Demineralized bone matrix (DBM) has been widely used clinically for dental, craniofacial and skeletal bone repair, as an osteoinductive and osteoconductive material. 3D printing (3DP) enables the creation of bone tissue engineering scaffolds with complex geometries and porosity. Photoreactive methacryloylated gelatin nanoparticles (GNP-MAs) 3DP inks have been developed, which display gel-like behavior for high print fidelity and are capable of post-printing photocrosslinking for control of scaffold swelling and degradation. Here, novel DBM nanoparticles (DBM-NPs, ∼400 nm) were fabricated and characterized prior to incorporation in 3DP inks. The objectives of this study were to determine how these DBM-NPs would influence the printability of composite colloidal 3DP inks, assess the impact of ultraviolet (UV) crosslinking on 3DP scaffold swelling and degradation and evaluate the osteogenic potential of DBM-NP-containing composite colloidal scaffolds. The addition of methacryloylated DBM-NPs (DBM-NP-MAs) to composite colloidal inks (100:0, 95:5 and 75:25 GNP-MA:DBM-NP-MA) did not significantly impact the rheological properties associated with printability, such as viscosity and shear recovery or photocrosslinking. UV crosslinking with a UV dosage of 3 J/cm2 directly impacted the rate of 3DP scaffold swelling for all GNP-MA:DBM-NP-MA ratios with an ∼40% greater increase in scaffold area and pore area in uncrosslinked versus photocrosslinked scaffolds over 21 days in phosphate-buffered saline (PBS). Likewise, degradation (hydrolytic and enzymatic) over 21 days for all DBM-NP-MA content groups was significantly decreased, ∼45% less in PBS and collagenase-containing PBS, in UV-crosslinked versus uncrosslinked groups. The incorporation of DBM-NP-MAs into scaffolds decreased mass loss compared to GNP-MA-only scaffolds during collagenase degradation. An in vitro osteogenic study with bone marrow-derived mesenchymal stem cells demonstrated osteoconductive properties of 3DP scaffolds for the DBM-NP-MA contents examined. The creation of photoreactive DBM-NP-MAs and their application in 3DP provide a platform for the development of ECM-derived colloidal materials and tailored control of biochemical cue presentation with broad tissue engineering applications.
- Award ID(s):
- 1847103
- NSF-PAR ID:
- 10321307
- Date Published:
- Journal Name:
- Journal of Materials Science: Materials in Medicine
- Volume:
- 32
- Issue:
- 8
- ISSN:
- 0957-4530
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
Abstract -
Abstract The macro-porous ceramics has promising durability and thermal insulation performance. As porous ceramics find more and more applications across many industries, a cost-effective and scalable additive manufacturing technique for fabricating macro-porous ceramics is highly desirable. Herein, we reported a facile additive manufacturing approach to fabricate porous ceramics and control the printed porosity. Several printable ceramic inks were prepared, and the foaming agent was added to generate gaseous bubbles in the ink, followed by the direct ink writing and the ambient-pressure and room-temperature drying to create the three-dimensional geometries. A set of experimental studies were performed to optimize the printing quality. The results revealed the optimal process parameters for printing the foamed ceramic ink with a high spatial resolution and fine surface quality. Varying the concentration of the foaming agent enables the controllability of the structural porosity. The maximum porosity can reach 85%, with a crack-free internal porous structure. The tensile tests showed that the printed macro-porous ceramics possessed enhanced durability with the addition of fiber. With a high-fidelity three-dimensional (3D) printing process and the precise controllability of the porosity, we showed that the printed samples exhibited a remarkably low thermal conductivity and durable mechanical strength.more » « less
-
more » « less
Abstract The macro-porous ceramics has promising durability and thermal insulation performances. A cost-effective and scalable additive manufacturing technique for the fabrication of macro-porous ceramics, with a facile approach to control the printed porosity is reported in the paper. Several ceramic inks were prepared, the foaming agent was used to generate gaseous bubbles in the ink, followed by the direct ink writing and the ambient-pressure and room-temperature drying to create the three-dimensional geometries. The experimental studies were performed to optimize the printing quality. A set of studies revealed the optimal printing process parameters for printing the foamed ceramic ink with a high spatial resolution and fine surface quality. Varying the concentration of the foaming agent enabled the controllability of the structural porosity. The maximum porosity can reach 85%, with a crack-free internal porous structure. The tensile tests showed that the printed macro-porous ceramics have enhanced durability with the addition of fiber. With a high-fidelity 3D printing process and precise control of the porosity, the printed samples exhibited a low thermal conductivity and high mechanical strength.
-
more » « less
Human bone demonstrates superior mechanical properties due to its sophisticated hierarchical architecture spanning from the nano/microscopic level to the macroscopic. Bone grafts are in high demand due to the rising number of surgeries because of increasing incidence of orthopedic disorders, non‐union fractures, and injuries in the geriatric population. The bone scaffolds need to provide porous matrix with interconnected porosity for tissue growth as well as sufficient strength to withstand physiological loads, and be compatible with physiological remodeling by osteoclasts/osteoblasts. The‐state‐of‐art additive manufacturing (AM) technologies for bone tissue engineering enable the manipulation of gross geometries, for example, they rely on the gaps between printed materials to create interconnected pores in 3D scaffolds. Herein, the authors firstly print hierarchical and porous hydroxyapatite (HAP) structures with interconnected pores to mimic human bones from microscopic (below 10 µm) to macroscopic (submillimeter to millimeter level) by combining freeze casting and extrusion‐based 3D printing. The compression test of 3D printed scaffold demonstrates superior compressive stress (22 MPa) and strain (4.4%). The human mesenchymal stromal cells (MSCs) tests demonstrate the biocompatibility of printed scaffold.
-
more » « less
Additive manufacturing, commonly known as 3D printing, significantly simplifies the manufacturing process for soft electronics. This work demonstrates the feasibility of a fully 3D‐printed flexible poly(vinylidene fluoride) (PVdF) capacitive temperature sensor. The sensor is constructed using fused deposition modeling (FDM)‐printed PVdF film as the dielectric (thickness ≈180–280 μm) sandwiched between two parallel Direct Ink Writing (DIW) printed silver electrodes (entire device thickness ≈200–380 μm). The motion of the nozzle can facilitate mechanical drawing to the molten PVdF filament, which is a necessary condition to increase the β‐phase content (critical for the sensitivity of the sensor). With optimized printing parameters, the highest β‐phase content (21.30%) is achieved when printing with a nozzle temperature of 200 °C and a print speed of 70 mm s−1. The research demonstrates the application of the device as a temperature sensor by applying heating‐and‐cooling cycles from room temperature (25 °C) up to 140 °C while measuring the capacitance as a function of frequency under different temperatures. The sensor exhibits a stable sensitivity of 3 pF °C−1at 102 Hz and higher frequencies and improved sensitivities at frequencies higher than 102 Hz after dielectric polarization via the corona poling method.
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1007/s10856-021-06569-9
