In recent years, hybrid perovskite solar cells (HPSCs) have received considerable research attention due to their impressive photovoltaic performance and low‐temperature solution processing capability. However, there remain challenges related to defect passivation and enhancing the charge carrier dynamics of the perovskites, to further increase the power conversion efficiency of HPSCs. In this work, the use of a novel material, phenylhydrazinium iodide (PHAI), as an additive in MAPbI3perovskite for defect minimization and enhancement of the charge carrier dynamics of inverted HPSCs is reported. Incorporation of the PHAI in perovskite precursor solution facilitates controlled crystallization, higher carrier lifetime, as well as less recombination. In addition, PHAI additive treated HPSCs exhibit lower density of filled trap states (1010cm−2) in perovskite grain boundaries, higher charge carrier mobility (≈11 × 10−4cm2V−1s), and enhanced power conversion efficiency (≈18%) that corresponds to a ≈20% improvement in comparison to the pristine devices.
Mobilities and lifetimes of photogenerated charge carriers are core properties of photovoltaic materials and can both be characterized by contactless terahertz or microwave measurements. Here, the expertise from fifteen laboratories is combined to quantitatively model the current‐voltage characteristics of a solar cell from such measurements. To this end, the impact of measurement conditions, alternate interpretations, and experimental inter‐laboratory variations are discussed using a (Cs,FA,MA)Pb(I,Br)3halide perovskite thin‐film as a case study. At 1 sun equivalent excitation, neither transport nor recombination is significantly affected by exciton formation or trapping. Terahertz, microwave, and photoluminescence transients for the neat material yield consistent effective lifetimes implying a resistance‐free JV‐curve with a potential power conversion efficiency of 24.6 %. For grainsizes above ≈20 nm, intra‐grain charge transport is characterized by terahertz sum mobilities of ≈32 cm2V−1s−1. Drift‐diffusion simulations indicate that these intra‐grain mobilities can slightly reduce the fill factor of perovskite solar cells to 0.82, in accordance with the best‐realized devices in the literature. Beyond perovskites, this work can guide a highly predictive characterization of any emerging semiconductor for photovoltaic or photoelectrochemical energy conversion. A best practice for the interpretation of terahertz and microwave measurements on photovoltaic materials is presented.
more » « less- Award ID(s):
- 1954453
- PAR ID:
- 10368885
- Author(s) / Creator(s):
- ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; more »
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Advanced Energy Materials
- Volume:
- 12
- Issue:
- 13
- ISSN:
- 1614-6832
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
Abstract -
more » « less
Abstract In the past years, hybrid perovskite materials have attracted great attention due to their superior optoelectronic properties. In this study, the authors report the utilization of cobalt (Co2+) to partially substitute lead (Pb2+) for developing novel hybrid perovskite materials, CH3NH3Pb1‐
x Cox I3(wherex is nominal ratio,x = 0, 0.1, 0.2 and 0.4). It is found that the novel perovskite thin films possess a cubic crystal structure with superior thin film morphology and larger grain size, which is significantly different from pristine thin film, which possesses the tetragonal crystal structure, with smaller grain size. Moreover, it is found that the 3d orbital of Co2+ensures higher electron mobilities and electrical conductivities of the CH3NH3Pb1‐x Cox I3thin films than those of pristine CH3NH3Pb4thin film. As a result, a power conversion efficiency of 21.43% is observed from perovskite solar cells fabricated by the CH3NH3Pb0.9Co0.1I3thin film. Thus, the utilization of Co, partially substituting for Pb to tune physical properties of hybrid perovskite materials provides a facile way to boost device performance of perovskite solar cells. -
more » « less
Abstract Halide perovskites are currently one of the most heavily researched emerging photovoltaic materials. Despite achieving remarkable power conversion efficiencies, perovskite solar cells have not yet achieved their full potential, with the interfaces between the perovskite and the charge‐selective layers being where most recombination losses occur. In this study, a fluorinated ionic liquid (IL) is employed to modify the perovskite/SnO2interface. Using Kelvin probe and photoelectron spectroscopy measurements, it is shown that depositing the perovskite onto an IL‐treated substrate results in the crystallization of a perovskite film which has a more n‐type character, evidenced by a decrease of the work function and a shift of the Fermi level toward the conduction band. Photoluminescence spectroscopy and time‐resolved microwave conductivity are used to investigate the optoelectronic properties of the perovskite grown on neat and IL‐modified surfaces and it is found that the modified substrate yields a perovskite film which exhibits an order of magnitude lower trap density than the control. When incorporated into solar cells, this interface modification results in a reduction in the current–voltage hysteresis and an improvement in device performance, with the best performing devices achieving steady‐state PCEs exceeding 20%.
-
null (Ed.)The contactless characterization technique time resolved microwave conductivity (TRMC) provides a means to rapidly and unambiguously approximate carrier mobilities and lifetimes for a variety of semiconducting materials. When using a cavity-based approach however, the technique can conventionally only resolve carrier mobilities in the plane of the substrate. In solar cells, charge carriers are extracted in the direction perpendicular to the substrate, therefore it would be beneficial if one were able to evaluate the mobility in this direction also. Here we present a novel approach for resolving charge carrier mobilities in different planes within a sample. Using a range of 3D-printed sample holders, where the sample is held at various angles relative to the incident light, we are able to simultaneously resolve the mobility in the plane of the sample and out of the plane of the sample. As examples, we have studied the 3-dimensional corner-connected metal halide perovskite methylammonium lead iodide and the 2-dimensional perovskite precusor, lead iodide.more » « less
-
more » « less
Sn‐based perovskites are promising Pb‐free photovoltaic materials with an ideal 1.3 eV bandgap. However, to date, Sn‐based thin film perovskite solar cells have yielded relatively low power conversion efficiencies (PCEs). This is traced to their poor photophysical properties (i.e., short diffusion lengths (<30 nm) and two orders of magnitude higher defect densities) than Pb‐based systems. Herein, it is revealed that melt‐synthesized cesium tin iodide (CsSnI3) ingots containing high‐quality large single crystal (SC) grains transcend these fundamental limitations. Through detailed optical spectroscopy, their inherently superior properties are uncovered, with bulk carrier lifetimes reaching 6.6 ns, doping concentrations of around 4.5 × 1017cm−3, and minority‐carrier diffusion lengths approaching 1 µm, as compared to their polycrystalline counterparts having ≈54 ps, ≈9.2 × 1018cm−3, and ≈16 nm, respectively. CsSnI3SCs also exhibit very low surface recombination velocity of ≈2 × 103cm s−1, similar to Pb‐based perovskites. Importantly, these key parameters are comparable to high‐performance p‐type photovoltaic materials (e.g., InP crystals). The findings predict a PCE of ≈23% for optimized CsSnI3SCs solar cells, highlighting their great potential.
