared with the longitudinal compressive strength of a typical CFRP manufactured by the traditional out-of-autoclave–vacuum-bag-only (OOA-VBO) molding process at the steady-state pressure of 0.82 bar, the ZT-CFRP/MCFA-AM samples showed either comparable results (by −1.00% difference) or enhanced results (+7.42% improvement) by using 0.5 bar or 0.78 bar magnetic rolling pressures, respectively.more » « less
-
null (Ed.)Abstract Pellet-based extrusion deposition of carbon fiber-reinforced composites at high material deposition rates has recently gained much attention due to its applications in large-scale additive manufacturing. The mechanical and physical properties of large-volume components largely depend on their reinforcing fiber length. However, very few studies have been done thus far to have a direct comparison of additively fabricated composites reinforced with different carbon fiber lengths. In this study, a new additive manufacturing (AM) approach to fabricate long fiber-reinforced polymer (LFRP) was first proposed. A pellet-based extrusion deposition method was implemented, which directly used thermoplastic pellets and continuous fiber tows as feedstock materials. Discontinuous long carbon fibers, with an average fiber length of 20.1 mm, were successfully incorporated into printed LFRP samples. The printed LFRP samples were compared with short fiber-reinforced polymer (SFRP) and continuous fiber-reinforced polymer (CFRP) counterparts through mechanical tests and microstructural analyses. The carbon fiber dispersion, distribution of carbon fiber length and orientation, and fiber wetting were studied. As expected, a steady increase in flexural strength was observed with increasing fiber length. The carbon fibers were highly oriented along the printing direction. A more uniformly distributed discontinuous fiber reinforcement was found within printed SFRP and LFRP samples. Due to decreased fiber impregnation time and lowered impregnation rate, the printed CFRP samples showed a lower degree of impregnation and worse fiber wetting conditions. The feasibility of the proposed AM methods was further demonstrated by fabricating large-volume components with complex geometries.more » « less
-
This study compared the mechanical properties of a recyclable flax fiber reinforced polymer composite (FFRP) with a covalent adaptable network (CAN) matrix to an FFRP composite with a conventional (unrecyclable) epoxy resin matrix. The results indicated that composites fabricated via vacuum-assisted resin transfer molding (VARTM) exhibited up to 19% higher tensile modulus and strength compared to those fabricated via hand layup, attributed to reduced air void content and more uniform fiber alignment. Microscopy evidence supported by mechanical property tests revealed superior adhesion of the CAN matrix to flax fibers compared to conventional epoxy resin. Additionally, a solvent-based method was demonstrated for separating fibers from the CAN matrix, facilitating reuse or upcycling.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1002/pc.24466
