An official website of the United States government
Abstract Increasing the thickness of the electrodes is considered the primary strategy to elevate battery energy density. However, as the thickness increases, rate performance, cycling performance, and mechanical stability are affected due to the sluggish ion transfer kinetics and compromised structural integrity. Inspired by the natural hierarchical porous structure of trees, electrodes with bioinspired architecture are fabricated to address these challenges. Specifically, electrodes with aligned columns consist of tree‐inspired vertical channels, and hierarchical pores are constructed by screen printing and ice‐templating, imparting enhanced electrochemical and mechanical performance. Employing an aqueous‐based binder, the LiNi0.8Mn0.1Co0.1O2cathode achieves a high areal energy density of 15.1 mWh cm−2at a rate of 1C at mass loading of 26.0 mg cm−2, benefitting from the multiscale pores that elevated charge transfer kinetics in the thick electrode. The electrodes demonstrate capacity retention of 90% at the 100th cycle at a high current density of 5.2 mA cm−2. To understand the mechanisms that promote electrode performance, simplified electro‐chemo‐mechanical models are developed, the drying process and the charge‐discharge process are simulated. The simulation results suggested that the improved performance of the designed electrode benefits from the lower ohmic overpotential and less strain gradient and stress concentration due to the hierarchical porous architecture.
more »
« less
Enabling Ultrathick Electrodes via a Microcasting Process for High Energy and Power Density Lithium‐Ion Batteries
Abstract Thickening electrodes is one effective approach to increase active material content for higher energy and low‐cost lithium‐ion batteries, but limits in charge transport and huge mechanical stress generation result in poor performance and eventual cell failure. This paper reports a new electrode fabrication process, referred to as µ‐casting, enabling ultrathick electrodes that address the trade‐off between specific capacity and areal/volumetric capacity. The proposed µ‐casting is based on a patterned blade, enabling facile fabrication of 3D electrode structures. The study reveals the governing properties of µ‐casted ultrathick electrodes and how this simultaneously improves battery energy/power performance. The process facilitates a short diffusion path structure that minimizes intercalation‐induced stress, improving energy density and cell stability. This work also investigates the issues with structural integrity, porosity, and paste rheology, and also analyzes mechanical properties due to external force. The µ‐casting enables an ultrathick electrode (≈280 µm) that more effectively utilizes NMC‐811 (LiNi0.8Mn0.1Co0.1O2) cathode and mesocarbon microbeads anode active materials compared to conventional thick electrodes, allowing high‐mass loading (35.7 mg cm−2), 40% higher specific capacity, and 30% higher areal capacity after 200 cycles, high C‐rate performance, and longer cycle life.
more »
« less
- Award ID(s):
- 1917055
- PAR ID:
- 10375982
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Advanced Energy Materials
- Volume:
- 12
- Issue:
- 38
- ISSN:
- 1614-6832
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract To achieve the high energy densities demanded by emerging technologies, lithium battery electrodes need to approach the volumetric and specific capacity limits of their electrochemically active constituents, which requires minimization of the inactive components of the electrode. However, a reduction in the percentage of inactive conductive additives limits charge transport within the battery electrode, which results in compromised electrochemical performance. Here, an electrode design that achieves efficient electron and lithium‐ion transport kinetics at exceptionally low conductive additive levels and industrially relevant active material areal loadings is introduced. Using a scalable Pickering emulsion approach, Ni‐rich LiNi0.8Co0.15Al0.05O2(NCA) cathode powders are conformally coated using only 0.5 wt% of solution‐processed graphene, resulting in an electrical conductivity that is comparable to 5 wt% carbon black. Moreover, the conformal graphene coating mitigates degradation at the cathode surface, thus providing improved electrochemical cycle life. The morphology of the electrodes also facilitates rapid lithium‐ion transport kinetics, which provides superlative rate capability. Overall, this electrode design concurrently approaches theoretical volumetric and specific capacity limits without tradeoffs in cycle life, rate capability, or active material areal loading.more » « less
-
In Ni-YSZ electrode-supported cells, gas diffusion through the electrode support layer can be a significant limitation at high H 2 or H 2 O utilization and high temperature. Conventionally, higher-porosity electrode supports are used to improve diffusion, but this diminishes the cell’s structural integrity. Alternative fabrication methods like freeze-casting and 3D-printing allow for the creation of hierarchical structures with cutouts in the cell surface that improve gas diffusion, but these methods require redesigning processing procedures to obtain the desired materials properties. This work explores the use of laser ablation to pattern cutouts into the electrode support after sintering, enabling a faster mass transport without redesigning the entire fabrication process. Current-voltage measurements of symmetric Ni-YSZ electrode-supported cells with one patterned and one un-patterned electrode demonstrate that laser-patterning improves limiting current density and effective diffusivity by as much as 30%. Mechanical testing of patterned and un-patterned cells demonstrates that patterned cells suffer relatively small reductions in fracture strength.more » « less
-
Abstract Li‐S batteries can potentially deliver high energy density and power, but polysulfide shuttle and lithium dendrite formations on Li metal anode have been the major hurdle. The polysulfide shuttle becomes severe particularly when the areal loading of the active material (sulfur) is increased to deliver the high energy density and the charge/discharge current density is raised to deliver high power. This study reports a novel mechanochemical method to create trenches on the surface of carbon nanotubes (CNTs) in free‐standing 3D porous CNT sponges. Unique spiral trenches are created by pressures during the chemical treatment process, providing polysulfide‐philic surfaces for cathode and lithiophilic surfaces for anode. The Li‐S cells made from manufacturing‐friendly sulfur‐sandwiched cathodes and lithium‐infused anodes using the mechanochemically treated electrodes exhibit a strikingly high areal capacity as high as 13.3 mAh cm−2, which is only marginally reduced even with a tenfold increase in current density (16 mA cm−2), demonstrating both high “cell‐level” energy density and power. The outstanding performance can be attributed to the significantly improved reaction kinetics and lowered overpotentials coming from the reduced interfacial resistance and charge transfer resistance at both cathodes and anodes. The trench–wall CNT sponge simultaneously tackles the most critical problems on both the cathodes and anodes of Li‐S batteries, and this method can be utilized in designing new electrode materials for energy storage and beyond.more » « less
-
Abstract An ultra‐fast electrochemical capacitor (EC) designed for efficient ripple current smoothing was fabricated using vertically oriented MoS2(VOM) nanoflakes deposited on freestanding carbonized cellulose (CC) sheets as electrodes. The daily used cellulose tissue sheets were transformed into electrode scaffolds through a rapid pyrolysis process within a preheated furnace, on which VOM nanoflakes were formed in a conventional hydrothermal process. With these ~10 μm thick VOM‐CC electrodes, ultrafast ECs with tunable frequency response and specific capacitance density were fabricated. The ECs with a cell‐level areal capacitance density of 0.8 mF/cm2at 120 Hz were demonstrated for ripple current filtering from 60 Hz to 60 kHz. At a lower frequency response level, EC cell with a large capacitance density of 4.8 mF/cm2was also demonstrated. With the facile and easily scaled up process to producing the nanostructured electrode, the miniaturized VOM‐CC based ECs have the potential to substitute the bulky aluminum electrolytic capacitors for current smoothing and pulse power applications.more » « less
