skip to main content


Title: Cracking behavior in lead zirconate titanate films with different Zr/Ti ratios

Crack initiation stresses for different lead zirconate titanate (PZT) film compositions were investigated. PZT/Pt/TiO2/SiO2/Si stacks with 2.0 μm thick {100} oriented PZT films at the morphotropic phase boundary (MPB) showed a characteristic strength of 1137 MPa, and the film thickness served as the limiting flaw size for failure of the film/substrate stack. In contrast, for Zr/Ti ratios of 40/60 and 30/70, the characteristic stack strength increased while the Weibull modulus decreased to values typical for that of Si. This difference is believed to be due to toughening from ferroelasticity or phase switching. X-ray diffraction showed that the volume fraction of c-domains increased in Ti-rich compositions. This would allow for more switching from c to a-domains under biaxial tensile stress. Zr/Ti concentration gradients were present for all compositions, which contributed to the observation of a rhombohedral phase off the MPB. Due to the reduced tendency toward cracking, off-MPB compositions are potentially of interest in actuators, albeit with the trade-off of needing a high actuation voltage.

 
more » « less
Award ID(s):
1841453
NSF-PAR ID:
10439896
Author(s) / Creator(s):
; ;
Publisher / Repository:
American Institute of Physics
Date Published:
Journal Name:
Applied Physics Letters
Volume:
121
Issue:
16
ISSN:
0003-6951
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. Abstract

    Ferroelectric films suffer from both aging and degradation under high ac‐field drive conditions due to loss of polarization with time. In this study, the roles of defect chemistry and internal electric fields on the long‐term stability of the properties of piezoelectric films were explored. For this purpose, lead zirconate titanate (PZT) films with a Zr/Ti ratio of 52/48 doped with Mn‐ (PMZT) or Nb‐ (PNZT) were deposited on Pt coated Si substrates by the sol‐gel method. It was demonstrated that the magnitude of the internal field is much higher in PMZT films compared to PNZT films after poling in the temperature range of 25‐200°C under an electric field of −240 kV/cm. The development of the internal field is thermally activated, with activation energies from 0.5 ± 0.06 to 0.8 ± 0.1 eV in Mn doped films and from 0.8 ± 0.1 to 1.2 ± 0.2 eV in Nb doped films. The different activation energies for imprint suggests that the physical mechanism underlying the evolution of the internal field in PMZT and PNZT films differs; the enhanced internal field upon poling is attributed to (a) alignment of oxygen vacancy—acceptor ion defect dipoles (,) in PMZT films, and (b) thermionic injection of electron charges and charge trapping in PNZT films. In either case, the internal field reduces back switching, enhances the remanent piezoelectric properties, and dramatically improves the aging behavior. PMZT films exhibited the greatest enhancement, with reduced high temperature (180°C) aging rates of 2%‐3%/decade due to improved stability of the poled state. In contrast, PNZT films showed significantly larger high temperature aging rates (15.5%/decade) in the piezoelectric coefficient, demonstrating that the fully poled state was not retained with time.

     
    more » « less
  2. Phase pure PbZr 0.52 Ti 0.48 O 3 (PZT) films with up to 13 mol. % Nb were prepared on Pt-coated Si substrates using chemical solution deposition; charge compensation for Nb was accomplished by reducing the concentration of lead in the film. For high Nb doping levels, (1) superoxidation of the PZT film surface makes the PZT/Pt interface more p-type and, hence reduces electron injection over the Schottky barrier, (2) the bulk charge transport mechanism changes from electron trapping by Ti 4+ to hole migration between lead vacancies, and (3) the ionic conductivity due to migration of oxygen vacancies decreases. For [Formula: see text] Nb, electrical degradation was controlled via field-induced accumulation of oxygen vacancies near the cathode, which, in turn, leads to Schottky barrier lowering and electron trapping by Ti 4+ . In phase pure 13 mol. % Nb doped PZT films, on the other hand, the increase in the leakage current during electrical degradation was dominated by hole migration between lead vacancies ([Formula: see text]. A much lower lifetime and drastic increase in the leakage current upon electrical degradation was observed in mixed phase PNZT films, which was attributed to (1) a more electrically conductive pyrochlore phase and (2) a high concentration of lead vacancies. 
    more » « less
  3. Abstract

    Scanning Probe Microscopy (SPM) based techniques probe material properties over microscale regions with nanoscale resolution, ultimately resulting in investigation of mesoscale functionalities. Among SPM techniques, piezoresponse force microscopy (PFM) is a highly effective tool in exploring polarization switching in ferroelectric materials. However, its signal is also sensitive to sample‐dependent electrostatic and chemo‐electromechanical changes. Literature reports have often concentrated on the evaluation of theOff‐fieldpiezoresponse, compared toOn‐fieldpiezoresponse, based on the latter's increased sensitivity to non‐ferroelectric contributions. Using machine learning approaches incorporatingboth Off‐andOn‐fieldpiezoresponse response as well asOff‐fieldresonance frequency to maximize information, switching piezoresponse in a defect‐rich Pb(Zr,Ti)O3thin film is investigated. As expected, one major contributor to the piezoresponse is mostly ferroelectric, coupled with electrostatic phenomena duringOn‐fieldmeasurements. A second component is electrostatic in nature, while a third component is likely due to a superposition of multiple non‐ferroelectric processes. The proposed approach will enable deeper understanding of switching phenomena in weakly ferroelectric samples and materials with large chemo‐electromechanical response.

     
    more » « less
  4. Abstract

    Ferroelectric (FE) devices are conventionally switched by an application of an electric field. However, the recent discoveries of light–matter interactions in heterostructures based on 2D semiconductors and FE materials open new opportunities for using light as an additional tool for device programming. Recently, a purely optical switching of FE polarization in heterostructures comprising 2D MoS2and FE oxide perovskites, such as BaTiO3and Pb(Zr,Ti)O3(PZT), was demonstrated. In this work, it is investigated whether this optical switching has a practical value and can be used to improve functional characteristics of MoS2‐PZT FE field‐effect transistors for nonvolatile memory applications. It is demonstrated that the combined use of an electrical field and visible light improves the nonvolatile ON/OFF ratios in MoS2‐PZT memories by several orders of magnitude compared to their purely electrical operation. The memories are read at zero gate voltage (VG) in darkness, but their ON and OFF currents, which routinely varied for different devices by over 105, are achieved by programming at the sameVG = −6 V with (ON state) and without (OFF state) light illumination, demonstrating its crucial importance. The light can likely serve as an important tool for better programming of a large variety of other semiconductor‐FE devices.

     
    more » « less
  5. Abstract

    The Izu‐Bonin‐Mariana (IBM) fore arc preserves igneous rock assemblages that formed during subduction initiation circa 52 Ma. International Ocean Discovery Program (IODP) Expedition 352 cored four sites in the fore arc near the Ogasawara Plateau in order to document the magmatic response to subduction initiation and the physical, petrologic, and chemical stratigraphy of a nascent subduction zone. Two of these sites (U1440 and U1441) are underlain by fore‐arc basalt (FAB). FABs have mid‐ocean ridge basalt (MORB)‐like compositions, however, FAB are consistently lower in the high‐field strength elements (TiO2, P2O5, Zr) and Ni compared to MORB, with Na2O at the low end of the MORB field and FeO* at the high end. Almost all FABs are light rare earth element depleted, with low total REE, and have low ratios of highly incompatible to less incompatible elements (Ti/V, Zr/Y, Ce/Yb, and Zr/Sm) relative to MORB. Chemostratigraphic trends in Hole U1440B are consistent with the uppermost lavas forming off axis, whereas the lower lavas formed beneath a spreading center axis. Axial magma of U1440B becomes more fractionated upsection; overlying off‐axis magmas return to more primitive compositions. Melt models require a two‐stage process, with early garnet field melts extracted prior to later spinel field melts, with up to 23% melting to form the most depleted compositions. Mantle equilibration temperatures are higher than normal MORB (1,400 °C–1,480 °C) at relatively low pressures (1–2 GPa), which may reflect an influence of the Manus plume during subduction initiation. Our data support previous models of FAB origin by decompression melting but imply a source more depleted than normal MORB source mantle.

     
    more » « less