skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


Title: The effects of soft and rough substrates on suction-based adhesion
ABSTRACT The northern clingfish (Gobiesox maeandricus) has a suction-based adhesive disc that can stick to incredibly rough surfaces, a challenge for stiff commercial suction cups. Both clingfish discs and bioinspired suction cups have stiff cores but flexible edges that can deform to overcome surface irregularities. Compliant surfaces are common in nature and technical settings, but performance data for fish and commercial cups are gathered from stiff surfaces. We quantified the interaction between substrate compliance, surface roughness and suction performance for the northern clingfish, commercial suction cups and three biomimetic suction cups with disc rims of varying compliance. We found that all cups stick better on stiffer substrates and worse on more compliant ones, as indicated by peak stress values. On compliant substrates, surface roughness had little effect on adhesion, even for commercial cups that normally fail on hard, rough surfaces. We propose that suction performance on compliant substrates can be explained in part by effective elastic modulus, the combined elastic modulus from a cup–substrate interaction. Of all the tested cups, the biomimetic cups performed the best on compliant surfaces, highlighting their potential to be used in medical and marine geotechnical fields. Lastly, we discuss the overmolding technique used to generate the bioinspired cups and how it is an important tool for studying biology.  more » « less
Award ID(s):
1759637 1701665
PAR ID:
10353979
Author(s) / Creator(s):
;
Date Published:
Journal Name:
Journal of Experimental Biology
Volume:
225
Issue:
9
ISSN:
0022-0949
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; ; (, Flexible and Printed Electronics)
    Abstract Flexible electronics often employ composite inks consisting of conductive flakes embedded in a polymer matrix to transmit electrical signal. Recently, localized necking was identified as a cause of a substantial increase in normalized resistance with applied strain thereby adversely impacting electrical performance. The current study explores two possible contributing factors for the formation of such localization—ink surface roughness and local variations in silver flake volume fraction. Uniaxial tension experiments of a DuPont 5025 type ink are used to inform a constitutive model implemented using finite element method on different substrates. Surface roughness was modeled by sinusoidal variation in ink height, whose amplitude and wavelength are informed by experimental laser profilometry scan data. Local flake fraction variations obtained from experimental measurements before applying any strain, were modeled as local variations in the elastic modulus according to an inverse rule of mixtures between the silver flake and acrylic binder material properties. The study identified that the ink height roughness is the most impactful contributor to the subsequent strain localization. The substrate elastic properties impact the number and magnitude of localization bands, with the stiffer substrate delocalizing strain and averting catastrophic crack formation seen with a more compliant substrate. The model incorporating surface roughness closely matches experimental measurements of local strain across different substrates. The study can inform designers of the adverse impact of ink surface roughness on localization and subsequent detrimental increase of the resistance. 
    more » « less
  2. ; (, Integrative and Comparative Biology)
    null (Ed.)
    Synopsis Animals clinging to natural surfaces have to generate attachment across a range of surface roughnesses in both dry and wet conditions. Plethodontid salamanders can be aquatic, semi-aquatic, terrestrial, arboreal, troglodytic, saxicolous, and fossorial and therefore may need to climb on and over rocks, tree trunks, plant leaves, and stems, as well as move through soil and water. Sixteen species of salamanders were tested to determine the effects of substrate roughness and wetness on maximum cling angle. Substrate roughness had a significant effect on maximum cling angle, an effect that varied among species. Substrates of intermediate roughness (asperity size 100–350 µm) resulted in the poorest attachment performance for all species. Small species performed best on smooth substrates, while large species showed significant improvement on the roughest substrates (asperity size 1000–4000 µm), possibly switching from mucus adhesion on a smooth substrate to an interlocking attachment on rough substrates. Water, in the form of a misted substrate coating and a flowing stream, decreased cling performance in salamanders on smooth substrates. However, small salamanders significantly increased maximum cling angle on wetted substrates of intermediate roughness, compared with the dry condition. Study of cling performance and its relationship to surface properties may cast light onto how this group of salamanders has radiated into the most speciose family of salamanders that occupies diverse habitats across an enormous geographical range. 
    more » « less
  3. ; ; ; (, Physical Review Research)
    Adhesives require molecular contact, which is governed by roughness, modulus, and load. Here, we measured adhesion for stiff glassy polymer layers of varying thickness on top of a soft elastomer with rough substrates. We found that a 90-nm-thick PMMA layer on a softer elastic block was sufficient to drop macroscopic adhesion to almost zero during the loading cycle. This drop in adhesion for bilayers follows the modified Persson-Tosatti model, where the elastic energy for conformal contact depends on the thickness and modulus of the bilayer. In contrast, we observed no dependence on thickness of the PMMA layer on the work of adhesion calculated using the pull-off forces. Understanding how mechanical gradients (like bilayers) affect adhesion is critical for areas such as adhesion, friction, and colloidal and granular physics. Published by the American Physical Society2024 
    more » « less
  4. (, Proceedings of the IEEERSJ International Conference on Intelligent Robots and Systems)
    null (Ed.)
    As robotic technologies advance and robots move out of factories and labs into the real world, grip on a variety of surfaces (e.g. smooth or rough) in a variety of conditions (e.g. dry or wet) becomes increasingly important. Bioinspired “microspines” have been previously explored, but primarily for vertical climbing applications or for small-scale robots applying low forces (less than 1 N). Further, these works primarily focused on rough surfaces. To advance this area of research, we present a composite material comprising high- friction rubber and compliant nitinol microspines which can passively retract below the surface of the rubber. We show that the composite can support large loads (greater than 75 N) with a high coefficient of friction on both smooth and rough surfaces (μ > 1.1), outperforming microspines alone on smooth surfaces and rubber alone on rough surfaces, especially when wet and oily. Further, due to the retraction of the microspines, the composite does not damage relatively soft, smooth surfaces, like wood flooring. We also test durability, and show that it is improved by microspine compliance, and test the effects of varying microspine diameter, angle, and tip shape. Finally, we demonstrate that a small RC car can climb steeper slopes and stop more quickly in wet conditions with microspines. 
    more » « less
  5. ; (, Integrative and Comparative Biology)
    null (Ed.)
    Synopsis Arboreal ants must navigate variably sized and inclined linear structures across a range of substrate roughness when foraging tens of meters above the ground. To achieve this, arboreal ants use specialized adhesive pads and claws to maintain effective attachment to canopy substrates. Here, we explored the effect of substrate structure, including small and large-scale substrate roughness, substrate diameter, and substrate orientation (inclination), on adhesion and running speed of workers of one common, intermediately-sized, arboreal ant species. Normal (orthogonal) and shear (parallel) adhesive performance varied on sandpaper and natural leaf substrates, particularly at small size scales, but running speed on these substrates remained relatively constant. Running speed also varied minimally when running up and down inclined substrates, except when the substrate was positioned completely vertical. On vertical surfaces, ants ran significantly faster down than up. Ant running speed was slower on relatively narrow substrates. The results of this study show that variation in the physical properties of tree surfaces differentially affects arboreal ant adhesive and locomotor performance. Specifically, locomotor performance was much more robust to surface roughness than was adhesive performance. The results provide a basis for understanding how performance correlates of functional morphology contribute to determining local ant distributions and foraging decisions in the tropical rainforest canopy. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Save / Share this Record
  • Send to Email