skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


Title: Polymer–Plasticizer Coatings for BTEX Detection Using Quartz Crystal Microbalance
Sensing films based on polymer–plasticizer coatings have been developed to detect volatile organic compounds (VOCs) in the atmosphere at low concentrations (ppm) using quartz crystal microbalances (QCMs). Of particular interest in this work are the VOCs benzene, ethylbenzene, and toluene which, along with xylene, are collectively referred to as BTEX. The combinations of four glassy polymers with five plasticizers were studied as prospective sensor films for this application, with PEMA-DINCH (5%) and PEMA-DIOA (5%) demonstrating optimal performance. This work shows how the sensitivity and selectivity of a glassy polymer film for BTEX detection can be altered by adding a precise amount and type of plasticizer. To quantify the film saturation dynamics and model the absorption of BTEX analyte molecules into the bulk of the sensing film, a diffusion study was performed in which the frequency–time curve obtained via QCM was correlated with gas-phase analyte composition and the infinite dilution partition coefficients of each constituent. The model was able to quantify the respective concentrations of each analyte from binary and ternary mixtures based on the difference in response time (τ) values using a single polymer–plasticizer film as opposed to the traditional approach of using a sensor array. This work presents a set of polymer–plasticizer coatings that can be used for detecting and quantifying the BTEX in air, and discusses the selection of an optimum film based on τ, infinite dilution partition coefficients, and stability over a period of time.  more » « less
Award ID(s):
1640668
PAR ID:
10316050
Author(s) / Creator(s):
; ; ; ;
Date Published:
Journal Name:
Sensors
Volume:
21
Issue:
16
ISSN:
1424-8220
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; ; ; ; (, Atmospheric Measurement Techniques)
    Abstract. Previous studies have demonstrated volatility-dependent absorption of gas-phase volatile organic compounds (VOCs) to Teflon and other polymers. Polymer–VOC interactions are relevant for atmospheric chemistry sampling, as gas–wall partitioning in polymer tubing can cause delays and biases during measurements. They are also relevant to the study of indoor chemistry, where polymer-based materials are abundant (e.g., carpets and paints). In this work, we quantify the absorptive capacities of multiple tubing materials, including four nonconductive polymers (important for gas sampling and indoor air quality), four electrically conductive polymers and two commercial steel coatings (for gas and particle sampling). We compare their performance to previously characterized materials. To quantify the absorptive capacities, we expose the tubing to a series of ketones in the volatility range 104–109 µg m−3 and monitor transmission. For slow-diffusion polymers (e.g., perfluoroalkoxy alkane (PFA) Teflon and nylon), absorption is limited to a thin surface layer, and a single-layer absorption model can fit the data well. For fast-diffusion polymers (e.g., polyethylene and conductive silicone), a larger depth of the polymer is available for diffusion, and a multilayer absorption model is needed. The multilayer model allows fitting solid-phase diffusion coefficients for different materials, which range from 4×10-9 to 4×10-7 cm2 s−1. These diffusion coefficients are ∼ 8 orders of magnitude larger than literature values for fluorinated ethylene propylene (FEP) Teflon film. This enormous difference explains the differences in VOC absorption measured here. We fit an equivalent absorptive mass (CW, µg m−3) for each absorptive material. We found PFA to be the least absorptive, with CW ∼ 105 µg m−3, and conductive silicone to be the most absorptive, with CW ∼ 1013 µg m−3. PFA transmits VOCs easily and intermediate-volatility species (IVOCs) with quantifiable delays. In contrast, conductive silicone tubing transmits only the most volatile VOCs, denuding all lower-volatility species. Semi-volatile species (SVOCs) are very difficult to sample quantitatively through any tubing material. We demonstrate a system combining several slow- and fast-diffusion tubing materials that can be used to separate a mixture of VOCs into volatility classes. New conductive silicone tubing contaminated the gas stream with siloxanes, but this effect was reduced 10 000-fold for aged tubing, while maintaining the same absorptive properties. SilcoNert (tested in this work) and Silonite (tested in previous work) steel coatings showed gas transmission that was almost as good as PFA, but since they undergo adsorption, their delay times may be humidity- and concentration-dependent. 
    more » « less
  2. ; ; ; ; (, Journal of Polymer Science)
    Abstract We developed the dynamic assembly of the hydrogen‐bonded multilayers of (poly(N‐vinylpyrrolidone/poly(methacrylic acid)) (PVPON/PMAA)) and compared their properties to the static multilayers. We found that dynamic multilayers, wherein a planar substrate is shaken during polymer adsorption, leads to a 15‐time faster deposition of the planar coatings. The thicknesses and roughness of the dynamic coatings were found to be ⁓30% larger than those of static (no shaking) multilayer films as measured by spectroscopic ellipsometry and atomic force microscopy. We examined the film growth, mechanical properties, wettability, hydration, and pH stability of the planar static and dynamic multilayers and demonstrated that these properties were insignificantly affected by the assembly mode. Both static and dynamic coatings produced microporous films when exposed to pH = 5.9, close to the film critical dissolution pH = 6. We discovered that during the release of the multilayer films into a solution to produce free‐standing films either as planar membranes or multilayer capsule shells, the molecular chain rearrangements result in the decreased roughness for both static and dynamic multilayers and lead to a decreased thickness of the dynamic multilayers. Our findings can help develop a rapid synthesis of thicker nanostructured polymer coatings for sensing and controlled delivery applications. 
    more » « less
  3. ; ; ; (, Sensors)
    Herein, we examine two sensing schemes for detection and discrimination of chlorinated volatile organic compounds (VOCs). In this work, phosphonium ionic liquids (ILs) were synthesized and vapor sensing properties examined and compared to phosphonium IL-polymer composites. Pure IL sensors were used to develop a QCM-based multisensory array (MSA), while IL-polymer composites were used to develop an MSA and virtual sensor arrays (VSAs). It was found that by employing the composite MSA, five chlorinated VOCs were accurately discriminated at 95.56%, which was an increase in accuracy as compared to pure ILs MSA (84.45%). Data acquired with two out of three VSAs allowed discrimination of chlorinated VOCs with 100% accuracy. These studies have provided greater insight into the benefits of incorporating polymers in coating materials for enhanced discrimination accuracies of QCM-based sensor arrays. To the best of our knowledge, this is the first report of a QCM-based VSA for discrimination of closely related chlorinated VOCs. 
    more » « less
  4. ; ; ; ; ; (, Advanced Materials Technologies)
    Abstract There are advantages to polymer/nanoparticle composite‐based volatile organic compounds (VOCs) sensors, such as high chemical and physical stability, operability under extreme conditions, flexible use in manufacturing, and low cost. Nevertheless, their lower limit of detection due to thickness‐dependent diffusion has constrained their application. Inspired by the metaxylem in vascular plants and its vertical conduits and horizontal pits that enable efficient transpiration, a polymer/nanoparticle composite‐based sensor is fabricated with a controllable, spontaneously formed, hollow core for inline VOCs transportation, and porous microstructure for radial direction diffusion. The hollow core is surrounded by an inner porous layer (thermoplastic polyurethane (TPU)), a middle sensing layer (TPU/graphene nanoplatelets/multiwalled carbon nanotubes), and an outer mechanically durable layer (TPU). This multilayered structure shows a 600% higher response rate compared to a single‐layered composite fiber sensor, with a low limit of detection (e.g., ≈15 ppm for xylene) and high selectivity based on the Flory–Huggins interaction parameter. This flexible and stretchable sensor also demonstrates a dual parameter sensing capability from VOC concentrations and uniaxial strain deformation. Via a one‐step fiber spinning procedure, this self‐induced hollow fiber offers a unique method of microstructural design, which enables the detection of low‐concentration VOCs by polymer/nanoparticle‐based sensors. 
    more » « less
  5. ; ; (, Biosensors)
    Serotonin (5-HT) is a critical neurotransmitter involved in many neuronal functions, and 5-HT depletion has been linked to several mental diseases. The fast release and clearance of serotonin in the extracellular space, low analyte concentrations, and a multitude of interfering species make the detection of serotonin challenging. This work presents an electrochemical aptamer-based biosensing platform that can monitor 5-HT continuously with high sensitivity and selectivity. Our electrochemical sensor showed a response time of approximately 1 min to a step change in the serotonin concentration in continuous monitoring using a single-frequency EIS (electrochemical impedance spectroscopy) technique. The developed sensing platform was able to detect 5-HT in the range of 25–150 nM in the continuous sample fluid flow with a detection limit (LOD) of 5.6 nM. The electrochemical sensor showed promising selectivity against other species with similar chemical structures and redox potentials, including dopamine (DA), norepinephrine (NE), L-tryptophan (L-TP), 5-hydroxyindoleacetic acid (5-HIAA), and 5-hydroxytryptophan (5-HTP). The proposed sensing platform is able to achieve high selectivity in the nanomolar range continuously in real-time, demonstrating the potential for monitoring serotonin from neurons in organ-on-a-chip or brain-on-a-chip-based platforms. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email