An official website of the United States government
Abstract Converting CO2to value‐added chemicals,e. g., CH3OH, is highly desirable in terms of the carbon cycling while reducing CO2emission from fossil fuel combustion. Cu‐based nanocatalysts are among the most efficient for selective CO2‐to‐CH3OH transformation; this conversion, however, suffers from low reactivity especially in the thermodynamically favored low temperature range. We herein report ultrasmall copper (Cu) nanocatalysts supported on crystalline, mesoporous zinc oxide nanoplate (Cu@mZnO) with notable activity and selectivity of CO2‐to‐CH3OH in the low temperature range of 200–250 °C. Cu@mZnO nanoplates are prepared based on the crystal‐crystal transition of mixed Cu and Zn basic carbonates to mesoporous metal oxides and subsequent hydrogen reduction. Under the nanoconfinement of mesopores in crystalline ZnO frameworks, ultrasmall Cu nanoparticles with an average diameter of 2.5 nm are produced. Cu@mZnO catalysts have a peak CH3OH formation rate of 1.13 mol h−1per 1 kg under ambient pressure at 246 °C, about 25 °C lower as compared to that of the benchmark catalyst of Cu−Zn−Al oxides. Our new synthetic strategy sheds some valuable insights into the design of porous catalysts for the important conversion of CO2‐to‐CH3OH.
more »
« less
Boosting the H 2 –D 2 Exchange Activity of Dilute Nanoporous Ti–Cu Catalysts through Oxidation–Reduction Cycle–Induced Restructuring
The use of nanoporous metals as catalysts has attracted significant interest in recent years. Their high‐curvature, nanoscale ligaments provide not only high surface area but also a high density of undercoordinated step edge and kink sites. However, their long‐term stability, especially at higher temperatures, is often limited by thermal coarsening and the associated loss of surface area. Herein, it is demonstrated that the nanoscale morphology of nanoporous Cu can be regenerated by applying oxidation/reduction cycles at 250 °C. Specifically, the morphological evolution and H2dissociation activity of hierarchical nanoporous Cu catalysts doped with Ti during structural rearrangement triggered by oxidative and reductive atmospheres at elevated temperatures are studied. In addition to coarsening of the structure at elevated temperatures, oxidation at 400 °C causes an expansion of the ligaments. Subsequent reduction at 400 °C leads to the formation of particles and a drop in the H2dissociation activity compared the fresh catalyst. However, performing the redox cycle at 250 °C reverses coarsening and boosts the H2dissociation activity for the hydrogen–deuterium (H2–D2) reaction. Herein, the possibility to reverse coarsening is demonstrated, thereby mitigating the loss of activity frequently observed in nanoporous catalysts.
more »
« less
- Award ID(s):
- 1720530
- PAR ID:
- 10391076
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Advanced Engineering Materials
- Volume:
- 25
- Issue:
- 9
- ISSN:
- 1438-1656
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract Na2WO4/SiO2, a material known to catalyze alkane selective oxidation including the oxidative coupling of methane (OCM), is demonstrated to catalyze selective hydrogen combustion (SHC) with >97 % selectivity in mixtures with several hydrocarbons (CH4, C2H6, C2H4, C3H6, C6H6) in the presence of gas‐phase dioxygen at 883–983 K. Hydrogen combustion rates exhibit a near‐first‐order dependence on H2partial pressure and are zero‐order in H2O and O2partial pressures. Mechanistic studies at 923 K using isotopically‐labeled reagents demonstrate the kinetic relevance of H−H dissociation and absence of O‐atom recombination. In situ X‐ray diffraction (XRD) and W LIII‐edge X‐ray absorption spectroscopy (XAS) studies demonstrate, respectively, a loss of Na2WO4crystallinity and lack of second‐shell coordination with respect to W6+cations below 923 K; benchmark experiments show that alkali cations must be present for the material to be selective for hydrogen combustion, but that materials containing Na alone have much lower combustion rates (per gram Na) than those containing Na and W. These data suggest a synergy between Na and W in a disordered phase at temperatures below the bulk melting point of Na2WO4(971 K) during SHC catalysis. The Na2WO4/SiO2SHC catalyst maintains stable combustion rates at temperatures ca. 100 K higher than redox‐active SHC catalysts and could potentially enable enhanced olefin yields in tandem operation of reactors combining alkane dehydrogenation with SHC processes.more » « less
-
Abstract The use of γ‐Al2O3‐supported Ni catalysts promoted with either Cu or Fe was investigated for the reductive catalytic fractionation (RCF) of hybrid poplar in methanol at 200 and 250 °C. The effectiveness of lignin depolymerization was quantified in terms of the lignin oil production, the quantity and distribution of identifiable monomers present in the lignin oil, and the yield of residual solids. All of the Ni‐based catalysts tested provided improved yields of lignin oil and monomers, along with reduced char formation, relative to blank (sans catalyst) runs. The highest monomer yield of 51 % was obtained at 250 °C over a 20 wt.% Ni‐5 wt.% Cu/Al2O3catalyst, the improved performance obtained through Cu promotion being attributed to the ability of Cu to facilitate NiO reduction, resulting in an increased amount of Ni0on the catalyst surface and, consequently, improved hydrogenation activity. The main monomers formed were propanol‐, propyl‐ and propenyl‐substituted guaiacol and syringol, the S/G ratio of the products corresponding closely to that in the native lignin.more » « less
-
TiO 2 supported catalysts have been widely studied for the selective catalytic reduction (SCR) of NO x ; however, comprehensive understanding of synergistic interactions in multi-component SCR catalysts is still lacking. Herein, transition metal elements (V, Cr, Mn, Fe, Co, Ni, Cu, La, and Ce) were loaded onto TiO 2 nanoarrays via ion-exchange using protonated titanate precursors. Amongst these catalysts, Mn-doped catalysts outperform the others with satisfactory NO conversion and N 2 selectivity. Cu co-doping into the Mn-based catalysts promotes their low-temperature activity by improving reducibility, enhancing surface Mn 4+ species and chemisorbed labile oxygen, and elevating the adsorption capacity of NH 3 and NO x species. While Ce co-doping with Mn prohibits the surface adsorption and formation of NH 3 and NO x derived species, it boosts the N 2 selectivity at high temperatures. By combining Cu and Ce as doping elements in the Mn-based catalysts, both the low-temperature activity and the high-temperature N 2 selectivity are enhanced, and the Langmuir–Hinshelwood reaction mechanism was proved to dominate in the trimetallic Cu–Ce–5Mn/TiO 2 catalysts due to the low energy barrier.more » « less
-
Abstract Converting CO2into industrially useful products is an appealing strategy for utilization of an abundant chemical resource. Electrochemical CO2reduction (eCO2R) offers a pathway to convert CO2into CO and ethylene, using renewable electricity. These products can be efficiently copolymerized by organometallic catalysts to generate polyketones. However, the conditions for these reactions are very different, presenting the challenge of coupling microenvironments typically encountered for the transformation of CO2into highly complex but desirable multicarbon products. Herein, we present a system to produce polyketone plastics entirely derived from CO2and water, where both the CO and C2H4intermediates are produced by eCO2R. In this system, a combination of Cu and Ag gas diffusion electrodes is used to generate a gas mixture with nearly equal concentrations of CO and C2H4, and a recirculatory CO2reduction loop is used to reach concentrations of above 11% each, leading to a current‐to‐polymer efficiency of up to 51% and CO2utilization of 14%.more » « less
