A vast amount of experimental and analytical research has been conducted related to the seismic behavior and performance of concrete filled steel tubular (CFT) columns. This research has resulted in a wealth of information on the component behavior. However, analytical and experimental data for structural systems with CFT columns is limited, and the well known behavior of steel or concrete structures is assumed valid for designing these systems. This paper presents the development of an analytical model for nonlinear analysis of composite moment resisting frame (CFT MRF) systems with CFT columns and steel wide flange (WF) beams under seismic loading. The model integrates component models for steel WF beams, CFT columns, connections between CFT columns and WF beams, and CFT panel zones. These component models account for nonlinear behavior due to steel yielding and local buckling in the beams and columns, concrete cracking and crushing in the columns, and yielding of panel zones and connections. Component tests were used to validate the component models. The model for a CFT MRF considers second order geometric effects from the gravity load bearing system using a lean on column. The experimental results from the testing of a four story CFT MRF test structure are used as a benchmark to validate the modeling procedure. An analytical model of the test structure was created using the modeling procedure and imposed
displacement analyses were used to reproduce the tests with the analytical model of the test structure. Good agreement was found at the global and local level. The model reproduced reasonably well the story shear story drift response as well as the column, beam and connection moment rotation response, but overpredicted the inelastic deformation of the panel zone.
more »
« less
Laboratory and computer simulations of reinforced concrete frames with different ductility
Reinforced concrete structures that lack proper seismic detailing commonly have increased vulnerability to collapse during strong earthquake shaking. A major contributor to building collapse vulnerability is the prevalence of columns with widely spaced and poorly configured transverse reinforcement. Such columns are susceptible to shear failures, which can lead to axial failures and local or global building collapse. This study presents a laboratory test program that was designed to gain insight into the effects of column detailing on the dynamic response including collapse of concrete frames. Twelve concrete frames were tested on a shaking table and were subjected to two types of ground motions: one relatively short‐duration motion with strong velocity pulse and one relatively long‐duration motion with multiple cycles. The study also evaluates the effectiveness of modern analytical methods to simulate the nonlinear dynamic response of concrete structures. Two lumped plasticity models employing nonlinear rotational and shear springs at the column ends were used to simulate the collapse response of the tested specimens.
The study demonstrates that modern analytical techniques can simulate reliably the nonlinear dynamic response of concrete structures in the post‐yielding stage and can identify the onset of shear failure and collapse of concrete frames. However, in the majority of cases, the analytical models overestimated the effects of damage accumulation, especially for long‐duration motions. Response predictions were improved by adjusting the damage modeling parameters. Copyright © 2016 John Wiley & Sons, Ltd.
more » « less- NSF-PAR ID:
- 10237914
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Earthquake Engineering & Structural Dynamics
- Volume:
- 45
- Issue:
- 10
- ISSN:
- 0098-8847
- Page Range / eLocation ID:
- p. 1603-1619
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
more » « less
Summary A methodology is introduced to assess the post‐earthquake structural safety of damaged buildings using a quantitative relationship between observable structural component damage and the change in collapse vulnerability. The proposed framework integrates component‐level damage simulation, virtual inspection, and structural collapse performance assessment. Engineering demand parameters from nonlinear response history analyses are used in conjunction with component‐level damage simulation to generate multiple realizations of damage to key structural elements. Triggering damage state ratios, which describe the fraction of components within a damage state that results in an unsafe placard assignment, are explicitly linked to the increased collapse vulnerability of the damaged building. A case study is presented in which the framework is applied to a 4‐story reinforced concrete frame building with masonry infills. The results show that when subjected to maximum considered earthquake level ground motions, the probability of experiencing enough structural damage to trigger an unsafe placard, leading to building closure, is more than 2 orders of magnitude higher than the risk of collapse.
-
null (Ed.)Abstract The Mw 7.1 47 km deep earthquake that occurred on 30 November 2018 had deep societal impacts across southcentral Alaska and exhibited phenomena of broad scientific interest. We document observations that point to future directions of research and hazard mitigation. The rupture mechanism, aftershocks, and deformation of the mainshock are consistent with extension inside the Pacific plate near the down‐dip limit of flat‐slab subduction. Peak ground motions >25%g were observed across more than 8000 km2, though the most violent near‐fault shaking was avoided because the hypocenter was nearly 50 km below the surface. The ground motions show substantial variation, highlighting the influence of regional geology and near‐surface soil conditions. Aftershock activity was vigorous with roughly 300 felt events in the first six months, including two dozen aftershocks exceeding M 4.5. Broad subsidence of up to 5 cm across the region is consistent with the rupture mechanism. The passage of seismic waves and possibly the coseismic subsidence mobilized ground waters, resulting in temporary increases in stream flow. Although there were many failures of natural slopes and soils, the shaking was insufficient to reactivate many of the failures observed during the 1964 M 9.2 earthquake. This is explained by the much shorter duration of shaking as well as the lower amplitude long‐period motions in 2018. The majority of observed soil failures were in anthropogenically placed fill soils. Structural damage is attributed to both the failure of these emplaced soils as well as to the ground motion, which shows some spatial correlation to damage. However, the paucity of instrumental ground‐motion recordings outside of downtown Anchorage makes these comparisons challenging. The earthquake demonstrated the challenge of issuing tsunami warnings in complex coastal geographies and highlights the need for a targeted tsunami hazard evaluation of the region. The event also demonstrates the challenge of estimating the probabilistic hazard posed by intraslab earthquakes.more » « less
-
more » « less
Abstract Seismic design of water retaining structures relies heavily on the response of the retained water to shaking. The water dynamic response has been evaluated by means of analytical, numerical, and experimental approaches. In practice, it is common to use simplified code‐based methods to evaluate the added demands imposed by water sloshing. Yet, such methods were developed with an inherent set of assumptions that might limit their application. Alternatively, numerical modeling methods offer a more accurate way of quantifying the water response and have been commonly validated using 1 g shake table experiments. In this study, a unique series of five centrifuge tests was conducted with the goal of investigating the hydrodynamic behavior of water by varying its height and length. Moreover, sine wave and earthquake motions were applied to examine the water response at different types and levels of excitation. Arbitrary Lagrangian‐Eulerian finite element models were then developed to reproduce 1 g shake table experiments available in the literature in addition to the centrifuge tests conducted in this study. The results of the numerical simulations as well as the simplified and analytical methods were compared to the experimental measurements, in terms of free surface elevation and hydrodynamic pressures, to evaluate their applicability and limitations. The comparison showed that the numerical models were able to reasonably capture the water response of all configurations both under earthquake and sine wave motions. The analytical solutions performed well except for cases with resonance under harmonic motions. As for the simplified methods, they provided acceptable results for the peak responses under earthquake motions. However, under sine wave motions, where convective sloshing is significant, they underpredict the response. Also, beyond peak ground accelerations of 0.5 g., a mild nonlinear increase in peak dynamic pressures was measured which deviates from assumed linear response in the simplified methods. The study confirmed the reliability of numerical models in capturing water dynamic responses, demonstrating their broad applicability for use in complex problems of fluid‐structure‐soil interaction.
-
Steel moment-resisting frames (MRFs) are widely used in the United States to resist seismic forces. MRFs have many advantages, including high ductility, architectural versatility, and vetted member and connection detailing requirements. However, MRFs require large members to meet story drift criteria. Moreover, strong-column-weak-beam requirements can result in significant member sizes, and – even in the cases where strong-column-weak-beam requirements are satisfied – MRFs can still be vulnerable to story mechanisms in one or a few stories. Recently, the concept of a strongback has been utilized successfully to delay or prevent story mechanism behavior in braced frames. The strongback is represented by a steel truss or column that is designed to remain essentially elastic, thus allowing the system to transfer inelastic demands across stories. Although systems including strongbacks exhibit more uniform story drift demands with building height and reduced peak drift response, the elastic nature of the strongback can also result in near-elastic higher-mode force demands. This study compares the dynamic response of a baseline MRF to that of a retrofit using a strongback column. Several ground motions are considered to determine which cases produce the largest drift, acceleration, and force demands.more » « less
