skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


Title: Effect of Ultrasonic Vibration on Interlayer Adhesion in Fused Filament Fabrication 3D Printed ABS
One of the fundamental issues in the Fused Filament Fabrication (FFF) additive manufacturing process lies in the mechanical property anisotropy where the strength of the FFF-3D printed part in the build-direction can be significantly lower than that in other directions. The physical phenomenon that governs this issue is the coupled effect of macroscopic thermal mechanical issues associated with the thermal history of the interface, and the microscopic effect of the polymer microstructure and mass transfer across interfaces. In this study it was found that the use of 34.4 kHz ultrasonic vibrations during FFF-3D printing results in an increase of up to 10% in the interlayer adhesion in Acrylonitrile Butadiene Styrene (ABS), comparing the printing in identical thermal conditions to that in conventional FFF printing. This increase in the interlayer adhesion strength is attributed to the increase in polymer reptation due to ultrasonic vibration-induced relaxation of the polymer chains from secondary interactions in the interface regions.  more » « less
Award ID(s):
1828355
PAR ID:
10162233
Author(s) / Creator(s):
; ; ; ;
Date Published:
Journal Name:
Polymers
Volume:
11
Issue:
2
ISSN:
2073-4360
Page Range / eLocation ID:
315
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; (, Automation in construction)
    Construction 3D Printing (C3DP) with sulfur concrete holds great potential for sustainable construction on Earth and beyond. However, a key challenge is optimizing the thermal C3DP process to minimize layer deformations while enhancing interlayer adhesion for improved mechanical strength. To tackle this challenge, this paper presents a physics-based model of heat transfer within a 3D-printed sulfur concrete structure. Numerical implementations of the model are proposed for 3D and 2D structures in Cartesian coordinates. Upon calibration, the model estimates the spatiotemporal distribution of the temperature within the structure based on thermal properties, printing parameters, and environmental conditions. The model is calibrated using experimental data, where the effect of printing parameters is analyzed, and is then utilized to simulate multiple terrestrial and Martian construction scenarios. It identifies a range of printing speeds and interlayer delays that optimize extrudate properties, while also enabling automated control of the thermal C3DP process for optimal performance. 
    more » « less
  2. ; (, Progress in Additive Manufacturing)
    Print conditions for thermoplastics by filament-based material extrusion (MatEx) are commonly optimized to maximize the elastic modulus. However, these optimizations tend to ignore the impact of thermal history that depends on the specimen size and print path selection. Here, we investigate the effect of size print path (raster angle and build orientation) and print sequence on the mechanical properties of polycarbonate (PC) and polypropylene (PP). Examination of parallel and series printing of flat (XY) and stand-on (YZ) orientation of Type V specimens demonstrated that to observe statistical differences in the mechanical response that the interlayer time between printed roads should be approximately 5 s or less. The print time for a single layer in XY orientation is much longer than that for a single layer in YZ orientation, so print sequence only impacts the mechanical response in the YZ orientation. However, the specimen size and raster angle did influence the mechanical properties in XY orientation due to the differences in thermal history associated with intralayer time between adjacent roads. Moreover, all of these effects are significantly larger when printing PC than PP. These differences between PP and PC are mostly attributed to the mechanism of interface consolidation (crystallization vs. glass formation), which changes the requirements for a strong interface between roads (crystals vs. entanglements). These results illustrate how the print times dictated by the print path layout impact observed mechanical properties. This work also demonstrated that the options available in some standards developed for traditional manufacturing will change the quantitative results when applied to 3D printed parts. 
    more » « less
  3. ; ; ; ; ; (, American Society of Mechanical Engineers)
    Abstract Additive manufacturing (AM), also known as 3D printing, has significantly advanced in recent years, especially with the introduction of multifunctional 3D-printed parts. AM fabricated monolith has multiple material capabilities, thus various functionalities are well-perceived by the manufacturing communities. As an example, a traditional fused filament fabrication (FFF) 3D printer fabricates multi-material thermoplastic parts using a dual extrusion system to increase the functionality of the part including variable stiffening and gradient structures. In addition to the multiple thermoplastic feedstocks in a dual extrusion system, multifunctional AM can be achieved by embedding electronics or reinforcing fibers within the fabricated thermoplastic parts, which significantly impacts the rapid prototyping of hybrid components in manufacturing industries. State-of-the-art techniques such as coextrusion systems, ultrasonic welding tools, and thermal embedding tools have been implemented to automate the process of embedding conductive material within the 3D-printed thermoplastic substrate. The goal of this tool development effort is to embed wires within 3D 3D-printed plastic substrate. This research consisted of developing a wire embedding tool that can be integrated into an FFF desktop 3D printer to deposit conductive as well as resistive wires within the 3D-printed thermoplastic substrate. By realizing the challenges for discrete materials interaction at the interface such as nichrome wires and Acrylonitrile Butadiene Styrene (ABS) plastics and polylactic acid (PLA), the goal of this tool was to immerse wire within ABS and PLA substrate using transient swelling mechanisms under non-polar solvent. A proof-of-concept test stands with a wire feed system and the embedding wheel was first designed and manufactured using 3D printing to examine if a traditional roller-guided system, primarily used for plastic extrusion, would be sufficient for wire extrusion. The development of the integrated wire embedding tool was initiated based on the success of the proof-of-concept wire extrusion system. The design of the integrated wire embedding tool consisted of three sub-assemblies: wire delivery assembly, wire shearing assembly, and swivel assembly. The wire delivery assembly is responsible for feeding the wire towards the thermoplastic using the filament delivery system seen within FFF printers. For the wire shearing mechanism, a cutting Tungsten carbide blade in conjunction with a Nema-17 external stepper motor was used to shear the wire. For the wire embedding assembly, a custom swivel mount was fabricated with a bearing housing for a ball bearing that allowed for a 360-degree motion around the horizontal plane. A wire guide nozzle was placed through the mount to allow for the wire to be fed down into a brass embedding wheel in a tangential manner. Additionally, the solvent reservoir was mounted such that an even layer of solution was dispensed onto the thermoplastic substrate. Through this tool development effort, the aim was to develop technologies that will enable 3D printing of wire-embedded monolith for various applications including a self-heating mold of thermoset-based composite manufacturing as well as smart composites with embedded sensors. 
    more » « less
  4. ; ; ; ; (, Rapid Prototyping Journal)
    null (Ed.)
    Purpose The purpose of this study is to understand how printing parameters and subsequent annealing impacts porosity and crystallinity of 3D printed polylactic acid (PLA) and how these structural characteristics impact the printed material’s tensile strength in various build directions. Design/methodology/approach Two experimental studies were used, and samples with a flat vs upright print orientation were compared. The first experiment investigates a scan of printing parameters and annealing times and temperatures above the cold crystallization temperature ( T cc ) for PLA. The second experiment investigates annealing above and below T cc at multiple points over 12 h. Findings Annealing above T cc does not significantly impact the porosity but it does increase crystallinity. The increase in crystallinity does not contribute to an increase in strength, suggesting that co-crystallization across the weld does not occur. Atomic force microscopy (AFM) images show that weld interfaces between printed fibers are still visible after annealing above T cc , confirming the lack of co-crystallization. Annealing below T cc does not significantly impact porosity or crystallinity. However, there is an increase in tensile strength. AFM images show that annealing below T cc reduces thermal stresses that form at the interfaces during printing and slightly “heals” the as-printed interface resulting in an increase in tensile strength. Originality/value While annealing has been explored in the literature, it is unclear how it affects porosity, crystallinity and thermal stresses in fused filament fabrication PLA and how those factors contribute to mechanical properties. This study explains how co-crystallization across weld interfaces is necessary for crystallinity to increase strength and uses AFM as a technique to observe morphology at the weld. 
    more » « less
  5. ; ; ; ; (, Materials)
    Material extrusion (MEX) additive manufacturing has successfully fabricated assembly-free structures composed of different materials processed in the same manufacturing cycle. Materials with different mechanical properties can be employed for the fabrication of bio-inspired structures (i.e., stiff materials connected to soft materials), which are appealing for many fields, such as bio-medical and soft robotics. In the present paper, process parameters and 3D printing strategies are presented to improve the interfacial adhesion between carbon fiber-reinforced nylon (CFPA) and thermoplastic polyurethane (TPU), which are extruded in the same manufacturing cycle using a multi-material MEX setup. To achieve our goal, a double cantilever beam (DCB) test was used to evaluate the mode I fracture toughness. The results show that the application of a heating gun (assembled near the nozzle) provides a statistically significant increase in mean fracture toughness energy from 12.3 kJ/m2 to 33.4 kJ/m2. The underlying mechanism driving this finding was further investigated by quantifying porosity at the multi-material interface using an X-ray computed tomography (CT) system, in addition to quantifying thermal history. The results show that using both bead ironing and the hot air gun during the printing process leads to a reduction of 24% in the average void volume fraction. The findings from the DCB test and X-ray CT analysis agree well with the polymer healing theory, in which an increased thermal history led to an increased fracture toughness at the multi-material interface. Moreover, this study considers the thermal history of each printed layer to correlate the measured debonding energy with results obtained using the reptation theory. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email