An official website of the United States government
Electrospray deposition (ESD) uses strong electric fields applied to solutions and dispersions exiting a capillary to produce charged monodisperse droplets driven toward grounded targets. Self‐limiting electrospray deposition (SLED) is a phenomenon in which highly directed, uniform, and even 3D coatings can be achieved by trapping charge in the deposited film, redirecting the field lines to uncoated regions of the target. However, when inorganic particles are added to SLED sprays, the buildup of charge required to repel incoming material is disrupted as particle loading increases. Due to its fibril gelling behavior, methylcellulose (MC) SLED can form nanowire morphologies. These wires, when used as a binder, can separate particles and prevent percolation. In this work, a variety of conductive and insulating particles are explored using patterned and un‐patterned substrates. This exploration allows us to maximally load particles for high‐concentration and highly controlled self‐limiting functional sprays. This is demonstrated using Ti3C2Tx MXene to functionalize an interdigitated electrode for use as a supercapacitor.
more »
« less
Microscale Templating of Materials across Electrospray Deposition Regimes
Electrospray deposition (ESD) uses strong electric fields to produce generations of monodisperse droplets from solutions and dispersions that are driven toward grounded substrates. When soft materials are delivered, the behavior of the growing film depends on the film’s ability to dissipate charge, which is strongly tied to its mobility for dielectric materials. Accordingly, there exist three regimes of electrospray: electrowetting, charged melt, and self-limiting. In the self-limiting regime, it has been recently shown that the targeted nature of these sprays allows for corona-free 3D coating. While ESD patterning on the micron-scale has been studied for decades, most typically through the use of insulating masks, there has been no comparative study of this phenomenon across spray regimes. Here, we used test-patterns composed of gratings that range in both feature size (30–240 μm) and spacing (⅓x–9x) to compare materials across regimes. The sprayed patterns were scanned using a profilometer, and the density, average height, and specificity were extracted. From these results, it was demonstrated that material deposited in the self-limiting regime showed the highest uniformity and specificity on small features as compared to electrowetting and charged melt sprays. Self-limiting electrospray deposition is, therefore, the best suited for modification of prefabricated electrode patterns.
more »
« less
- PAR ID:
- 10447256
- Date Published:
- Journal Name:
- Coatings
- Volume:
- 13
- Issue:
- 3
- ISSN:
- 2079-6412
- Page Range / eLocation ID:
- 599
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
null (Ed.)Abstract Electrospray deposition (ESD) applies a high voltage to liquids flowing through narrow capillaries to produce monodisperse generations of droplets down to hundreds of nanometers in diameter, each carrying a small amount of the delivered solute. This deposition method has been combined with insulated stencil masks for fabricating micropatterns by spraying solutions containing nanoparticles, polymers, or biomaterials. To optimize the fabrication process for micro-coatings, a self-limiting electrospray deposition (SLED) method has recently been developed. Here, we combine SLED with a pre-existing patterned polymer film to study SLED’s fundamental behavior in a bilayer geometry. SLED has been observed when glassy insulating materials are sprayed onto conductive substrates, where a thickness-limited film forms as charge accumulates and repels the arrival of additional charged droplets. In this study, polystyrene (PS), Parylene C, and SU-8 thin films of varying thickness on silicon are utilized as insulated spraying substrates. Polyvinylpyrrolidone (PVP), a thermoplastic polymer is sprayed below its glass transition temperature (T g ) to investigate the SLED behavior on the pre-deposited insulating films. Furthermore, to examine the effects of in-plane confinement on the spray, a microhole array patterned onto the PS thin film by laser dewetting was sprayed with dyed PVP in the SLED mode. This was then extended to an unmasked electrode array showing that masked SLED and laser dewetting could be used to target microscale regions of conventionally-patterned electronics.more » « less
-
Paul B. Tchounwou (Ed.)Abstract: The COVID-19 pandemic has resulted in high demand for disinfection technologies. However, the corresponding spray technologies are still not completely optimized for disinfection purposes. There are important problems, like the irregular coverage and dripping of disinfectant solutions on hard and vertical surfaces. In this study, we highlight two major points. Firstly, we discuss the effectiveness of the electrostatic spray deposition (ESD) of nanoparticle-based disinfectant solutions for systematic and long-lasting disinfection. Secondly, we show that, based on the type of material of the substrate, the effectiveness of ESD varies. Accordingly, 12 frequently touched surface materials were sprayed using a range of electrostatic spray system parameters, including ion generator voltage, nozzle spray size and distance of spray. It was observed that for most cases, the surfaces become completely covered with the nanoparticles within 10 s. Acrylic, Teflon, PVC, and polypropylene surfaces show a distinct effect of ESD and non-ESD sprays. The nanoparticles form a uniform layer with better surface coverage in case of electrostatic deposition. Quantitative variations and correlations show that 1.5 feet of working distance, an 80 μm spray nozzle diameter and an ion generator voltage of 3–7 kV ensures a DEF (differential electric field) that corresponds to an optimized charge-to-mass ratio, ensuring efficient coverage of nanoparticles.more » « less
-
Multilayer polymer films are extensively used in multiphase separation. Electrospray deposition (ESD) is an important technique for fabricating such films with tunable morphology. Viscoelastic properties of polystyrene (PS) nanoshell coatings produced by ESD on gold and spin‐coated PS surfaces are evaluated using Quartz Crystal Microbalance with Dissipation (QCM‐D). The thickness of PS films on gold increases with flow rate from ∼200 nm at 0.5 to ∼400 nm at 1.5 mL h^−1, accompanied by an order‐of‐magnitude increase in dissipation due to larger particle sizes from shorter droplet flight times. This effect is absent on spin–coated PS films, suggesting the onset of the self‐limiting effect of charges. Although the shear moduli for ESD films calculated from Voigt models is only 0.08%–0.20% of the bulk PS modulus, the stiffness ratio of spray‐coated PS to a single shell is (5.00–13.3) × 10^3 m^−1, due to shell–shell and shell–substrate interactions. These are novel results related to the interparticle friction obtained using QCM‐D for the first time. This work demonstrates that mechanical properties of particulate viscoelastic films with potential applications in high surface area sensors, such as size‐selective membranes for protein or electrolyte adsorption, can be evaluated by QCM‐D with nanograms of material.more » « less
-
Electrospray deposition (ESD) is employed to produce separator membranes for coin-cell lithium-ion batteries (LIBs) using off-the-shelf polyimide (PI). The PI coatings are deposited directly onto planar LiNi0.6Mn0.2Co0.2O2 (NMC) electrodes via self-limiting electrospray deposition (SLED). Scanning electron microscopy (SEM), optical microscopy, and spectroscopic microreflectometry are implemented in combination to evaluate the porosity, thickness, and morphology of sprayed PI films. Furthermore, ultraviolet-visual wavelength spectroscopy (UV vis) is utilized to qualitatively assess variation in film porosity within a temperature range of 20-400oC, to determine the stable temperature range of the separator. UV vis results underscore the ability of the SLED PI separator to maintain its porous microstructure up to ~350oC. Electrochemical performance of the PI separators is analyzed via charge/discharge cycle rate tests. Discharge capacities of the SLED PI separators are within 83-99.8% of commercial Celgard 2325 PP/PE/PP separators. This study points to the unique possibility of SLED as a separator manufacturing technique for geometrically complex energy storage systems. Further research is needed to optimize the polymer-solvent system to enhance control of porosity, pore size, and coating thickness. This can lead to significant improvement in rate and cycle life performance in more advanced energy storage devices.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.3390/coatings13030599
