skip to main content

This content will become publicly available on October 1, 2022

Title: The form-finding and fabrication of an ultra-thin funicular bridge prototype made up of hollow glass units
The recent development of three-dimensional graphic statics (3DGS) has greatly increased the ease of designing complex and efficient spatial funicular structural forms [1]. The reciprocal diagram based 3DGS approaches not only generate highly efficient funicular structures [2], but also result in planarity constraints due to the polyhedron nature of the reciprocal diagrams [3]. Our previous research has shown the feasibility of leveraging this planarity by using planar glass sheets to materialize the 10m-span, double-layer glass bridge [3]. This paper is framed as a proof of concept for the 10m bridge and explores the form-finding, detail configuration, fabrication constraints, and assembly logic by designing and constructing a small-scale bridge prototype with a span of 2.5m. The prototype is designed in a modular approach, where each polyhedral cell of the form is materialized using a hollow glass unit (HGU) (Figure 1a), which can be prefabricated and preassembled, and therefore, greatly simplifies the assembly of the whole bridge. The compression-only form of the prototype is generated using the PolyFrame beta [4] plug-in for Rhinoceros [5]. The form-finding is carried out with a comprehensive consideration of a variety of parameters, including fabrication constraints, assembly ease, construction cost, and practicality. To start the form-finding process, a more » group of closed convex force polyhedrons is aggregated, controlling the topology of the form diagram and the orientations of the form elements. By manipulating the face tilting angles of the force diagram, the supported edges at the end of the bridge are all made horizontal, reducing the difficulty of the support design. Then, vertex locations and edge lengths of the form diagram are constrained, determining the final dimensions of both the bridge and the cells. After getting the geometry of the bridge, the detail developments are streamlined. Each of the 13 HGUs consists of two flat deck plates and a series of side plates (Figure 1b). To interlock the adjacent cells and prevent possible sliding, a male-female connection mechanism is introduced to the conjoint side plates of the HGUs (Figure 1b). Additionally, to eliminate the direct contact of the glass parts and prevent the stress concentration, two softer transparent materials are involved for connecting purposes. Within each HGU, silicon-based binding agent is used to hold the glass parts together; between the neighboring HGUs, plastic sheets are placed as interface materials (Figure 1b). Figure 1. a) The 2.5m-span small-scale prototype dome, b) Exploded view showing deck plates, side plates, male-female connection, and interface material For the fabrication of the glass parts, 5-axis Waterjet cutting techniques are applied. While the glass sheets for the deck plates can be purchased from the market, the irregular side plates with male-female connections need to be made from kiln-cast glass. In terms of the Waterjet cutting constraints, there is a max cutting angle of 60 degrees from vertical. With respect to this, all the glass parts are examined during the design process to ensure they all satisfy the cutting angle requirements. Aiming to achieve a fast and precise assembly, several assistant techniques are developed. On the local HGU level, assembly connectors are designed and 3D-printed to help locate the glass parts. On the global prototype level, the assembly sequence of the HGUs are simulated to avoid interference. Besides, a labeling system is also established to organize the fabricated parts and guide the entire assembly process. The design and construction of this small-scale prototype provide important information for the future development of the full-scale bridge regarding the interlocking detail design, the fabrication constraints, and assembly logic. The actual structural performance of the prototype awaits further investigation through-loading experiments. « less
Authors:
; ; ; ; ; ; ;
Award ID(s):
1944691
Publication Date:
NSF-PAR ID:
10209887
Journal Name:
International Association of Shell and Spatial Structures
Sponsoring Org:
National Science Foundation
More Like this
  1. The recent development of three-dimensional graphic statics using polyhedral reciprocal diagrams (PGS) has greatly increased the ease of designing complex yet efficient spatial funicular structural forms, where the inherent planarity of the polyhedral geometries can be harnessed for efficient construction processes. Our previous research has shown the feasibility of leveraging this planarity in materializing a 10m-span, double-layer glass bridge made of 1cm glass sheets. This paper presents a smaller bridge prototype with a span of 2.5m to address the larger bridge’s challenges regarding form-finding, detail developments, fabrication constraints, and assembly logic. The compression-only prototype is designed for prefabrication as amore »modular system using PolyFrame for Rhinoceros. Thirteen polyhedral cells of the funicular bridge are materialized in the form of hollow glass units (HGUs) and can be prefabricated and assembled on-site. Each HGU consists of two deck plates and multiple side plates held together using 3M™ Very High Bond (VHB) tape. A male-female glass connection mechanism is developed at the sides of HGUs to interlock each unit with its adjacent cells to prevent sliding. A transparent interface material is placed between the male and female connecting parts to avoid local stress concentration. This novel construction method significantly simplifies the bridge’s assembly on a large scale. The design and construction of this small-scale prototype set the foundation for the future development of the full-scale structure.« less
  2. This research presents an experimental program executed to understand the strength and stiffness properties of hollow built-up glass compression members that are intended for use in the modular construction of all glass, compression-dominant, shell-type structures. The proposed compression-dominant geometric form has been developed using the methods of form finding and three-dimensional graphical statics. This research takes the first steps towards a new construction methodology for glass structures where individual hollow glass units (HGU) are assembled using an interlocking system to form large, compression-dominant, shell-type structures, thereby exploiting the high compression strength of glass. In this study, an individual HGU hasmore »an elongated hexagonal prism shape and consists of two deck plates, two long side plates, and four short side plates, as is shown in Figure 1. Connections between glass plates are made using a two-sided transparent structural adhesive tape. The test matrix includes four HGUs, two each fabricated with 1 mm and 2 mm thick adhesive tape. All samples are dimensioned 64 cm on the long axis of symmetry, 51 cm on the short axis of symmetry, and are 10 cm in width. Glass plates are all 10 mm thick annealed float glass with geometric fabrication done using 5-axis abrasive water jet cutting. HGU assembly is accomplished using 3D printed truing clips and results in a rigid three-dimensional glass frame. Testing was done with the HGU oriented such that load was introduced on the short side edges of the two deck plates, resulting in an asymmetric load-support condition. A soft interface material was used between the HGU and steel plates of the hydraulic actuator and support for the purpose of avoiding premature cracking from local stress concentrations on the glass edges at the load and support locations. Force was applied in displacement control at 0.25 mm/minute with a full array of displacement and strain sensors. Test results for load vs. center deck plate transverse deflection are shown in Figure 2. All samples failed explosively by flexural buckling with no premature cracking on the load and support edges of the deck plates. Strain and deformation data clearly show the presence of second-order behavior resulting from bending deformation perpendicular to the plane of the deck plates. In general, linear axial behavior transitions to nonlinear second-order behavior, with increasing rates in deflection and strain growth, ultimately ending in glass fracture on the tension surfaces of the buckled deck plates. The failure resulted in near-complete disintegration of the deck plates, but with no observable cracking in any side plates and a secure connection on all adhesive tape. Results of the experimental program clearly demonstrate the feasibility of using HGUs for modular construction of compression dominant all-glass shell-type structures. This method of construction can significantly reduce the self-weight of the structure, and it will inspire the use of sustainable materials in the construction of efficient structures.« less
  3. In this experimental research a transparent thermoplastic manufactured by the DOW Corporation and known as Surlyn is investigated for use as an interface material in fabrication of an all-glass pedestrian bridge. The bridge is modular in construction and fabricated from a series of interlocking hollow glass units (HGU) that are geometrically arranged to form a compression dominant structural system. Surlyn is used as a friction-based interface between neighbouring HGUs preventing direct glass-to-glass contact. An experimental program consisting of axial loading of short glass columns (SGC) sandwiched between Surlyn sheets is used to quantify the bearing capacity at which glass fracturemore »occurs at the glass-Surlyn interface location. Applied load cases include 100,000 cycles of cyclic load followed by 12 hours of sustained load followed by monotonic load to cracking, and monotonic loading to cracking with no previous load history. Test results show that Surlyn functions as an effective interface material with glass fracture occurring at bearing stress levels in excess of the column-action capacity of an individual HGU. Furthermore, load cycling and creep loading had no effect on the glass fracture capacity. However, the load history had a nominal effect on Surlyn, increasing stiffness and reducing deformation.« less
  4. Abstract Origami-based fabrication strategies open the door for developing new manufacturing processes capable of producing complex three-dimensional (3D) geometries from two-dimensional (2D) sheets. Nevertheless, for these methods to translate into scalable manufacturing processes, rapid techniques for creating controlled folds are needed. In this work, we propose a new approach for controlled self-folding of shape memory polymer sheets based on direct laser rastering. We demonstrate that rapidly moving a CO2 laser over pre-strained polystyrene sheets results in creating controlled folds along the laser path. Laser interaction with the polymer induces localized heating above the glass transition temperature with a temperature gradientmore »across the thickness of the thin sheets. This gradient of temperature results in a gradient of shrinkage owing to the viscoelastic relaxation of the polymer, favoring folding toward the hotter side (toward the laser source). We study the influence of laser power, rastering speed, fluence, and the number of passes on the fold angle. Moreover, we investigate process parameters that produce the highest quality folds with minimal undesired deformations. Our results show that we can create clean folds up to and exceeding 90 deg, which highlights the potential of our approach for creating lightweight 3D geometries with smooth surface finishes that are challenging to create using 3D printing methods. Hence, laser-induced self-folding of polymers is an inherently mass-customizable approach to manufacturing, especially when combined with cutting for integration of origami and kirigami.« less
  5. Modern fabrication methods have greatly simplified manufacturing of complex free-form shapes at an affordable cost, and opened up new possibilities for improving functionality and customization through automatic optimization, shape optimization in particular. However, most existing shape optimization methods focus on single parts. In this work, we focus on supporting shape optimization for assemblies, more specifically, assemblies that are held together by contact and friction. Examples of which include furniture joints, construction set assemblies, certain types of prosthetic devices and many other. To enable this optimization, we present a framework supporting robust and accurate optimization of a number of important functionals,more »while enforcing constraints essential for assembly functionality: weight, stress, difficulty of putting the assembly together, and how reliably it stays together. Our framework is based on smoothed formulation of elasticity equations with contact, analytically derived shape derivatives, and robust remeshing to enable large changes of shape, and at the same time, maintain accuracy. We demonstrate the improvements it can achieve for a number of computational and experimental examples.« less