- Award ID(s):
- 1928622
- PAR ID:
- 10341620
- Date Published:
- Journal Name:
- American journal of advanced research
- Volume:
- 5
- Issue:
- December
- ISSN:
- 2572-8830
- Page Range / eLocation ID:
- 7-12
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
In the last few decades, fiber reinforced composites have been established as the materials of choice for lightweight applications in a large spectrum of applications ranging from aerospace, defense, and marine industries to automotive products and consumer goods. With the growing shift to sustainable resources, natural fibers, especially plant fibers, received increased interest throughout the years. Among these natural fibers, silks stand out with low stiffness and a high failure strain, unlike conventional fibers such as carbon or glass. Although gaining traction as a natural alternative reinforcement, silk still has little to no commercial uses despite its higher performance. Besides its higher mechanical properties and lightweight, silk exhibits other attractive properties such as improved flame retardancy and biodegradability. To take advantage of these features, proper fiber/matrix adhesion must be achieved. Such silk/matrix bonding can be inferred from the silk/resin affinity during composite manufacturing. In this study, the affinity/wettability of several silk/resin systems were analyzed via static contact angles using imageJ software to determine candidates for silk reinforced composite laminates with better adhesion. To this end, a combination of four silk fibers and three resin systems were investigated. The investigated silk fibers were Ahimsa, Charmeuse, Habotai, and Tussah; and the resins included a vinyl ester (Hydrex) and two epoxies (INF114 and INR). For Tussah fibers, initial contact angles were consistently one of the lowest. However, these fibers exhibited a higher contact angle over time compared to the other silk fibers studied. Conversely, Ahimsa silk fibers showed the highest initial contact angle, then quickly dropped to com-plete wetting. Habotai fibers dropped towards complete wetting quickly, however, consistently slowed considerably shortly after. Charmeuse fibers performed similarly to Ahimsa fibers with Hydrex, however was considerably slower to wetting with the other resins. Among the investigated resins, Hydrex showed the best affinity to silk fibers with the majority of the lowest initial contact angles and the fastest to complete wetting. INF114 consistently receded at a slower, albeit steady, rate until reaching complete wetting apart from Tussah. INR showed the highest initial contact angles and never reached complete wetting after an hour for two of the four silks investigated. Therefore, the best silk/resin affinity was observed for the Ahimsa and Charmeuse silk fibers and the Hydrex vinyl ester resin. In future work, silk composites with these constituents would be investigated.more » « less
-
Abstract Manufacturing and investigating metallic‐glass‐fiber‐reinforced epoxies is an important new attempt to present their potential to contribute to the aviation industry. In order to explore the energy absorption in novel CoFeSiB metallic‐glass‐fiber/epoxy resin composites, CoFeSiB/epoxy resin composite cylinders with different fiber volume fractions were prepared by a hot‐pressing method. The amorphism of the metal fibers was analyzed using x‐ray diffraction. The quasi‐static compression tests were performed on different fiber oriented samples with a diameter of 3.6 mm and a height of 7.2 mm. The sample with the fiber orientation [0°/90°] has a higher energy absorption capacity, compared to the one with the fiber orientation [0°/0°]. The dynamic‐ compression tests were performed on the [0°/0°] samples with a diameter of 3 mm and height of 6 mm at different air pressures. The compression fracture surfaces were examined by scanning electron microscope. Then the energy absorption mechanism of the composites was investigated. This study is of great significance for the energy absorption in amorphous metal fiber/epoxy composites.
-
This study compared the mechanical properties of a recyclable flax fiber reinforced polymer composite (FFRP) with a covalent adaptable network (CAN) matrix to an FFRP composite with a conventional (unrecyclable) epoxy resin matrix. The results indicated that composites fabricated via vacuum-assisted resin transfer molding (VARTM) exhibited up to 19% higher tensile modulus and strength compared to those fabricated via hand layup, attributed to reduced air void content and more uniform fiber alignment. Microscopy evidence supported by mechanical property tests revealed superior adhesion of the CAN matrix to flax fibers compared to conventional epoxy resin. Additionally, a solvent-based method was demonstrated for separating fibers from the CAN matrix, facilitating reuse or upcycling.more » « less
-
Abstract Smart textiles that sense, interact, and adapt to environmental stimuli have provided exciting new opportunities for a variety of applications. However, current advances have largely remained at the research stage due to the high cost, complexity of manufacturing, and uncomfortableness of environment‐sensitive materials. In contrast, natural textile materials are more attractive for smart textiles due to their merits in terms of low cost and comfortability. Here, water fog and humidity‐driven torsional and tensile actuation of thermally set twisted, coiled, plied silk fibers, and weave textiles from these silk fibers are reported. When exposed to water fog, the torsional silk fiber provides a fully reversible torsional stroke of 547° mm−1. Coiled‐and‐thermoset silk yarns provide a 70% contraction when the relative humidity is changed from 20% to 80%. Such an excellent actuation behavior originates from water absorption‐induced loss of hydrogen bonds within the silk proteins and the associated structural transformation, which are corroborated by atomistic and macroscopic characterization of silk and molecular dynamics simulations. With its large abundance, cost‐effectiveness, and comfortability for wearing, the silk muscles will open up additional possibilities in industrial applications, such as smart textiles and soft robotics.
-
Thermoset polymer composites, known for their outstanding thermal, mechanical, and chemical properties, have found applications in diverse fields, including aerospace and automotive industries. These polymers, once cured, cannot be recycled, making the end-of-life management of these composites very difficult and posing an environmental challenge. Conventional recycling methods are unsuitable for thermosets, forcing their accumulation in landfills and raising environmental concerns. One possible solution to overcome this concern is to use resins or curing agents, or both, made from biodegradable materials. This study explores the fabrication and characterization of polymer composites using a commercially available green curing agent made from biomass. The composite laminates were fabricated using HVARTM (Heated Vacuum Assisted Resin Transfer Molding) process. In this process, heat pads are used to increase the temperature of both the epoxy resin and the plain weave carbon fiber laminate to a desired temperature, providing ease of flow to the resin. Small coupons were cut from the laminate using a water jet machine to study the flexural behavior of the composite in accordance with ASTM testing standards and compared with composite coupons fabricated using conventional epoxy resin.more » « less