skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


Title: Understanding wear behavior of 3D-Printed calcium phosphate-reinforced CoCrMo in biologically relevant media
Recent advances in the processing of wear-resistant calcium-phosphate reinforced CoCrMo composites for articulating surface applications has necessitated further investigation of performance in biological conditions relevant to patient applications. To this end, CoCrMo composites containing calcium phosphate in the form of hydroxyapatite (HA) were manufactured to study the influence of the reinforcing phase on the tribofilm formation in biologically-relevant conditions. The CoCrMo-HA composites were processed using a laser engineered net shaping (LENS™) additive manufacturing (AM) system with three distinctive compositions: CoCrMo-0%HA, CoCrMo-1%HA, and CoCrMo-3%HA. Extensive wear testing of the CoCrMo-HA composites was carried out in DMEM (cell media) and DMEM + Hyaluronic acid (found naturally in synovial fluid). Wear tests were performed at loads ranging from 5N to 20N, and wear media was measured post-test using ICP-MS techniques for the release of Co and Cr ions. During testing, all coefficients of friction remained in the 0.15-0.25 range, which was lower than the previously reported 0.50-0.75 range in DI water, indicating that the DMEM + hyaluronic acid media plays a significant role in reducing frictional contact. At loads higher than 15N, the HA-tribofilm exhibited a breakdown resulting in higher wear rates but still lower overall ion release in comparison to the CoCrMo control composition. Our results indicate that CoCrMo alloys with HA addition can significantly reduce wear rates and ion release even in the presence of naturally-occurring synovial-fluid friction-reducing constituents.  more » « less
Award ID(s):
1934230
PAR ID:
10282740
Author(s) / Creator(s):
; ;
Date Published:
Journal Name:
Journal of mechanical behavior of biomedical materials
Volume:
120
ISSN:
1878-0180
Page Range / eLocation ID:
104564
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; ; ; (, Journal of Orthopaedic Research)
    Abstract Articular joints facilitate motion and transfer loads to underlying bone through a combination of cartilage tissue and synovial fluid, which together generate a low‐friction contact surface. Traumatic injury delivered to cartilage and the surrounding joint capsule causes secretion of proinflammatory cytokines by chondrocytes and the synovium, triggering cartilage matrix breakdown and impairing the ability of synovial fluid to lubricate the joint. Once these inflammatory processes become chronic, posttraumatic osteoarthritis (PTOA) development begins. However, the exact mechanism by which negative alterations to synovial fluid leads to PTOA pathogenesis is not fully understood. We hypothesize that removing the lubricating macromolecules from synovial fluid alters the relationship between mechanical loads and subsequent chondrocyte behavior in injured cartilage. To test this hypothesis, we utilized an ex vivo model of PTOA that involves subjecting cartilage explants to a single rapid impact followed by continuous articulation within a lubricating bath of either healthy synovial fluid, phosphate‐buffered saline (PBS), synovial fluid treated with hyaluronidase, or synovial fluid treated with trypsin. These treatments degrade the main macromolecules attributed with providing synovial fluid with its lubricating properties; hyaluronic acid and lubricin. Explants were then bisected and fluorescently stained to assess global and depth‐dependent cell death, caspase activity, and mitochondrial depolarization. Explants were tested via confocal elastography to determine the local shear strain profile generated in each lubricant. These results show that degrading hyaluronic acid or lubricin in synovial fluid significantly increases middle zone chondrocyte damage and shear strain loading magnitudes, while also altering chondrocyte sensitivity to loading. 
    more » « less
  2. ; ; ; (, Acta biomaterialia)
    null (Ed.)
    Titanium has been used in various biomedical applications; however, titanium exhibits poor wear resistance, and its bioinert surface slows osseointegration in vivo. In this study, directed energy deposition (DED)-based additive manufacturing (AM) was used to process hydroxyapatite (HA) reinforced Ti6Al4V (Ti64) composites to improve biocompatibility and wear resistance simultaneously. Electron micrographs of the composites revealed dense microstructures where HA is observed at the β-phase grain boundaries. Hardness was observed to increase by 57% and 71% for 2 and 3 wt.% HA in Ti64 composites, respectively. XRD analysis revealed no change in the present phases. Tribological studies revealed an increase in contact resistance due to in situ HA-based tribofilm formation, reduction in wear rate when testing in DMEM with a ZrO2 counter wear ball, ˂1% wear ball volume loss, and suppression of cohesive failure of the Ti matrix. Histomorphometric analysis from a rat distal femur study revealed an increase in the osteoid surface over the bone surface (OS/BS) for 3 wt.% HA composite over the control Ti64 from 9 ± 1% to 14 ± 1%. Shear modulus was also observed to increase from 17 ± 3 MPa for control Ti64 to 32 ± 5 MPa for the 3 wt.% HA composite after 5 weeks. Our study demonstrates that the addition of HA in Ti64 can simultaneously improve bone tissue-implant response and wear resistance. 
    more » « less
  3. ; ; ; ; ; (, Biointerphases)
    Interactions between molecules in the synovial fluid and the cartilage surface may play a vital role in the formation of adsorbed films that contribute to the low friction of cartilage boundary lubrication. Osteoarthritis (OA) is the most common degenerative joint disease. Previous studies have shown that in OA-diseased joints, hyaluronan (HA) not only breaks down resulting in a much lower molecular weight (MW), but also its concentration is reduced ten times. Here, we have investigated the structural changes of lipid-HA complexes as a function of HA concentration and MW to simulate the physiologically relevant conditions that exist in healthy and diseased joints. Small angle neutron scattering and dynamic light scattering were used to determine the structure of HA-lipid vesicles in bulk solution, while a combination of atomic force microscopy and quartz crystal microbalance was applied to study their assembly on a gold surface. We infer a significant influence of both MW and HA concentrations on the structure of HA-lipid complexes in bulk and assembled on a gold surface. Our results suggest that low MW HA cannot form an amorphous layer on the gold surface, which is expected to negatively impact the mechanical integrity and longevity of the boundary layer and could contribute to the increased wear of the cartilage that has been reported in joints diseased with OA. 
    more » « less
  4. ; ; ; ; ; ; ; ; ; (, Applied Materials Today)
    Synovial joints, critical for limb biomechanics, rely on sophisticated lubrication systems to minimize wear. Disruptions, whether from injury or disease, often necessitate joint replacements. While additive manufacturing offers personalized implants, ensuring wear resistance remains a challenge. This study delves into the potential of Ti3C2Tx and Mo2TiC2Tx nanosheets in mitigating wear of additively manufactured cobalt-chromium tungsten alloy substrates when incorporated as additives into synovial fluid. The colloidal solutions demonstrate an excellent stability, a crucial factor for reproducible assays and potential clinical applicability. Analysis of contact angles and surface tensions reveals MXene-induced alterations in substrate wettability, while maintaining their general hydrophilic character. Viscosity analysis indicates that MXene addition reduces the dynamic viscosity, particularly at higher concentrations above 5 mg/mL, thus enhancing dispersion and lubrication properties. Friction and wear tests demonstrate a dependency on the MXene concentration, while Ti3C2Tx exhibits stable friction coefficients and up to 77 % wear reduction at 5 mg/mL, which was attributed to the formation of a wear-protecting tribo-film (amorphous carbon and MXene nano-sheets). Our findings suggest that Ti3C2Tx, when supplied in favorable concentrations, holds promise for reducing wear in biotribological applications, offering avenues for future research into optimizing MXene utilization in load-bearing joint replacements and other biomedical devices. 
    more » « less
  5. ; ; ; ; ; ; ; ; ; ; et al (, Advanced Materials)
    Abstract Bottlebrush polymers (BB) have emerged as compelling candidates for biosystems to face tribological challenges, including friction and wear. This study provides a comprehensive assessment of an engineered triblock BB polymer's affinity, cell toxicity, lubrication, and wear protection in both in vitro and in vivo settings, focusing on applications for conditions like osteoarthritis and dry eye syndrome. Results show that the designed polymer rapidly adheres to various surfaces (e.g., cartilage, eye, and contact lens), forming a robust, biocompatible layer for surface lubrication and protection. The tribological performance and biocompatibility are further enhanced in the presence of hyaluronic acid (HA) both in vitro and in vivo. The exceptional lubrication performance and favorable interaction with HA position the synthesized triblock polymer as a promising candidate for innovative treatments addressing deficiencies in bio‐lubricant systems. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email