An official website of the United States government
Cadmium zinc telluride selenide (CdZnTeSe) has shown great promise in reducing the cost of semiconductor nuclear detectors that can operate at room temperature without cryogenic cooling. This is due to the high yield of detector-grade materials in the CdZnTeSe crystal growth process, which can be attributed to the much smaller numbers of Te inclusions and grain boundary network in CdZnTeSe compared to other CdTe-based semiconductors such as CdZnTe. In the present work, we study the effects of surface passivation on CdZnTe detectors using a mixture of ammonium fluoride and hydrogen peroxide solution (NH4F + H2O2 + H2O). Detectors fabricated from CdZnTeSe crystals showed very good energy resolutions: 1.1% for the 662-keV gamma peak of Cs-137 by Frisch-grid detectors, and 5.9% for the 59.6-keV gamma peak of Am-241 by planar detectors. Experimental results show that the leakage current is increased immediately after passivation and then decreases as the surfaces stabilizes. The resistivity of the CdZnTeSe is of the order of 10**10 Ω-cm. The surface passivation improved the energy resolution of planar detector by 18% for the 59.6-keV gamma peak of Am-241.
more »
« less
Ammonium Fluoride Passivation of CdZnTeSe Sensors for Applications in Nuclear Detection and Medical Imaging
Cadmium zinc telluride selenide (Cd1−xZnxTe1−ySey or CZTS) is one of the emerging CdTe-based semiconductor materials for detecting X- and gamma-ray radiation at or near room temperature (i.e., without cryogenic cooling). Potential applications of CZTS sensors include medical imaging, X-ray detection, and gamma-ray spectroscopy. Chemical passivation of CZTS is needed to reduce the conductivity of Te-rich surfaces, which reduces the noise and improves the device performance. In this study, we focus on the effect of surface passivation of CZTS using a 10% aqueous solution of ammonium fluoride. The effects of the chemical treatment were studied on the leakage current, charge transport measured as the electron mobility-lifetime (µτ) product, and the spectral resolution measured as the full-width at half-maximum (FWHM) of specific peaks. After passivation, the leakage current increased and began to decrease towards pre-passivation levels. The energy resolutions were recorded for eight applied voltages between −35 V and −200 V. The results showed an average of 25% improvement in the detector’s energy resolution for the 59.6 keV gamma peak of Am-241. The electron µτ product was unchanged at 2 × 10−3 cm2/V. These results show that ammonium fluoride is effective for chemical passivation of CZTS detectors.
more »
« less
- Award ID(s):
- 1818732
- PAR ID:
- 10184942
- Date Published:
- Journal Name:
- Sensors
- Volume:
- 19
- Issue:
- 15
- ISSN:
- 1424-8220
- Page Range / eLocation ID:
- 3271
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Cadmium telluride (CdTe) and its ternary and quaternary compounds have found applications in the development of X-ray and gamma-ray detectors used in nuclear detection and medical imaging applications. Example of these detectors include CdZnTe (CZT), CdMnTe (CMT), and CdZnTeSe (CZTS). These nuclear detectors can operate at room temperature without cryogenic cooling. This paper presents comparative studies of these semiconductor material. The properties studied include detector resistivity, Te inclusions, grain boundary networks, mobility/lifetime of the charge carriers, and energy resolution. The effects of passivation with chemicals such as KOH and NH4F, are also presented. X-ray photoelectron spectroscopy (XPS) studies showed increase in the quantity of TeO2 on surfaces of these materials after passivation in KOH and NH4F. While CZT detector has wide commercial availability, it has more Te inclusions and grain boundary network compared to CZTS. CMT and CZTS have better crystal uniformity than CZT. The comparatively low presence of Te inclusions and grain boundary network in CZTS gives it a higher crystal growth yield for detector-grade material.more » « less
-
We report the electrical properties of Al0.3Ga0.7N/GaN heterojunction field effect transistor (HFET) structures with a Ga2O3 passivation layer grown by metal–organic chemical vapor deposition (MOCVD). In this study, three different thicknesses of β-Ga2O3 dielectric layers were grown on Al0.3Ga0.7N/GaN structures leading to metal-oxide-semiconductor-HFET or MOSHFET structures. X-ray diffraction (XRD) showed the (2¯01) orientation peaks of β-Ga2O3 in the device structure. The van der Pauw and Hall measurements yield the electron density of ~ 4 × 1018 cm−3 and mobility of ~770 cm2V−1s−1 in the 2-dimensional electron gas (2DEG) channel at room temperature. Capacitance–voltage (C-V) measurement for the on-state 2DEG density for the MOSHFET structure was found to be of the order of ~1.5 × 1013 cm−2. The thickness of the Ga2O3 layer was inversely related to the threshold voltage and the on-state capacitance. The interface charge density between the oxide and Al0.3Ga0.7N barrier layer was found to be of the order of ~1012 cm2eV−1. A significant reduction in leakage current from ~10−4 A/cm2 for HFET to ~10−6 A/cm2 for MOSHFET was observed well beyond pinch-off in the off-stage at -20 V applied gate voltage. The annealing at 900° C of the MOSHFET structures revealed that the Ga2O3 layer was thermally stable at high temperatures resulting in insignificant threshold voltage shifts for annealed samples with respect to as-deposited (unannealed) structures. Our results show that the MOCVD-gown Ga2O3 dielectric layers can be a strong candidate for stable high-power devices.more » « less
-
Morkoç, Hadis; Fujioka, Hiroshi; Schwarz, Ulrich T. (Ed.)We report the gate leakage current and threshold voltage characteristics of Al0.3Ga0.7N/GaN heterojunction field effect transistor (HFET) with metal-organic chemical vapor deposition (MOCVD) grown β-Ga2O3 as a gate dielectric for the first time. In this study, GaN channel HFET and β-Ga2O3 passivated metal-oxide-semiconductor-HFET (MOS-HFET) structures were grown in MOCVD using N2 as carrier gas on a sapphire substrate. X-ray diffraction (XRD) and atomic force microscopy (AFM) were used to characterize the structural properties and surface morphology of the heterostructure. The electrical properties were analyzed using van der Pauw, Hall, and the mercury probe capacitance-voltage (C-V) measurement systems. The 2-dimensional electron gas (2DEG) carrier density for the heterostructure was found to be in the order of ~1013 cm-2. The threshold voltage shifted more towards the negative side for the MOSHFET. The high-low (Hi-Lo) frequency-based C-V method was used to calculate the interface charge density for the oxide-AlGaN interface and was found to be in the order of ~1012 cm2eV-1. A remarkable reduction in leakage current from 2.33×10-2 A/cm2 for HFET to 1.03×10-8 A/cm2 for MOSHFET was observed demonstrating the viability of MOCVD-grown Ga2O3 as a gate dielectric.more » « less
-
Radiation damage mitigation in electronics remains a challenge because the only established technique, thermal annealing, does not guarantee a favorable outcome. In this study, a non-thermal annealing technique is presented, where electron momentum from very short duration and high current density pulses is used to target and mobilize the defects. The technique is demonstrated on 60 Co gamma irradiated (5 × 10 6 rad dose and 180 × 10 3 rad h −1 dose rate) GaN high electron mobility transistors. The saturation current and maximum transconductance were fully and the threshold voltage was partially recovered at 30 °C or less. In comparison, thermal annealing at 300 °C mostly worsened the post-irradiation characteristics. Raman spectroscopy showed an increase in defects that reduce the 2-dimensional electron gas (2DEG) concentration and increase the carrier scattering. Since the electron momentum force is not applicable to the polymeric surface passivation, the proposed technique could not recover the gate leakage current, but performed better than thermal annealing. The findings of this study may benefit the mitigation of some forms of radiation damage in electronics that are difficult to achieve with thermal annealing.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.3390/s19153271
