Lignin is an aromatic‐rich biomass polymer that is cheap, abundant, and sustainable. However, its application in the solid electrolyte field is rare due to challenges in well‐defined polymer synthesis. Herein, the synthesis of lignin‐graft‐poly(ethylene glycol) (PEG) and its conductivity test for a solid electrolyte application are demonstrated. The main steps of synthesis include functionalization of natural lignin's hydroxyl to alkene, followed by graft‐copolymerization of PEG thiol to the lignin via photoredox thiol‐ene reaction. Two lignin‐graft‐PEGs are prepared having 22 wt% lignin (lignin‐graft‐PEG 550) and 34 wt% lignin (lignin‐graft‐PEG 2000). Then, new polymer electrolytes for conductivity tests are prepared via addition of lithium bis‐trifluoromethanesulfonimide. The polymer graft electrolytes exhibit ionic conductivity up to 1.4 × 10−4 S cm−1 at 35 °C. The presence of lignin moderately impacts conductivity at elevated temperature compared to homopolymer PEG. Furthermore, the ionic conductivity of lignin‐graft‐PEG at ambient temperature is significantly higher than homopolymer PEG precedents.
- NSF-PAR ID:
- 10422084
- Date Published:
- Journal Name:
- Nanotechnology
- Volume:
- 34
- Issue:
- 12
- ISSN:
- 0957-4484
- Page Range / eLocation ID:
- 125602
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
Abstract -
Abstract Internal plasticization of poly(vinyl chloride) (PVC) was achieved in one‐step using copper‐mediated atom transfer radical polymerization to graft different ratios of random
n ‐butyl acrylate and 2–2‐(2‐ethoxyethoxy)ethyl acrylate copolymers from defect sites on the PVC chain. Five graft polymers were made with different ratios of poly(butyl acrylate) (PBA) and poly(2–2‐(2‐ethoxyethoxy)ethyl acrylate) (P2EEA); the glass transition temperatures (T g ) of functionalized PVC polymers range from − 25 to − 50°C. SingleT g values were observed for all polymers, indicating good compatibility between PVC and grafted chains, with no evidence of microphase separation. Plasticization efficiency is higher for polyether P2EEA moieties compared with PBA components. The resultant PVC graft copolymers are thermally more stable compared to unmodified PVC. Increasing the reaction scale from 2 to 14 g produces consistent and reproducible results, suggesting this method could be applicable on an industrial scale. -
Abstract Petrol and biochemical plasticizers are added to poly(vinyl alcohol) (PVA) to improve its processability while tuning its moisture sensitivity. But those additives often reduce the mechanical performance of PVA products. In this study, the antiplasticization and properties of PVA containing additives from biorenewable sources are studied. PVA fibers are gel‐spun having up to 3 wt% glucarate salts and 30% lignin. Glucarate lowers the gel melting temperature of PVA and increases fiber draw ratio. Further, glucarate enhances the mechanical performance of PVA beyond that of neat fibers. Interestingly, the combination of lignin and glucarate causes phase separation among fiber—a PVA/glucarate phase as the fiber core and lignin/PVA phase as the fiber shell. Neat PVA partially dissolves in 85 °C water; whereas, fibers containing glucarate and/or lignin resist dissolution. Thus, the combination of glucarate and lignin can induce high strength and moisture resistance, which are desirable industrial fiber properties.
-
Hierarchically microstructured tri-axial poly(vinyl alcohol)/graphene nanoplatelet (PVA/GNP) composite fibers were fabricated using a dry-jet wet spinning technique. The composites with distinct PVA/GNPs/PVA phases led to highly oriented and evenly distributed graphene nanoplatelets (GNPs) as a result of molecular chain-assisted interfacial exfoliation. With a concentration of 3.3 wt% continuously aligned GNPs, the composite achieved a ∼73.5% increase in Young's modulus (∼38 GPa), as compared to the pure PVA fiber, and an electrical conductivity of ∼0.38 S m −1 , one of the best mechanical/electrical properties reported for polymer/GNP nanocomposite fibers. This study has broader impacts on textile engineering, wearable robotics, smart sensors, and optoelectronic devices.more » « less
-
Abstract We report the structural and mechanical behavior of multicomponent hydrogels comprising the commercial poly(ethylene oxide)–poly(propylene oxide)–poly(ethylene oxide) block copolymer F127 and alginate. Previous studies on this system have shown thermoreversible behavior in shear rheology. Here we explore the properties of these materials under compression and large deformations, relevant to applications such as wound dressings that require mechanical robustness. For gels with lower F127 concentration, we find that the stiffness of the gels can be ascribed to the alginate network, and that the Young's modulus and fracture stress do not strongly depend on temperatures. However, for gels with an F127 concentration of 30 wt %, the Young's modulus is enhanced at higher temperatures. Under large deformations, the fracture stress and fracture strain of the materials can be independently varied using the alginate and F127 concentrations, respectively; without the trade‐off in these properties that is often observed in rigid polymer networks. Small‐angle X‐ray scattering shows a power‐law dependence scattering intensity on
q arising from the alginate network and scattering peaks consistent with rearranging micelles. For gels with lower F127 concentrations, we find a disordered–body‐centered cubic (BCC)‐face‐centered cubic (FCC) progression of states with temperature, and a BCC/FCC mixture for gels with higher F127 concentrations.