An official website of the United States government
The human sensorimotor system can adapt to various changes in the environmental dynamics by updating motor commands to improve performance after repeated exposure to the same task. However, the characteristics and mechanisms of the adaptation process remain unknown for dexterous manipulation, a unique motor task in which the body physically interacts with the environment with multiple effectors, i.e., digits, in parallel. We addressed this gap by using robotic manipulanda to investigate the changes in the digit force coordination following mechanical perturbation of an object held by tripod grasps. As the participants gradually adapted to lifting the object under perturbations, we quantified two components of digit force coordination. One is the direction-specific manipulation moment that directly counteracts the perturbation, whereas the other one is the direction-independent internal moment that supports the stability and stiffness of the grasp. We found that trial-to-trial improvement of task performance was associated with increased manipulation moment and a gradual decrease of the internal moment. These two moments were characterized by different rates of adaptation. We also examined how these two force coordination components respond to changes in perturbation directions. Importantly, we found that the manipulation moment was sensitive to the extent of repetitive exposure to the previous context that has an opposite perturbation direction, whereas the internal moment did not. However, the internal moment was sensitive to whether the postchange perturbation direction was previously experienced. Our results reveal, for the first time, that two distinct processes underlie the adaptation of multidigit force coordination for dexterous manipulation. NEW & NOTEWORTHY Changes in digit force coordination in multidigit object manipulation were quantified with a novel experimental design in which human participants adapted to mechanical perturbations applied to the object. Our results show that the adaptation of digit force coordination can be characterized by two distinct components that operate at different timescales. We further show that these two components respond to changes in perturbation direction differently.
more »
« less
Distinct sensorimotor mechanisms underlie the control of grasp and manipulation forces for dexterous manipulation
Abstract Dexterous manipulation relies on the ability to simultaneously attain two goals: controlling object position and orientation (pose) and preventing object slip. Although object manipulation has been extensively studied, most previous work has focused only on the control of digit forces for slip prevention. Therefore, it remains underexplored how humans coordinate digit forces to prevent object slip and control object pose simultaneously. We developed a dexterous manipulation task requiring subjects to grasp and lift a sensorized object using different grasp configurations while preventing it from tilting. We decomposed digit forces into manipulation and grasp forces for pose control and slip prevention, respectively. By separating biomechanically-obligatory from non-obligatory effects of grasp configuration, we found that subjects prioritized grasp stability over efficiency in grasp force control. Furthermore, grasp force was controlled in an anticipatory fashion at object lift onset, whereas manipulation force was modulated following acquisition of somatosensory and visual feedback of object’s dynamics throughout object lift. Mathematical modeling of feasible manipulation forces further confirmed that subjects could not accurately anticipate the required manipulation force prior to acquisition of sensory feedback. Our experimental approach and findings open new research avenues for investigating neural mechanisms underlying dexterous manipulation and biomedical applications.
more »
« less
- Award ID(s):
- 1827725
- PAR ID:
- 10435183
- Publisher / Repository:
- Nature Publishing Group
- Date Published:
- Journal Name:
- Scientific Reports
- Volume:
- 13
- Issue:
- 1
- ISSN:
- 2045-2322
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
null (Ed.)Abstract Successful object manipulation, such as preventing object roll, relies on the modulation of forces and centers of pressure (point of application of digits on each grasp surface) prior to lift onset to generate a compensatory torque. Whether or not generalization of learned manipulation can occur after adding or removing effectors is not known. We examined this by recruiting participants to perform lifts in unimanual and bimanual grasps and analyzed results before and after transfer. Our results show partial generalization of learned manipulation occurred when switching from a (1) unimanual to bimanual grasp regardless of object center of mass, and (2) bimanual to unimanual grasp when the center of mass was on the thumb side. Partial generalization was driven by the modulation of effectors’ center of pressure, in the appropriate direction but of insufficient magnitude, while load forces did not contribute to torque generation after transfer. In addition, we show that the combination of effector forces and centers of pressure in the generation of compensatory torque differ between unimanual and bimanual grasping. These findings highlight that (1) high-level representations of learned manipulation enable only partial learning transfer when adding or removing effectors, and (2) such partial generalization is mainly driven by modulation of effectors’ center of pressure.more » « less
-
Constraining contacts to remain fixed on an object during manipulation limits the potential workspace size, as motion is subject to the hand’s kinematic topology. Finger gaiting is one way to alleviate such restraints. It allows contacts to be freely broken and remade so as to operate on different manipulation manifolds. This capability, however, has traditionally been difficult or impossible to practically realize. A finger gaiting system must simultaneously plan for and control forces on the object while maintaining stability during contact switching. This letter alleviates the traditional requirement by taking advantage of system compliance, allowing the hand to more easily switch contacts while maintaining a stable grasp. Our method achieves complete SO(3) finger gaiting control of grasped objects against gravity by developing a manipulation planner that operates via orthogonal safe modes of a compliant, underactuated hand absent of tactile sensors or joint encoders. During manipulation, a low-latency 6D pose object tracker provides feedback via vision, allowing the planner to update its plan online so as to adaptively recover from trajectory deviations. The efficacy of this method is showcased by manipulating both convex and non-convex objects on a real robot. Its robustness is evaluated via perturbation rejection and long trajectory goals. To the best of the authors’ knowledge, this is the first work that has autonomously achieved full SO(3) control of objects within-hand via finger gaiting and without a support surface, elucidating a valuable step towards realizing true robot in-hand manipulation capabilities.more » « less
-
We consider the problem of in-hand dexterous manipulation with a focus on unknown or uncertain hand–object parameters, such as hand configuration, object pose within hand, and contact positions. In particular, in this work we formulate a generic framework for hand–object configuration estimation using underactuated hands as an example. Owing to the passive reconfigurability and the lack of encoders in the hand’s joints, it is challenging to estimate, plan, and actively control underactuated manipulation. By modeling the grasp constraints, we present a particle filter-based framework to estimate the hand configuration. Specifically, given an arbitrary grasp, we start by sampling a set of hand configuration hypotheses and then randomly manipulate the object within the hand. While observing the object’s movements as evidence using an external camera, which is not necessarily calibrated with the hand frame, our estimator calculates the likelihood of each hypothesis to iteratively estimate the hand configuration. Once converged, the estimator is used to track the hand configuration in real time for future manipulations. Thereafter, we develop an algorithm to precisely plan and control the underactuated manipulation to move the grasped object to desired poses. In contrast to most other dexterous manipulation approaches, our framework does not require any tactile sensing or joint encoders, and can directly operate on any novel objects, without requiring a model of the object a priori. We implemented our framework on both the Yale Model O hand and the Yale T42 hand. The results show that the estimation is accurate for different objects, and that the framework can be easily adapted across different underactuated hand models. In the end, we evaluated our planning and control algorithm with handwriting tasks, and demonstrated the effectiveness of the proposed framework.more » « less
-
This paper explores a novel approach to dexterous manipulation, aimed at levels of speed, precision, robustness, and simplicity suitable for practical deployment. The enabling technology is a Direct-drive Hand (DDHand) comprising two fingers, two DOFs each, that exhibit high speed and a light touch. The test application is the dexterous manipulation of three small and irregular parts, moving them to a grasp suitable for a subsequent assembly operation, regardless of initial presentation. We employed four primitive behaviors that use ground contact as a “third finger”, prior to or during the grasp process: pushing, pivoting, toppling, and squeeze- grasping. In our experiments, each part was presented from 30 to 90 times randomly positioned in each stable pose. Success rates varied from 83% to 100%. The time to manipulate and grasp was 6.32 seconds on average, varying from 2.07 to 16 seconds. In some cases, performance was robust, precise, and fast enough for practical applications, but in other cases, pose uncertainty required time-consuming vision and arm motions. The paper concludes with a discussion of further improvements required to make the primitives robust, eliminate uncertainty, and reduce this dependence on vision and arm motion.more » « less
