Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


Title: Mordant inspired wet-spinning of graphene fibers for high performance flexible supercapacitors
Recently, graphene fibers derived from wet-spinning of graphene oxide (GO) dispersions have emerged as viable electrodes for fiber-shaped supercapacitors (FSCs) and/or batteries, wherein large surface area, high electrical conductivity, and sufficient mechanical strength/toughness are desired. However, for most fiber electrodes reported so far, compromises have to be made between energy-storage capacity and mechanical/electrical performance, whereas a graphene fiber with high capacity and sufficient toughness for direct machine weaving or knitting is yet to be developed. Inspired by the alum mordant used for natural dyes in the traditional textile dyeing industry, our research group has synthesized wet-spun GO fibers and coagulated them with different multivalent cations ( e.g. Ca 2+ , Fe 3+ , and Al 3+ ), where dramatically different fiber morphologies and properties have been observed. The first principles density functional theory has been further employed to explain the observed disparities via cation–GO binding energy calculation. When assembled into solid-state FSCs, Al 3+ -based reduced GO (rGO) fibers offer excellent stability against bending, and a specific capacitance of 148.5 mF cm −2 at 40 mV s −1 , 1.4, 4.8, and 6.8 times higher than that of the rGO fibers based on other three coagulation systems (Fe 3+ , Ca 2+ and acetic acid), respectively. The volumetric energy density of the Al 3+ -based FSC is up to 13.26 mW h cm −3 , while a high power density of 250.87 mW cm −3 is maintained.  more » « less
Award ID(s):
1804534
PAR ID:
10108760
Author(s) / Creator(s):
; ; ; ; ; ;
Date Published:
Journal Name:
Journal of Materials Chemistry A
Volume:
7
Issue:
12
ISSN:
2050-7488
Page Range / eLocation ID:
6869 to 6876
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; ; (, Nanoscale)
    Titanium carbide/reduced graphene oxide (Ti 3 C 2 T z /rGO) gels were prepared by a one-step hydrothermal process. The gels show a highly porous structure with a surface area of ∼224 m 2 g −1 and average pore diameter of ∼3.6 nm. The content of GO and Ti 3 C 2 T z nanosheets in the reaction precursor was varied to yield different microstructures. The supercapacitor performance of Ti 3 C 2 T z /rGO gels varied significantly with composition. Specific capacitance initially increased with increasing Ti 3 C 2 T z content, but at high Ti 3 C 2 T z content gels cannot be formed. Also, the retention of capacitance decreased with increasing Ti 3 C 2 T z content. Ti 3 C 2 T z /rGO gel electrodes exhibit enhanced supercapacitor properties with high potential window (1.5 V) and large specific capacitance (920 F g −1 ) in comparison to pure rGO and Ti 3 C 2 T z . The synergistic effect of EDLC from rGO and redox capacitance from Ti 3 C 2 T z was the reason for the enhanced supercapacitor performance. A symmetric two-electrode supercapacitor cell was constructed with Ti 3 C 2 T z /rGO, which showed very high areal capacitance (158 mF cm −2 ), large energy density (∼31.5 μW h cm −2 corresponding to a power density of ∼370 μW cm −2 ), and long stability (∼93% retention) after 10 000 cycles. 
    more » « less
  2. ; ; ; (, RSC Advances)
    Advances in the synthesis and processing of graphene-based materials have presented the opportunity to design novel lithium-ion battery (LIB) anode materials that can meet the power requirements of next-generation power devices. In this work, a poly(methacrylic acid) (PMAA)-induced self-assembly process was used to design super-mesoporous Fe 3 O 4 and reduced-graphene-oxide (Fe 3 O 4 @RGO) anode materials. We demonstrate the relationship between the media pH and Fe 3 O 4 @RGO nanostructure, in terms of dispersion state of PMAA-stabilized Fe 3 O 4 @GO sheets at different surrounding pH values, and porosity of the resulted Fe 3 O 4 @RGO anode. The anode shows a high surface area of 338.8 m 2 g −1 with a large amount of 10–40 nm mesopores, which facilitates the kinetics of Li-ions and electrons, and improves electrode durability. As a result, Fe 3 O 4 @RGO delivers high specific-charge capacities of 740 mA h g −1 to 200 mA h g −1 at various current densities of 0.5 A g −1 to 10 A g −1 , and an excellent capacity-retention capability even after long-term charge–discharge cycles. The PMAA-induced assembly method addresses the issue of poor dispersion of Fe 3 O 4 -coated graphene materials—which is a major impediment in the synthesis process—and provides a facile synthetic pathway for depositing Fe 3 O 4 and other metal oxide nanoparticles on highly porous RGO. 
    more » « less
  3. ; (, The Journal of Engineering)
    Using a syringe pump setup, the authors conducted water flow experiments through porous reduced graphene oxide (rGO). A variety of anions and cations were added to the water to study its effect on energy harvesting. More specifically, the authors performed tests to study effect of: (1) ion concentration in water, (2) type of anion used, (3) type of cation used, and (4) effect of flow rate. The test data indicates that water flow through rGO networks can directly induce drift of charge carriers in graphene and thus generate electricity. Graphene is ideally suited for this application, since it possesses high mobility charge carriers that are ready to be coupled to moving ions present in the flowing fluid. The proposed rGO material could enable harvesting of the ubiquitous, abundant, and renewable mechanical energy of moving water directly to electrical energy. Unlike traditional schemes, the graphene material directly converts the flow energy into electrical energy without the need for moving parts. Such graphene coatings could potentially replace conventional batteries (which are environmentally hazardous) in low‐power, low‐voltage, and long service‐life applications. Once scaled up, this concept offers a potentially transformative approach to energy harvesting, as opposed to incremental advances in current technologies. 
    more » « less
  4. ; ; ; ; ; ; ; ; ; ; et al (, Journal of Materials Chemistry A)
    Hierarchically porous electrodes made of electrochemically active materials and conductive additives may display synergistic effects originating from the interactions between the constituent phases, and this approach has been adopted for optimizing the performances of many electrode materials. Here we report our findings in design, fabrication, and characterization of a hierarchically porous hybrid electrode composed of α-NiS nanorods decorated on reduced graphene oxide (rGO) (denoted as R-NiS/rGO), derived from water-refluxed metal–organic frameworks/rGO (Ni-MOF-74/rGO) templates. Microanalyses reveal that the as-synthesized α-NiS nanorods have abundant (101) and (110) surfaces on the edges, which exhibit a strong affinity for OH − in KOH electrolyte, as confirmed by density functional theory-based calculations. The results suggest that the MOF-derived α-NiS nanorods with highly exposed active surfaces are favorable for fast redox reactions in a basic electrolyte. Besides, the presence of rGO in the hybrid electrode greatly enhances the electronic conductivity, providing efficient current collection for fast energy storage. Indeed, when tested in a supercapacitor with a three-electrode configuration in 2 M KOH electrolyte, the R-NiS/rGO hybrid electrode exhibits a capacity of 744 C g −1 at 1 A g −1 and 600 C g −1 at 50 A g −1 , indicating remarkable rate performance, while maintaining more than 89% of the initial capacity after 20 000 cycles. Moreover, when coupled with a nitrogen-doped graphene aerogel (C/NG-A) negative electrode, the hybrid supercapacitor (R-NiS/rGO/electrolyte/C/NG-A) achieved an ultra-high energy density of 93 W h kg −1 at a power density of 962 W kg −1 , while still retaining an energy density of 54 W h kg −1 at an elevated working power of 46 034 W kg −1 . 
    more » « less
  5. ; ; ; ; ; ; (, ACS Applied Nano Materials)
    Expected to become mainstream in the electronic industry, flexible electronics still face major challenging issues. For polymeric based flexible electronic substrates in particular, these challenges include a lack of electromagnetic shielding capability and poor heat dissipation. Here, we report a highly flexible and thermally-conductive macroscopic polydimethylsiloxane (PDMS) polymer film embedded with copper-coated reduced graphene oxide (rGO) fiber meshes. rGO fibers are assembled into 3D fiber meshes and electroplated with micrometer-thick copper coatings, displaying excellent electrical and thermal conductivities. Oriented in the horizontal and perpendicular directions within the PDMS polymeric matrix, the fiber mesh severs as a highly electrically and thermally-conductive backbone through the in-plane direction. Meanwhile, the fiber mesh also effectively shields electromagnetic interference in the X-band without causing thermal damage. The macroscopic film maintains electrically-insulated in the through-plane direction. Utilizing both the favorable thermal and electrical properties of the graphene fiber-based mesh and the flexibility of the PDMS matrix, our film may exhibit potentials for flexible electronics applications such as wearable electronics thermal management and flexible microwave identification devices. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Text Encoded Conversion
  • XML
  • Save / Share this Record
  • Send to Email