skip to main content

Explore Research Products in the NSF-PAR

Title: Water oxidation kinetics of nanoporous BiVO 4 photoanodes functionalised with nickel/iron oxyhydroxide electrocatalysts
In this work, spectroelectrochemical techniques are employed to analyse the catalytic water oxidation performance of a series of three nickel/iron oxyhydroxide electrocatalysts deposited on FTO and BiVO 4 , at neutral pH. Similar electrochemical water oxidation performance is observed for each of the FeOOH, Ni(Fe)OOH and FeOOHNiOOH electrocatalysts studied, which is found to result from a balance between degree of charge accumulation and rate of water oxidation. Once added onto BiVO 4 photoanodes, a large enhancement in the water oxidation photoelectrochemical performance is observed in comparison to the un-modified BiVO 4 . To understand the origin of this enhancement, the films were evaluated through time-resolved optical spectroscopic techniques, allowing comparisons between electrochemical and photoelectrochemical water oxidation. For all three catalysts, fast hole transfer from BiVO 4 to the catalyst is observed in the transient absorption data. Using operando photoinduced absorption measurements, we find that water oxidation is driven by oxidised states within the catalyst layer, following hole transfer from BiVO 4 . This charge transfer is correlated with a suppression of recombination losses which result in remarkably enhanced water oxidation performance relative to un-modified BiVO 4 . Moreover, despite similar electrocatalytic behaviour of all three electrocatalysts, we show that variations in water oxidation performance observed among the BiVO 4 /MOOH photoanodes stem from differences in photoelectrochemical and electrochemical charge accumulation in the catalyst layers. Under illumination, the amount of accumulated charge in the catalyst is driven by the injection of photogenerated holes from BiVO 4 , which is further affected by the recombination loss at the BiVO 4 /MOOH interface, and thus leads to deviations from their behaviour as standalone electrocatalysts.  more » « less
Award ID(s):
1764399
NSF-PAR ID:
10310635
Author(s) / Creator(s):
; ; ; ; ; ; ;
Date Published:
Journal Name:
Chemical Science
Volume:
12
Issue:
21
ISSN:
2041-6520
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; ; ; ; ; ; ; ( , Nanoscale)
    null (Ed.)
    Oxygen evolution reaction (OER) catalysts are critical components of photoanodes for photoelectrochemical (PEC) water oxidation. Herein, nanostructured metal boride MB (M = Co, Fe) electrocatalysts, which have been synthesized by a Sn/SnCl 2 redox assisted solid-state method, were integrated with WO 3 thin films to build heterojunction photoanodes. As-obtained MB modified WO 3 photoanodes exhibit enhanced charge carrier transport, amended separation of photogenerated electrons and holes, prolonged hole lifetime and increased charge carrier density. Surface modification of CoB and FeB significantly enhances the photocurrent density of WO 3 photoanodes from 0.53 to 0.83 and 0.85 mA cm −2 , respectively, in transient chronoamperometry (CA) at 1.23 V vs. RHE (V RHE ) under interrupted illumination in 0.1 M Na 2 SO 4 electrolyte (pH 7), corresponding to an increase of 1.6 relative to pristine WO 3 . In contrast, the pristine MB thin film electrodes do not produce noticeable photocurrent during water oxidation. The metal boride catalysts transform in situ to a core–shell structure with a metal boride core and a metal oxide (MO, M = Co, Fe) surface layer. When coupled to WO 3 thin films, the CoB@CoO x nanostructures exhibit a higher catalytic enhancement than corresponding pure cobalt borate (Co-B i ) and cobalt hydroxide (Co(OH) x ) electrocatalysts. Our results emphasize the role of the semiconductor–electrocatalyst interface for photoelectrodes and their high dependency on materials combination. 
    more » « less
  2. ; ; ; ; ; ; ; ; ; ; et al ( , Advanced Energy Materials)
    Abstract

    Significant optical absorption in the blue–green spectral range, high intralayer carrier mobility, and band alignment suitable for water splitting suggest tin disulfide (SnS2) as a candidate material for photo‐electrochemical applications. In this work, vertically aligned SnS2nanoflakes are synthesized directly on transparent conductive substrates using a scalable close space sublimation (CSS) method. Detailed characterization by time‐resolved terahertz and time‐resolved photoluminescence spectroscopies reveals a high intrinsic carrier mobility of 330 cm2V−1s−1and photoexcited carrier lifetimes of 1.3 ns in these nanoflakes, resulting in a long vertical diffusion length of ≈1 µm. The highest photo‐electrochemical performance is achieved by growing SnS2nanoflakes with heights that are between this diffusion length and the optical absorption depth of ≈2 µm, which balances the competing requirements of charge transport and light absorption. Moreover, the unique stepped morphology of these CSS‐grown nanoflakes improves photocurrent by exposing multiple edge sites in every nanoflake. The optimized vertical SnS2nanoflake photoanodes produce record photocurrents of 4.5 mA cm−2for oxidation of a sulfite hole scavenger and 2.6 mA cm−2for water oxidation without any hole scavenger, both at 1.23 VRHEin neutral electrolyte under simulated AM1.5G sunlight, and stable photocurrents for iodide oxidation in acidic electrolyte.

     
    more » « less
  3. ; ; ; ; ; ( , Advanced Energy Materials)
    Abstract

    Recently, a new method to effectively engineer the bandgap of barium bismuth niobate (BBNO) double perovskite was reported. However, the planar electrodes based on BBNO thin films show low photocurrent densities for water oxidation owing to their poor electrical conductivity. Here, it is reported that the photoelectrochemical (PEC) activity of BBNO‐based electrodes can be dramatically enhanced by coating thin BBNO layers on tungsten oxide (WO3) nanosheets to solve the poor conductivity issue while maintaining strong light absorption. The PEC activity of BBNO/WO3nanosheet photoanodes can be further enhanced by applying Co0.8Mn0.2Oxnanoparticles as a co‐catalyst. A photocurrent density of 6.02 mA cm−2at 1.23 V (vs reversible hydrogen electrode (RHE)) is obtained using three optically stacked, but electrically parallel, BBNO/WO3nanosheet photoanodes. The BBNO/WO3nanosheet photoanodes also exhibit excellent stability in a high‐pH alkaline solution; the photoanodes demonstrate negligible photocurrent density decay while under continuous PEC operation for more than 7 h. This work suggests a viable approach to improve the PEC performance of BBNO absorber‐based devices.

     
    more » « less
  4. ; ; ( , Advanced Energy Materials)
    Abstract

    The materials that are receiving the most attention in photoelectrochemical water splitting are metallic nanoparticle electrocatalysts (np‐EC) attached to the surface of a semiconductor (SC) light absorber. In these multicomponent systems, the interface between the semiconductor and electrocatalysts critically affects performance. However, the np‐EC/SC interface remains poorly understood as it is complex on atomic scales, dynamic under reaction conditions, and inaccessible to direct experimental probes. This contribution sheds light on how the electrocatalyst/semiconductor interface evolves under reaction conditions by investigating the behavior of nickel electrocatalysts (as nanoparticles and films) deposited on silicon semiconductors. Rigorous electrochemical experiments, interfacial atomistic characterization, and computational modeling are combined to demonstrate critical links between the atomistic features of the interface and the overall performance. It is shown that electrolyte‐induced atomistic changes to the interface lead to (1) modulation of the charge carrier fluxes and a dramatic decrease in the electron/hole recombination rates and (2) a change in the barrier height of the interface. Furthermore, the critical roles of nonidealities and electrocatalyst coverage due to interfacial geometry are explored. Each of these factors must be considered to optimize the design of metal/semiconductor interfaces which are broadly applicable to photoelectrocatalysis and photovoltaic research.

     
    more » « less
  5. ; ; ; ; ; ; ; ; ( , Chemistry – A European Journal)
    Abstract

    In this work, an organic‐inorganic hybrid crystal, violet‐crystal (VC), was used to etch the nickel foam (NF) to fabricate a self‐standing electrode for the water oxidation reaction. The efficacy of VC‐assisted etching manifests the promising electrochemical performance towards the oxygen evolution reaction (OER), requiring only ~356 and ~376 mV overpotentials to reach 50 and 100 mA cm−2, respectively. The OER activity improvement is attributed to the collectively exhaustive effects arising from the incorporation of various elements in the NF, and the enhancement of active site density. Furthermore, the self‐standing electrode is robust, exhibiting a stable OER activity after 4,000 cyclic voltammetry cycles, and ~50 h. The anodic transfer coefficients (αa) show that the first electron transfer step is the rate‐determining step on the surface of NF‐VCs‐1.0 (NF etched by 1 g of VCs) electrode, while the chemical step involving dissociation following the first electron transfer step is identified as the rate‐limiting step in other electrodes. The lowest Tafel slope value observed in the NF‐VCs‐1.0 electrode indicates the high surface coverage of oxygen intermediates and more favorable OER reaction kinetics, as confirmed by high interfacial chemical capacitance and low charge transport/interfacial resistance. This work demonstrates the importance of VCs‐assisted etching of NF to activate the OER, and the ability to predict reaction kinetics and rate‐limiting step based onαavalues, which will open new avenues to identify advanced electrocatalysts for the water oxidation reaction.

     
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email