Flexible thermoelectric (TE) devices hold great promise for energy harvesting and cooling applications, with increasing significance to serve as perpetual power sources for flexible electronics and wearable devices. Despite unique and superior TE properties widely reported in nanocrystals, transforming these nanocrystals into flexible and functional forms remains a major challenge. Herein, demonstrated is a transformative 3D conformal aerosol jet printing and rapid photonic sintering process to print and sinter solution‐processed Bi2Te2.7Se0.3nanoplate inks onto virtually any flexible substrates. Within seconds of photonic sintering, the electrical conductivity of the printed film is dramatically improved from nonconductive to 2.7 × 104S m−1. The films demonstrate a room temperature power factor of 730 µW m−1K−2, which is among the highest values reported in flexible TE films. Additionally, the film shows negligible performance changes after 500 bending cycles. The highly scalable and low‐cost fabrication process paves the way for large‐scale manufacturing of flexible devices using a variety of high‐performing nanoparticle inks.
- Award ID(s):
- 2006231
- NSF-PAR ID:
- 10202980
- Date Published:
- Journal Name:
- Electronics
- Volume:
- 9
- Issue:
- 3
- ISSN:
- 2079-9292
- Page Range / eLocation ID:
- 532
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
Abstract -
more » « less
Abstract Thermoelectric generators are an environmentally friendly and reliable solid‐state energy conversion technology. Flexible and low‐cost thermoelectric generators are especially suited to power flexible electronics and sensors using body heat or other ambient heat sources. Bismuth telluride (Bi2Te3) based thermoelectric materials exhibit their best performance near room temperature making them an ideal candidate to power wearable electronics and sensors using body heat. In this report, Bi2Te3thin films are deposited on a flexible polyimide substrate using low‐cost and scalable manufacturing methods. The synthesized Bi2Te3nanocrystals have a thickness of 35 ± 15 nm and a lateral dimension of 692 ± 186 nm. Thin films fabricated from these nanocrystals exhibit a peak power factor of 0.35 mW m−1·K−2at 433 K, which is among the highest reported values for flexible thermoelectric films. In order to evaluate the flexibility of the thin films, static and dynamic bending tests are performed while monitoring the change in electrical resistivity. After 1000 bending cycles over a 50 mm radius of curvature, the change in electrical resistance of the film is 23%. Using Bi2Te3solutions, the ability to print thermoelectric thin films with an aerosol jet printer is demonstrated, highlighting the potential of additive manufacturing techniques for fabricating flexible thermoelectric generators.
-
Over the past decade, Ag 2 Se has attracted increasing attention due to its potentially excellent thermoelectric (TE) performance as an n-type semiconductor. It has been considered a promising alternative to Bi–Te alloys and other commonly used yet toxic and/or expensive TE materials. To optimize the TE performance of Ag 2 Se, recent research has focused on fabricating nanosized Ag 2 Se. However, synthesizing Ag 2 Se nanoparticles involves energy-intensive and time-consuming techniques with poor yield of final product. In this work, we report a low-cost, solution-processed approach that enables the formation of Ag 2 Se thin films from Cu 2−x Se template films via cation exchange at room temperature. Our simple two-step method involves fabricating Cu 2−x Se thin films by the thiol-amine dissolution of bulk Cu 2 Se, followed by soaking Cu 2−x Se films in AgNO 3 solution and annealing to form Ag 2 Se. We report an average power factor (PF) of 617 ± 82 μW m −1 K −2 and a corresponding ZT value of 0.35 at room temperature. We obtained a maximum PF of 825 μW m −1 K −2 and a ZT value of 0.46 at room temperature for our best-performing Ag 2 Se thin-film after soaking for 5 minutes. These high PFs have been achieved via full solution processing without hot-pressing.more » « less
-
more » « less
Sulfide solid-state electrolyte (SE) possesses high room-temperature ionic conductivity. However, fabrication of the free-standing, sheet-type thin sulfide SE film electrolyte to enable all-solid-state batteries to deliver high energy and power density remains challenging. Herein we show that argyrodite sulfide (Li6PS5Cl) SE can be slurry cast to form free-standing films with low (≤5 wt%) loadings of poly(isobutylene) (PIB) binder. Two factors contribute to a lower areal specific resistance (ASR) of the thin film SEs benchmarked to the pristine powder pellet SSE counterparts: i) 1–2 orders reduced thickness and ii) reasonably comparable ionic conductivity at room temperature after the isostatic pressing process. Nevertheless, an increasing polymer binder loading inevitably introduced voids in the thin film SEs, compromising anode/electrolyte interfacial ion transport. Our findings highlight that electrolyte/electrode interfacial stability, as well as the selection of slurry components, including sulfide SE, binder, and solvent, play essential roles in thin film sulfide electrolyte development.
-
BSE mosaics of mushes and experimental products. Abstract: "We conducted experiments to study melt migration in crystal-rich mushes, with application to magma ascent within transcrustal magma reservoirs. Mushes with crystal volume fractions of 0.59 to 0.83 were prepared by hot-pressing crushed borosilicate glass mixed with different amounts quartz sand particles. Each experimental sample comprises stacked disks of mush and soda-lime glass, a proxy for crystal-free magma. Samples were subjected to confining pressures of 100 to 300 MPa and a temperature of 900°C (above the glass transition temperatures of the borosilicate and soda-lime glasses) for up to 6 h. The bottom and circumference of the mush and soda lime disks experience the confining pressure, but the top of the mush disks are at room pressure, resulting in a pore-pressure gradient across the mush layer. Following cooling and decompression, we determined the area fraction and morphology of soda-lime melt that migrated into the mush layer during experiments. Melt fraction is more strongly correlated to crystal fraction than pore-pressure gradient, increasing with crystal fraction before sharply decreasing as crystal fractions exceed 0.8. This change at 0.8 coincides with the transition from crystals in the mush moving during soda-lime migration to crystals forming a continuous rigid network. In our experiments, melt migration occurred by viscous fingering, but near the mobile-to-rigid transition, melt migration is enhanced by additional capillary action. Our results indicate that magma migration may peak when rigid mushes “unlock” to become mobile. This transition may mark an increase in magma migration, a potential precursor to volcanic unrest and eruption." Imaging: "Transverse sections cut from the top and/or bottom of the vacuum hot-pressed mushes were polished, carbon-coated, and imaged in BSE mode using the JEOL JXA-8530FPlus Electron Probe Microanalyzer (EPMA) at UMN (15 kV, 10 nA). About ten 50x magnification images were taken per sample and then compiled into BSE mosaics using Affinity Designer. The different compositions of the borosilicate glass and crystalline materials are distinguishable by greyscale in BSE images. [...] Following each experiment, sample assemblies were cut longitudinally along the cylindrical axis to produce sections for microstructural analysis. Scored samples (pHi-19s, Int-20s, Lo-21s) were cut again to produce sections tangential to the sample cylinder. Cut sections were vacuum impregnated with EpoFix resin and hand-polished on diamond lapping film from 30 to 0.5 μm grit. Polished and carbon-coated samples were imaged in BSE mode in the EPMA at UMN (15 kV, 10 nA). The different compositions of the soda-lime glass, borosilicate glass, and crystalline materials are distinguishable by greyscale in BSE images. Twenty to forty 50x magnification images were taken per sample and then compiled into sample-scale BSE mosaics using Affinity Designer."more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.3390/electronics9030532
