An official website of the United States government
Abstract Organic semiconducting donor–acceptor polymers are promising candidates for stretchable electronics owing to their mechanical compliance. However, the effect of the electron‐donating thiophene group on the thermomechanical properties of conjugated polymers has not been carefully studied. Here, thin‐film mechanical properties are investigated for diketopyrrolopyrrole (DPP)‐based conjugated polymers with varying numbers of isolated thiophene moieties and sizes of fused thiophene rings in the polymer backbone. Interestingly, it is found that these thiophene units act as an antiplasticizer, where more isolated thiophene rings or bigger fused rings result in an increased glass transition temperature (Tg) of the polymer backbone, and consequently elastic modulus of the respective DPP polymers. Detailed morphological studies suggests that all samples show similar semicrystalline morphology. This antiplasticization effect also exists inpara‐azaquinodimethane‐based conjugated polymers, indicating that this can be a general trend for various conjugated polymer systems. Using the knowledge gained above, a new DPP‐based polymer with increased alkyl side chain density through attaching alky chains to the thiophene unit is engineered. The new DPP polymer demonstrates a record lowTg, and 50% lower elastic modulus than a reference polymer without side‐chain decorated on the thiophene unit. This work provides a general design rule for making low‐Tgconjugated polymers for stretchable electronics.
more »
« less
Molecular Origin of Strain‐Induced Chain Alignment in PDPP‐Based Semiconducting Polymeric Thin Films
Abstract Donor–acceptor (D–A) type semiconducting polymers have shown great potential for the application of deformable and stretchable electronics in recent decades. However, due to their heterogeneous structure with rigid backbones and long solubilizing side chains, the fundamental understanding of their molecular picture upon mechanical deformation still lacks investigation. Here, the molecular orientation of diketopyrrolopyrrole (DPP)‐based D–A polymer thin films is probed under tensile deformation via both experimental measurements and molecular modeling. The detailed morphological analysis demonstrates highly aligned polymer crystallites upon deformation, while the degree of backbone alignment is limited within the crystalline domain. Besides, the aromatic ring on polymer backbones rotates parallel to the strain direction despite the relatively low overall chain anisotropy. The effect of side‐chain length on the DPP chain alignment is observed to be less noticeable. These observations are distinct from traditional linear‐chain semicrystalline polymers like polyethylene due to distinct characteristics of backbone/side‐chain combination and the crystallographic characteristics in DPP polymers. Furthermore, a stable and isotropic charge carrier mobility is obtained from fabricated organic field‐effect transistors. This study deconvolutes the alignment of different components within the thin‐film microstructure and highlights that crystallite rotation and chain slippage are the primary deformation mechanisms for semiconducting polymers.
more »
« less
- PAR ID:
- 10360458
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Advanced Functional Materials
- Volume:
- 31
- Issue:
- 21
- ISSN:
- 1616-301X
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract Semiconducting donor–acceptor (D–A) polymers have attracted considerable attention toward the application of organic electronic and optoelectronic devices. However, a rational design rule for making semiconducting polymers with desired thermal and mechanical properties is currently lacking, which greatly limits the development of new polymers for advanced applications. Here, polydiketopyrrolopyrrole (PDPP)‐based D–A polymers with varied alkyl side‐chain lengths and backbone moieties are systematically designed, followed by investigating their thermal and thin film mechanical responses. The experimental results show a reduction in both elastic modulus and glass transition temperature (Tg) with increasing side‐chain length, which is further verified through coarse‐grained molecular dynamics simulations. Informed from experimental results, a mass‐per‐flexible bond model is developed to capture such observation through a linear correlation betweenTgand polymer chain flexibility. Using this model, a wide range of backboneTgover 80 °C and elastic modulus over 400 MPa can be predicted for PDPP‐based polymers. This study highlights the important role of side‐chain structure in influencing the thermomechanical performance of conjugated polymers, and provides an effective strategy to design and predictTgand elastic modulus of future new D–A polymers.more » « less
-
The morphology of semiconducting polymer thin films is known to have a profound effect on their opto-electronic properties. Although considerable efforts have been made to control and understand the processes which influence the structures of these systems, it remains largely unclear what physical factors determine the arrangement of polymer chains in spin-cast films. Here, we investigate the role that the liquid–vapor interfaces in chlorobenzene solutions of poly(3-hexylthiophene) [P3HT] play in the conformational geometries adopted by the polymers. Using all-atom molecular dynamics (MD), and supported by toy-model simulations, we demonstrate that, with increasing concentration, P3HT oligomers in solution exhibit a strong propensity for the liquid–vapor interface. Due to the differential solubility of the backbone and side chains of the oligomers, in the vicinity of this interface, hexyl chains and the thiophene rings, have a clear orientational preference with respect to the liquid surface. At high concentrations, we additionally establish a substantial degree of inter-oligomer alignment and thiophene ring stacking near the interface. Our results broadly concur with the limited existing experimental evidence and we suggest that the interfacial structure can act as a template for film structure. We argue that the differences in solvent affinity of the side chain and backbone moieties are the driving force for the anisotropic orientations of the polymers near the interface. This finer grained description contrasts with the usual monolithic characterization of polymer units. Since this phenomenon can be controlled by concurrent chemical design and the choice of solvents, this work establishes a fabrication principle which may be useful to develop more highly functional polymer films.more » « less
-
Abstract Tuning structures of solution‐state aggregation and aggregation‐mediated assembly pathways of conjugated polymers is crucial for optimizing their solid‐state morphology and charge‐transport property. However, it remains challenging to unravel and control the exact structures of solution aggregates, let alone to modulate assembly pathways in a controlled fashion. Herein, aggregate structures of an isoindigo–bithiophene‐based polymer (PII‐2T) are modulated by tuning selectivity of the solvent toward the side chain versus the backbone, which leads to three distinct assembly pathways: direct crystallization from side‐chain‐associated amorphous aggregates, chiral liquid crystal (LC)‐mediated assembly from semicrystalline aggregates with side‐chain and backbone stacking, and random agglomeration from backbone‐stacked semicrystalline aggregates. Importantly, it is demonstrated that the amorphous solution aggregates, compared with semicrystalline ones, lead to significantly improved alignment and reduced paracrystalline disorder in the solid state due to direct crystallization during the meniscus‐guided coating process. Alignment quantified by the dichroic ratio is enhanced by up to 14‐fold, and the charge‐carrier mobility increases by a maximum of 20‐fold in films printed from amorphous aggregates compared to those from semicrystalline aggregates. This work shows that by tuning the precise structure of solution aggregates, the assembly pathways and the resulting thin‐film morphology and device properties can be drastically tuned.more » « less
-
Abstract Polymer membranes with ultrahigh CO2permeabilities and high selectivities are needed to address some of the critical separation challenges related to energy and the environment, especially in natural gas purification and postcombustion carbon capture. However, very few solution‐processable, linear polymers are known today that access these types of characteristics, and all of the known structures achieve their separation performance through the design of rigid backbone chemistries that concomitantly increase chain stiffness and interchain spacing, thereby resulting in ultramicroporosity in solid‐state chain‐entangled films. Herein, the separation performance of a porous polymer obtained via ring‐opening metathesis polymerization is reported, which possesses a flexible backbone with rigid, fluorinated side chains. This polymer exhibits ultrahigh CO2permeability (>21 000 Barrer) and exceptional plasticization resistance (CO2plasticization pressure > 51 bar). Compared to traditional polymers of intrinsic microporosity, the rate of physical aging is slower, especially for gases with small effective diameters (i.e., He, H2, and O2). This structural design strategy, coupled with studies on fluorination, demonstrates a generalizable approach to create new polymers with flexible backbones and pore‐forming side chains that have unexplored promise for small‐molecule separations.more » « less
