An official website of the United States government
SUMMARY Low-temperature plastic rheology of calcite plays a significant role in the dynamics of Earth's crust. However, it is technically challenging to study plastic rheology at low temperatures because of the high confining pressures required to inhibit fracturing. Micromechanical tests, such as nanoindentation and micropillar compression, can provide insight into plastic rheology under these conditions because, due to the small scale, plastic deformation can be achieved at low temperatures without the need for secondary confinement. In this study, nanoindentation and micropillar compression experiments were performed on oriented grains within a polycrystalline sample of Carrara marble at temperatures ranging from 23 to 175 °C, using a nanoindenter. Indentation hardness is acquired directly from nanoindentation experiments. These data are then used to calculate yield stress as a function of temperature using numerical approaches that model the stress state under the indenter. Indentation data are complemented by uniaxial micropillar compression experiments. Cylindrical micropillars ∼1 and ∼3 μm in diameter were fabricated using a focused ion beam-based micromachining technique. Yield stress in micropillar experiments is determined directly from the applied load and micropillar dimensions. Mechanical data are fit to constitutive flow laws for low-temperature plasticity and compared to extrapolations of similar flow laws from high-temperature experiments. This study also considered the effects of crystallographic orientation on yield stress in calcite. Although there is a clear orientation dependence to plastic yielding, this effect is relatively small in comparison to the influence of temperature.
more »
« less
Atomic-scale homogeneous plastic flow beyond near-theoretical yield stress in a metallic glass
Abstract The onset of yielding and the related atomic-scale plastic flow behavior of bulk metallic glasses at room temperature have not been fully understood due to the difficulty in performing the atomic-scale plastic deformation experiments needed to gain direct insight into the underlying fundamental deformation mechanisms. Here we overcome these limitations by combining a unique sample preparation method with atomic force microscopy-based indentation, which allows study of the yield stress, onset of yielding, and atomic-scale plastic flow of a platinum-based bulk metallic glass in volumes containing as little as approximately 1000 atoms. Yield stresses markedly higher than in conventional nanoindentation testing were observed, surpassing predictions from current models that relate yield stress to tested volumes; subsequent flow was then established to be homogeneous without exhibiting collective shear localization or loading rate dependence. Overall, variations in glass properties due to fluctuations of free volume are found to be much smaller than previously suggested.
more »
« less
- Award ID(s):
- 1901959
- PAR ID:
- 10215316
- Publisher / Repository:
- Nature Publishing Group
- Date Published:
- Journal Name:
- Communications Materials
- Volume:
- 2
- Issue:
- 1
- ISSN:
- 2662-4443
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Serrations in the stress-time curve for a bulk metallic glass composite with microscale crystalline precipitates were measured with exceptionally high temporal resolution and low noise. Similar measurements were made for a more brittle metallic glass that did not contain crystallites but that was also tested in uniaxial compression. Despite significant differences in the structure and stress-strain behavior, the statistics of the serrations for both materials follow a simple mean-field model that describes plastic deformation as arising from avalanches of slipping weak spots. The presence of the crystalline precipitates reduces the number of large slips relative to the number of small slips as recorded in the stress-time data, consistent with the model predictions. The results agree with mean-field predictions for a smaller weakening parameter for the composite than for the monolithic metallic glass; the weakening parameter accounts for the underlying microstructural differences between the two.more » « less
-
Two distinct types of slip events occur during serrated plastic flow of bulk metallic glasses. These events are distinguished not only by their size but also by distinct stress drop rate profiles. Small stress drop serrations have fluctuating stress drop rates (with maximum stress drop rates ranging from 0.3–1 GPa/s), indicating progressive or intermittent propagation of a shear band. The large stress drop serrations are characterized by sharply peaked stress drop rate profiles (with maximum stress drop rates of 1–100 GPa/s). The propagation of a large slip is preceded by a slowly rising stress drop rate that is presumably due to the percolation of slipping weak spots prior to the initiation of shear over the entire shear plane. The onset of the rapid shear event is accompanied by a burst of acoustic emission. These large slips correspond to simultaneous shear with uniform sliding as confirmed by direct high-speed imaging and image correlation. Both small and large slip events occur throughout plastic deformation. The significant differences between these two types require that they be carefully distinguished in both modeling and experimental efforts.more » « less
-
Molecular processes of creep in metallic glass thin films are simulated at experimental timescales using a metadynamics-based atomistic method. Space–time evolutions of the atomic strains and nonaffine atom displacements are analyzed to reveal details of the atomic-level deformation and flow processes of amorphous creep in response to stress and thermal activations. From the simulation results, resolved spatially on the nanoscale and temporally over time increments of fractions of a second, we derive a mechanistic explanation of the well-known variation of creep rate with stress. We also construct a deformation map delineating the predominant regimes of diffusional creep at low stress and high temperature and deformational creep at high stress. Our findings validate the relevance of two original models of the mechanisms of amorphous plasticity: one focusing on atomic diffusion via free volume and the other focusing on stress-induced shear deformation. These processes are found to be nonlinearly coupled through dynamically heterogeneous fluctuations that characterize the slow dynamics of systems out of equilibrium.more » « less
-
Abstract Different semicrystalline polymers including poly(l‐lactic acid), poly(ethylene terephthalate), syndiotactic polystyrene, and polyamide 12 are studied in terms of their mechanical response to uniaxial compression deformation. Apparent decoupling of yielding of amorphous and crystalline phases is identified as separate peaks in the stress–strain curve in the vicinity of the glass transition temperature. The same feature is also observed for the uniaxial extension of predrawn semicrystalline poly(ethylene terephthalate). It is indicated that in absence of a strong amorphous phase a semicrystalline polymer is unable to yield and undergo plastic deformation and it fails in a brittle manner in the uniaxial compression. Treating a semicrystalline polymer as a composite of amorphous and crystalline phases, putting emphasis on the crucial role of amorphous phase in acting as connectors between crystalline domains and indicating that the yielding of amorphous phase is a prerequisite for yielding of crystalline phase, work toward a better understanding of the mechanical properties of semicrystalline polymers at the molecular level is done.more » « less
