We consider a molecular junction immersed in a solvent where the electron transfer is dominated by Marcus-type steps. However, the successive nature of the charge transfer through the junction does not imply that the solvent reaches thermal equilibrium throughout the transport. In our previous work [Kirchberg et al., J. Phys. Chem. Lett. 11, 1729 (2020)], we have determined the nonequilibrium distribution of the solvent where its dynamics, expressed by a friction, is considered in two limiting regimes of fast and slow solvent relaxation. In dependence of the nonequilibrium solvent dynamics, we investigate now the electrical, thermal, and thermoelectric properties of the molecular junction. We show that by suitable tuning of the friction, we can reduce the heat dissipation into the solvent and enhance the heat transfer between the electrodes. Interestingly, we find that the Seebeck coefficient grows significantly by adapting the solvent friction in both regimes.
Hydrogels consist of a cross-linked polymer matrix imbibed with a solvent such as water at volume fractions that can exceed 90%. They are important in many scientific and engineering applications due to their tunable physiochemical properties, biocompatibility, and ultralow friction. Their multiphase structure leads to a complex interfacial rheology, yet a detailed, microscopic understanding of hydrogel friction is still emerging. Using a custom-built tribometer, here we identify three distinct regimes of frictional behavior for polyacrylic acid (PAA), polyacrylamide (PAAm), and agarose hydrogel spheres on smooth surfaces. We find that at low velocities, friction is controlled by hydrodynamic flow through the porous hydrogel network and is inversely proportional to the characteristic pore size. At high velocities, a mesoscopic, lubricating liquid film forms between the gel and surface that obeys elastohydrodynamic theory. Between these regimes, the frictional force decreases by an order of magnitude and displays slow relaxation over several minutes. Our results can be interpreted as an interfacial shear thinning of the polymers with an increasing relaxation time due to the confinement of entanglements. This transition can be tuned by varying the solvent salt concentration, solvent viscosity, and sliding geometry at the interface.
more » « less- NSF-PAR ID:
- 10149872
- Publisher / Repository:
- Proceedings of the National Academy of Sciences
- Date Published:
- Journal Name:
- Proceedings of the National Academy of Sciences
- Volume:
- 117
- Issue:
- 21
- ISSN:
- 0027-8424
- Page Range / eLocation ID:
- p. 11247-11256
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
-
null (Ed.)Since their inception, hydrogels have gained popularity among multiple fields, most significantly in biomedical research and industry. Due to their resemblance to biological tribosystems, a significant amount of research has been conducted on hydrogels to elucidate biolubrication mechanisms and their possible applications as replacement materials. This review is focused on lubrication mechanisms and covers friction models that have attempted to quantify the complex frictional characteristics of hydrogels. From models developed on the basis of polymer physics to the concept of hydration lubrication, assumptions and conditions for their applicability are discussed. Based on previous models and our own experimental findings, we propose the viscous-adhesive model for hydrogel friction. This model accounts for the effects of confinement of the polymer network provided by a solid surface and poroelastic relaxation as well as the (non) Newtonian shear of a complex fluid on the frictional force and quantifies the frictional response of hydrogels-solid interfaces. Finally, the review delineates potential areas of future research based on the current knowledge.more » « less
-
more » « less
Abstract The ability to modulate polyacrylamide hydrogel surface morphology, rheological properties, adhesion and frictional response is demonstrated by combining acrylic acid copolymerization and network confinement via grafting to a surface. Specifically, atomic force microscopy imaging reveals both micellar and lamellar microphase separations in grafted copolymer hydrogels. Bulk characterization is conducted to reveal the mechanisms underlying microstructural changes and ordering of the polymer network, supporting that they stem from the balance between hydrogen bonding in the substrate‐grafted hydrogels, electrostatic interactions, and a decrease in osmotically active charges. The morphological modulation has direct impacts on the spatial distribution of surface stiffness and adhesion. Furthermore, lateral force measurements show that the microphase separations lead to speed and load‐dependent lubrication regimes as well as spatial variation of friction. A proof of concept via salt screening demonstrates the dynamic control of surface morphology and adhesion. This work advances the knowledge necessary to design complex hydrogel interfaces that enable spatial and dynamic control of surface morphology and thereby of friction and adhesion through modulation of hydrogel composition and surface confinement, which is of significance for applications in biomedical devices, soft tissue design, soft robotics, and other engineered tribosystems.
-
more » « less
Nearly, all dense suspensions undergo dramatic and abrupt thickening transitions in their flow behavior when sheared at high stresses. Such transitions occur when the dominant interactions between the suspended particles shift from hydrodynamic to frictional. Here, we interpret abrupt shear thickening as a precursor to a rigidity transition and give a complete theory of the viscosity in terms of a universal crossover scaling function from the frictionless jamming point to a rigidity transition associated with friction, anisotropy, and shear. Strikingly, we find experimentally that for two different systems—cornstarch in glycerol and silica spheres in glycerol—the viscosity can be collapsed onto a single universal curve over a wide range of stresses and volume fractions. The collapse reveals two separate scaling regimes due to a crossover between frictionless isotropic jamming and frictional shear jamming, with different critical exponents. The material-specific behavior due to the microscale particle interactions is incorporated into a scaling variable governing the proximity to shear jamming, that depends on both stress and volume fraction. This reformulation opens the door to importing the vast theoretical machinery developed to understand equilibrium critical phenomena to elucidate fundamental physical aspects of the shear thickening transition.
-
more » « less
Abstract Establishing a constitutive law for fault friction is a crucial objective of earthquake science. However, the complex frictional behavior of natural and synthetic gouges in laboratory experiments eludes explanations. Here, we present a constitutive framework that elucidates the rate, state, and temperature dependence of fault friction under the relevant sliding velocities and temperatures of the brittle lithosphere during seismic cycles. The competition between healing mechanisms, such as viscoelastic collapse, pressure‐solution creep, and crack sealing, explains the low‐temperature stability transition from steady‐state velocity‐strengthening to velocity‐weakening as a function of slip‐rate and temperature. In addition, capturing the transition from cataclastic flow to semi‐brittle creep accounts for the stabilization of fault slip at elevated temperatures. We calibrate the model using extensive laboratory data on synthetic albite and granite gouge, and on natural samples from the Alpine Fault and the Mugi Mélange in the Shimanto accretionary complex in Japan. The constitutive model consistently explains the evolving frictional response of fault gouge from room temperature to 600°C for sliding velocities ranging from nanometers to millimeters per second. The frictional response of faults can be uniquely determined by the in situ lithology and the prevailing hydrothermal conditions.
