skip to main content


Title: Tuning the defects in MoS 2 /reduced graphene oxide 2D hybrid materials for optimizing battery performance
This study reports the preparation of a set of hybrid materials consisting of molybdenum disulfide (MoS 2 ) nanopatches on reduced graphene oxide (rGO) nanosheets by microwave specific heating of graphene oxide and molecular molybdenum precursors followed by thermal annealing in 3% H 2 and 97% Ar. The microwave process converts graphene oxide to ordered rGO nanosheets that are sandwiched between uniform thin layers of amorphous molybdenum trisulfide (MoS 3 ). The subsequent thermal annealing converts the intermediate layers into MoS 2 nanopatches with two-dimensional layered structures whose defect density is tunable by controlling the annealing temperature at 250, 325 and 600 °C, respectively. All three MoS 2 /rGO samples and the MoS 3 /rGO intermediate after the microwave step show a high Li-ion intercalation capacity in the initial 10 cycles (over 519 mA h g MoSx −1 , ∼3.1 Li + ions per MoS 2 ) which is attributed to the small MoS 2 nanopatches in the MoS 2 /rGO hybrids while the effect of further S-rich defects is insignificant. In contrast, the Zn-ion storage properties strongly depend on the defects in the MoS 2 nanopatches. The highly defective MoS 2 /rGO hybrid prepared by annealing at 250 °C shows the highest initial Zn-ion storage capacity (∼300 mA h g MoSx −1 ) and close to 100% coulombic efficiency, which is dominated by pseudocapacitive surface reactions at the edges or defects in the MoS 2 nanopatches. The fast fading in the initial cycles can be mitigated by applying higher charge/discharge currents or extended cycles. This study validates that defect engineering is critical for improving Zn-ion storage.  more » « less
Award ID(s):
1707585
PAR ID:
10347111
Author(s) / Creator(s):
; ; ; ; ;
Date Published:
Journal Name:
Sustainable Energy & Fuels
Volume:
5
Issue:
16
ISSN:
2398-4902
Page Range / eLocation ID:
4002 to 4014
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. Amorphous molybdenum sulfide (a-MoS3) is a promising non-precious electrocatalyst for hydrogen evolution reaction owing to the abundant defective active sites. Here in, we show a rapid microwave-assisted synthesis method to produce a-MoS3 catalysts on reduced graphene oxide (rGO) substrates. The a-MoS3 reported in this study comprise of two possible 1D chain-like structures, i.e., with molybdenum (IV) in Weber’s model and molybdenum (V) in Hibble’s model, unlike the polymeric cluster type a-MoS3 structures reported in literature. Thermal annealing of the microwave-prepared a-MoS3 produced a family of defect-engineered MoSx/rGO hybrids, from a-MoS3 to crystalline MoS2, which showed tunable HER activities. XPS analysis provided in-depth understanding of the compositional changes in MoSx/rGO with thermal annealing. The a-MoS3/rGO 250 (annealed at 250 ◦C) exhibited the highest HER catalytic activity among all the MoSx/rGO hybrids, with an overpotential of 208 mV at 10 mA/cm2, a low Tafel slope of 52 mV/decade, a high double layer capacitance of 3.7 mF/cm2 and a high TOF value of 0.43 H2/s per site at the HER overpotential of 208 mV. The excellent HER activity is attributed to both MoV and sulfur active sites. This study provides a controllable, scalable and rapid synthesis method to produce 1D chain-like a-MoS3 structures for HER electrocatalysis. 
    more » « less
  2. Molybdenum disulfide (MoS 2 ) may be a promising alternative for lithium ion batteries (LIBs) because it offers a unique layered crystal structure with a large and tunable distance between layers. This enables the anticipated excellent rate and cycling stability because they can promote the reversible lithium ion intercalation and de-intercalation without huge volume change which consequently prevents the pulverization of active materials during repeated charge and discharge processes. Herein, we prepared hierarchical MoS 2 –carbon (MoS 2 –C) microspheres via a continuous and scalable ultrasonic nebulization assisted route. The structure, composition, and electrochemical properties are investigated in detail. The MoS 2 –C microspheres consist of few-layer MoS 2 nanosheets bridged by carbon, which separates the exfoliated MoS 2 layers and prevents their aggregation and restacking, thus leading to improved kinetic, enhanced conductivity and structural integrity. The novel architecture offers additional merits such as overall large size and high packing density, which promotes their practical applications. The MoS 2 –C microspheres have been demonstrated with excellent electrochemical performances in terms of low resistance, high capacity even at large current density, stable cycling performance, etc. The electrodes exhibited 800 mA h g −1 at 1000 mA g −1 over 170 cycles. At a higher current density of 3200 mA g −1 , a capacity of 730 mA h g −1 can be also maintained. The MoS 2 –C microspheres are practically applicable not only because of the continuous and large scale synthesis via the current strategy, but also the possess a robust and integrated architecture which ensures the excellent electrochemical properties. 
    more » « less
  3. Abstract

    A novel approach to leverage the extraordinary properties of graphene for designing thin film strain sensors is demonstrated. Graphene nanosheets (GNS) are produced from graphite by a liquid phase exfoliation (LPE) method using water along withN‐methylpyrrolidinone (NMP) as cosolvents. It is found that the water‐NMP solvent system enhances the exfoliation yield and the stability of the GNS dispersion, thereby lowering the number of defects in the GNS basal plane. Both LPE‐based GNS and reduced graphene oxide (RGO) are synthesized for fabricating thin film strain sensors and for comparison purposes. Detailed micro‐Raman, X‐ray photoelectron spectroscopy, and transmission electron microscopy studies indicate that the as‐produced GNS exhibits lower defects than RGO nanosheets. The strain sensing study reveals that strain sensors fabricated using low‐defect GNS exhibit enhanced electrical and electromechanical properties, including higher electrical conductivity, lower noise floor, and more stable electromechanical response as compared to RGO‐based sensors.

     
    more » « less
  4. Advances in the synthesis and processing of graphene-based materials have presented the opportunity to design novel lithium-ion battery (LIB) anode materials that can meet the power requirements of next-generation power devices. In this work, a poly(methacrylic acid) (PMAA)-induced self-assembly process was used to design super-mesoporous Fe 3 O 4 and reduced-graphene-oxide (Fe 3 O 4 @RGO) anode materials. We demonstrate the relationship between the media pH and Fe 3 O 4 @RGO nanostructure, in terms of dispersion state of PMAA-stabilized Fe 3 O 4 @GO sheets at different surrounding pH values, and porosity of the resulted Fe 3 O 4 @RGO anode. The anode shows a high surface area of 338.8 m 2 g −1 with a large amount of 10–40 nm mesopores, which facilitates the kinetics of Li-ions and electrons, and improves electrode durability. As a result, Fe 3 O 4 @RGO delivers high specific-charge capacities of 740 mA h g −1 to 200 mA h g −1 at various current densities of 0.5 A g −1 to 10 A g −1 , and an excellent capacity-retention capability even after long-term charge–discharge cycles. The PMAA-induced assembly method addresses the issue of poor dispersion of Fe 3 O 4 -coated graphene materials—which is a major impediment in the synthesis process—and provides a facile synthetic pathway for depositing Fe 3 O 4 and other metal oxide nanoparticles on highly porous RGO. 
    more » « less
  5. null (Ed.)
    Both electronic and ionic conductivities are of high importance to the performance of anode materials for Li-ion batteries. Many large capacity anode materials (such as Ge) do not have sufficiently high electronic and ionic conductivities required for high-rate cycling. Here, we report a novel ternary compound, copper germanium phosphide (CuGe 2 P 3 ), as a high-rate anode. Being synthesized via a facile and scalable mechanochemistry method, CuGe 2 P 3 has a cation-disordered sphalerite structure and offers higher ionic and electronic conductivities and better tolerance to volume change during cycling than Ge, as confirmed by first principles calculations and experimental characterization, including high-resolution synchrotron X-ray diffraction, HRTEM, SAED, XPS and Raman spectroscopy. Furthermore, the results suggest that CuGe 2 P 3 has a reversible Li-storage mechanism of conversion reaction. When composited with graphite by virtue of a two-stage ball-milling process, the yolk–shell structure of the amorphous carbon-coated CuGe 2 P 3 nanocomposite (CuGe 2 P 3 /C@Graphene) delivers a high initial coulombic efficiency (91%), a superior cycling stability (1312 mA h g −1 capacity after 600 cycles at 0.2 A g −1 and 876 mA h g −1 capacity after 1600 cycles at 2 A g −1 ), and an excellent rate capability (386 mA h g −1 capacity at 30 A g −1 ), surpassing most Ge-based anodes reported to date. Moreover, a series of cation-disordered new phases in the Cu(Zn)–Ge–P family with various cation ratios offer similar Li-storage properties, achieving high reversible capacities with high initial coulombic efficiencies and desirable redox chemistry with improved safety. 
    more » « less