An official website of the United States government
We examine the stretching behavior of rubber–plastic composites composed of a layer of styrene–ethylene/propylene–styrene (SEPS) rubber, bonded to a layer of linear low density polyethylene (LLDPE) plastic. Dog-bone shaped samples of rubber, plastic, and rubber–plastic bilayers with rubber : plastic thickness ratio in the range of 1.2–9 were subjected to uniaxial tension tests. The degree of inhomogeneity of deformation was quantified by digital image correlation analysis of video recordings of these tests. In tension, the SEPS layer showed homogeneous deformation, whereas the LLDPE layer showed necking followed by stable drawing owing to its elastoplastic deformation behavior and post-yield strain hardening. Bilayer laminates showed behavior intermediate between the plastic and the rubber, with the degree of necking and drawing reducing as the rubber : plastic ratio increased. A simple model was developed in which the force in the bilayer was taken as the sum of forces in the plastic and the rubber layers measured independently. By applying a mechanical energy balance to this model, the changes in bilayer necking behavior with rubber thickness could be predicted qualitatively.
more »
« less
A computational study of necking and drawing of plastic-rubber laminates
Semi-crystalline plastics undergo necking followed by stable drawing under tensile forces. In contrast, a rubber extends many times its original length uniformly under tension. Previously we have shown experimentally that the behavior of rubber-plastic composites in tension is intermediate between that of the rubber. Here we conduct finite element simulations of plastic-rubber-plastic trilayers laminates under tension. Using relatively simple constitutive equations for the rubber and the plastic, we examine how the composite mechanics changes as the ratio of rubber to plastic thickness is varied. We show that at small rubber thickness, the composites show necking, whereas beyond a certain rubber thickness, necking is completely eliminated.
more »
« less
- Award ID(s):
- 1636064
- PAR ID:
- 10109510
- Date Published:
- Journal Name:
- Annual technical conference and exhibition - Society of Plastics Engineers
- ISSN:
- 0733-4192
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Amorphous/crystalline high-entropy-alloy (HEA) composites show great promise as structural materials due to their exceptional mechanical properties. However, there is still a lack of understanding of the dynamic nanoindentation response of HEA composites at the atomic scale. Here, the mechanical behavior of amorphous/crystalline HEA composites under nanoindentation is investigated through a large-scale molecular dynamics simulation and a dislocation-based strength model, in terms of the indentation force, microstructural evolution, stress distribution, shear strain distribution, and surface topography. The results show that the uneven distribution of elements within the crystal leads to a strong heterogeneity of the surface tension during elastic deformation. The severe mismatch of the amorphous/crystalline interface combined with the rapid accumulation of elastic deformation energy causes a significant number of dislocation-based plastic deformation behaviors. The presence of surrounding dislocations inhibits the free slip of dislocations below the indenter, while the amorphous layer prevents the movement or disappearance of dislocations towards the substrate. A thin amorphous layer leads to great indentation force, and causes inconsistent stacking and movement patterns of surface atoms, resulting in local bulges and depressions at the macroscopic level. The increasing thickness of the amorphous layer hinders the extension of shear bands towards the lower part of the substrate. These findings shed light on the mechanical properties of amorphous/crystalline HEA composites and offer insights for the design of high-performance materials.more » « less
-
Solid‐state welding of Al 1043 sheets is achieved via high‐pressure torsion (HPT) processing to produce bulk nanostructured Al disks. A homogeneous nanostructure without segregation is observed, with grain sizes of ≈430–470 nm. Miniature tensile testing, coupled with the digital image correlation (DIC) technique, is employed to determine the room‐temperature tensile deformation behavior, particularly the nonuniform behavior with necking, of the HPT‐bonded ultrafine‐grained (UFG) aluminum, comparing it with annealed coarse‐grained counterpart. The HPT‐bonded UFG Al exhibits a large fraction of post‐necking strain, which is supported by the estimated high strain rate sensitivity value ofm = 0.085, suggesting the delay of local necking leading to tensile fracture. Detailed DIC analysis reveals prolonged diffuse necking, thus delaying local necking, in the HPT‐bonded UFG Al, while the annealed samples show high fractions of local necking during the nonuniform deformation. Moreover, the DIC data illustrate that local necking predominantly occurred at a limited neck zone, maintaining a plateau strain distribution at the out‐of‐neck zone throughout necking deformation toward tensile failure for both annealed and UFG aluminum. The DIC method offers an alternative means to demonstrate the transition in necking behaviors of materials by estimating the plastic lateral contraction exponent.more » « less
-
A mussel-inspired mechanism was used to solve the problem of filler aggregation in rubber composites. This research aims to improve carbon black (CB) dispersion in epoxidized natural rubber (ENR) composites through π−π stacking and cation−π interactions by adding dopamine (D). In this study, various aromatic interactions (π−π stacking and cation−π interactions) between the D-functionalized ENR molecules and the surface of the CB were observed by Fourier transform infrared (FTIR) and Raman spectroscopy. Notably, the small and wideangle X-ray scattering (SAXS/WAXS) analyses supported our inference from the rubber processing analysis (RPA) and transmission electron microscopy (TEM) results that the aromatic interactions enhanced the CB dispersion in ENR composites. This phenomenon improved the tensile strength (138%), Young’s modulus (93%), and energy-saving properties (50%). Finally, this research provided an alternative strategy using mussel-inspired material to solve the CB aggregation problem in rubber products, yielding ENR composites with superior performance properties.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Conference Paper:
- The DOI is not currently available.
