skip to main content


Title: Topology Optimization of Heat Sink for 3D Integrated Power Converters
This paper proposes a density-based topology optimization scheme to design a heat sink for the application of a 3D integrated SIC-based 75 kVA Intelligent Power Stage (IPS). The heat sink design considers the heat conduction and convection effects with forced air cooling. The objective function is to minimize the thermal compliance of the whole structure. A volume constraint is imposed to reduce the overall volume of the designed heat sink to make it conformal to the underlying power devices. Some numerical techniques like filtering and projection schemes are employed to render a crisp design. Some 2D benchmarks examples are first provided to demonstrate the effectiveness of the proposed method. Then a 3D heat sink, especially designed for the 3D IPS, is topologically optimized. The classic tree-like structure is reproduced to reinforce the convection effect. Some comparisons with the intuitive baseline designs are made through numerical simulation. The optimized heat sinks are shown to provide a more efficient cooling performance for the 3D integrated power converter assembly.  more » « less
Award ID(s):
1762287
NSF-PAR ID:
10351918
Author(s) / Creator(s):
; ; ; ;
Date Published:
Journal Name:
Proceedings of the ASME International Technical Conference and Exhibition on Packaging and Integration of Electronic and Photonic Microsystems
ISSN:
2378-8267
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. Abstract This work presents an approach to optimally designing a composite with thermal conductivity enhancers infiltrated with phase change material based on figure of merit (FOM) for thermal management of portable electronic devices. The FOM defines the balance between effective thermal conductivity and energy storage capacity. In this study, thermal conductivity enhancers are in the form of a honeycomb structure. Thermal conductivity enhancers are often used in conjunction with phase change material to enhance the conductivity of the composite medium. Under constrained heat sink volume, the higher volume fraction of thermal conductivity enhancers improves the effective thermal conductivity of the composite, while it reduces the amount of latent heat storage simultaneously. This work arrives at the optimal design of composite for electronic cooling by maximizing the FOM to resolve the stated tradeoff. In this study, the total volume of the composite and the interfacial heat transfer area between the phase change material and thermal conductivity enhancers are constrained for all design points. A benchmarked two-dimensional direct computational fluid dynamics model was employed to investigate the thermal performance of the phase change material and thermal conductivity enhancer composite. Furthermore, assuming conduction-dominated heat transfer in the composite, a simplified effective numerical model that solves the single energy equation with the effective properties of the phase change material and thermal conductivity enhancer has been developed. The effective properties like heat capacity can be obtained by volume averaging; however, effective thermal conductivity (required to calculate FOM) is unknown. The effective thermal conductivity of the composite is obtained by minimizing the error between the transient temperature gradient of direct and simplified model by iteratively varying the effective thermal conductivity. The FOM is maximized to find the optimal volume fraction for the present design. 
    more » « less
  2. Abstract Thermal metamaterials exhibit thermal properties that do not exist in nature but can be rationally designed to offer unique capabilities of controlling heat transfer. Recent advances have demonstrated successful manipulation of conductive heat transfer and led to novel heat guiding structures such as thermal cloaks, concentrators, etc. These advances imply new opportunities to guide heat transfer in complex systems and new packaging approaches as related to thermal management of electronics. Such aspects are important, as trends of electronics packaging toward higher power, higher density, and 2.5D/3D integration are making thermal management even more challenging. While conventional cooling solutions based on large thermal-conductivity materials as well as heat pipes and heat exchangers may dissipate the heat from a source to a sink in a uniform manner, thermal metamaterials could help dissipate the heat in a deterministic manner and avoid thermal crosstalk and local hot spots. This paper reviews recent advances of thermal metamaterials that are potentially relevant to electronics packaging. While providing an overview of the state-of-the-art and critical 2.5D/3D-integrated packaging challenges, this paper also discusses the implications of thermal metamaterials for the future of electronic packaging thermal management. Thermal metamaterials could provide a solution to nontrivial thermal management challenges. Future research will need to take on the new challenges in implementing the thermal metamaterial designs in high-performance heterogeneous packages to continue to advance the state-of-the-art in electronics packaging. 
    more » « less
  3. Abstract Heterogeneous and complex electronic packages may require unique thermomechanical structures to provide optimal heat guiding. In particular, when a heat source and a heat sink are not aligned and do not allow a direct path, conventional thermal management methods providing uniform heat dissipation may not be appropriate. Here we present a topology optimization method to find thermally conductive and mechanically stable structures for optimal heat guiding under various heat source-sink arrangements. To exploit the capabilities, we consider complex heat guiding scenarios and three-dimensional (3D) serpentine structures to carry the heat with corner angles ranging from 30 deg to 90 deg. While the thermal objective function is defined to minimize the temperature gradient, the mechanical objective function is defined to maximize the stiffness with a volume constraint. Our simulations show that the optimized structures can have a thermal resistance of less than 32% and stiffness greater than 43% compared to reference structures with no topology optimization at an identical volume fraction. The significant difference in thermal resistance is attributed to a thermally dead volume near the sharp corners. As a proof-of-concept experiment, we have created 3D heat guiding structures using a selective laser melting technique and characterized their thermal properties using an infrared thermography technique. The experiment shows the thermal resistance of the thermally optimized structure is 29% less than that of the reference structure. These results present the unique capabilities of topology optimization and 3D manufacturing in enabling optimal heat guiding for heterogeneous systems and advancing the state-of-the-art in electronics packaging. 
    more » « less
  4. This research investigates the design of structurally performant, lightweight architectural elements produced through concrete 3D printing (C3DP). Traditionally, concrete requires dense and sturdy formwork, whose production adds significantly to the total cost and results in massive and heavy parts after demolding. C3DP offers the unique opportunity to both eliminate the need for formwork and to create lighter parts by introducing internal voids and cavities. The advent of additive manufacturing in a broad range of scales, materials, industries, and applications, led to increased interest and intense research into different types of porous structures, their geometry, and structural performance under various boundary conditions. Precise control over the sparse distribution of material allows not only for parts with similar strength at reduced mass but even for modifications of mechanical properties, like turning brittle materials into elastic or shock-absorbent ones. While with powder-based additive manufacturing processes like metal 3D printing, truss-based lattices have become very popular for the light-weighting of parts or to provide tissue growth scaffolds for medical implants, their geometry – a sparse space frame resulting in numerous individual contour islands and accentuated overhangs – cannot as easily be produced by C3DP, which is based on a continuous material extrusion. Alternative types of micro-structures, so-called triply periodic minimal surfaces (TPMS), are better suited for this process as they are, as their name suggests, consisting of one continuous surface dividing space into two separate but interwoven subspaces. TPMS are therefore very popular for the efficient design of heat exchangers. We develop and present a continuous and integrated workflow, in which the architectural elements and their structural requirements are designed through transitioning back and forth between the force and the form diagram using 3D graphic statics [1]. The members and their topology from the abstract graph of the conceptual form diagram are seamlessly connected to the volumetric modeling (VM) framework, responsible for the definition of the part geometry [2]. VM represents form assigned distance functions (SDF) and can easily handle complex topologies and flawless Boolean operations of not only the outer shell geometry but also the internal micro-structural infill patterns (Fig. 1, a). In an iterative feedback loop, the infill can be further optimized to leave the material only along certain internal stress trajectories (force flows). This functional grading controlling the relative density is done based on the FE analysis results. The stress distribution is thereby defined as a three-dimensional field (Fig. 1, b). Its values can factor into the SDF equation and be used to modify the wavelength (periodicity) of the TPMS, the local thickness of the surface shell, the solid to void fraction by shifting the threshold iso-value or even the alignment and orientation of the unit cells (Fig. 1, c). They can be arranged in an orthogonal, polar- or even spherical coordinate system to optimally adapt to structural necessities. The TPMS pattern can also gradually transition from one type into another type along the gradient of a spatial function. 
    more » « less
  5. Motivated by the search for sharp bounds on turbulent heat transfer as well as the design of optimal heat exchangers, we consider incompressible flows that most efficiently cool an internally heated disc. Heat enters via a distributed source, is passively advected and diffused, and exits through the boundary at a fixed temperature. We seek an advecting flow to optimize this exchange. Previous work on energy-constrained cooling with a constant source has conjectured that global optimizers should resemble convection rolls; we prove one-sided bounds on energy-constrained cooling corresponding to, but not resolving, this conjecture. In the case of an enstrophy constraint, our results are more complete: we construct a family of self-similar, tree-like ‘branching flows’ whose cooling we prove is within a logarithm of globally optimal. These results hold for general space- and time-dependent source–sink distributions that add more heat than they remove. Our main technical tool is a non-local Dirichlet-like variational principle for bounding solutions of the inhomogeneous advection–diffusion equation with a divergence-free velocity. This article is part of the theme issue ‘Mathematical problems in physical fluid dynamics (part 1)’. 
    more » « less