This work investigated material extrusion additive manufacturing (MatEx AM) of specialized fluoroelastomer (FKM) compounds for applications in rubber seals and gaskets. The influence of a commercially available perfluoropolyether (PFPE) plasticizer on the printability of a control FKM rubber compound was studied using a custom-designed ram material extruder, Additive Ram Material Extruder (ARME), for printing fully compounded thermoset elastomers. The plasticizer’s effectiveness was assessed based on its ability to address challenges such as high compound viscosity and post-print shrinkage, as well as its impact on interlayer adhesion. The addition of the PFPE plasticizer significantly reduced the FKM compound’s viscosity (by 70%) and post-print shrinkage (by 65%). While the addition of the plasticizer decreased the tensile strength of the control compound, specimens printed with the plasticized FKM retained 34% of the tensile strength of compression-molded samples, compared to only 23% for the unplasticized compound. Finally, the feasibility of seals and gaskets manufacturing using both conventional and unconventional additive manufacturing (AM) approaches was explored. A hybrid method combining AM and soft tooling for compression molding emerged as the optimal method for seal and gasket fabrication.
A ram extruder is described for high‐pressure extrusion of fully compounded thermoset rubber to achieve additive manufacturing. The extruder uses a piston driven by a geared stepper motor to provide volumetric displacement of the rubber charge residing in a temperature‐controlled barrel. Along with activators, accelerators, and a vulcanizing agent, the rubber compound is a formulation of 30 parts carbon black per hundred parts nitrile rubber. Sets of serpentine patterns are printed in parallel and transverse orientations relative to the load direction. From printing to post‐cure, the printed specimens exhibited linear shrinkage of 65% in the print direction. Although printed samples had relatively low void content compared with typical additively manufactured parts by material extrusion, significant decreases in the tensile properties were observed relative to compression‐molded specimens of the same rubber compound. The mean strain to failure was observed as 462% for compression‐molded samples, compared with 347% and 183% for printed specimens with parallel and transverse orientations. To reduce the shrinkage and increase the interfacial area between extruded roads, backstitch and sinewave diddling patterns were implemented to superimpose oscillatory motions along the print path with a periodicity of 1 mm. The specimens printed with the diddling patterns were observed to provide less shrinkage and improved properties compared to the regular serpentine patterns. The mean strain to failure in the transverse orientation, respectively, increased to 218% and 265% for the backstitch and sinewave patterns. Suggested future research is discussed, and the diddling program is provided in the appendix.
more » « less- Award ID(s):
- 1822147
- NSF-PAR ID:
- 10448049
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Polymer Composites
- Volume:
- 42
- Issue:
- 10
- ISSN:
- 0272-8397
- Page Range / eLocation ID:
- p. 5237-5248
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
-
more » « less
This paper analyzes the effect of print layer heights and loading direction on the compressive response of plain and fiber-reinforced (steel or basalt fiber) 3D printed concrete. Slabs with three different layer heights (6, 13, and 20 mm) are printed, and extracted cubes are subjected to compression (i) along the direction of printing, (ii) along the direction of layer build-up, and (iii) perpendicular to the above two directions. Digital image correlation (DIC) is used as a non-contact means to acquire the strain profiles. While the 3D printed specimens show lower strengths, as compared to cast specimens, when tested in all three directions, this effect can be reduced through the use of fiber reinforcement. Peak stress and peak strain-based anisotropy coefficients, which are linearly related, are used to characterize and quantify the directional dependence of peak stress and strain. Interface-parallel cracking is found to be the major failure mechanism, and anisotropy coefficients increase with an increase in layer height, which is attributable to the increasing significance of interfacial defects. Thus, orienting the weaker interfaces appropriately, through changes in printing direction, or strengthening them through material modifications (such as fiber reinforcement) or process changes (lower layer height, enables attainment of near-isotropy in 3D printed concrete elements.
-
Composites printed using material extrusion additive manufacturing (AM) typically exhibit alignment of high- aspect-ratio reinforcements parallel to the print direction. This alignment leads to highly anisotropic stiffness, strength, and transport properties. In many cases, it would be desirable to increase mechanical and transport properties transverse to the print direction, for example, in 3D-printed heat sinks or heat exchangers where heat must be moved efficiently between printed roads or layers. Rotational direct ink writing (RDIW), where the deposition nozzle simultaneously rotates and translates during deposition, provides a method to reorient fibers transverse to the print direction during the printing process. In the present work, carbon fiber-reinforced epoxy composites were printed by RDIW with a range of nozzle rotation rates and the in-plane and through-thickness thermal conductivity was measured. In addition, the orientation of carbon fiber (CF) in the composites was measured using optical microscopy and image analysis, from which second-order fiber orientation tensors were calculated. These results showed that the orientation of CF became less anisotropic as nozzle rotation rate increased, leading to increased through-thickness thermal conductivity, which increased by 40% at the highest rotation rate. The orientation tensors also showed that RDIW was more effective at reorienting fibers within the in-plane transverse direction compared to the through-thickness transverse direction. The results presented here demonstrate that a current weakness of material extrusion AM composites—poor thermal conductivity in the through-thickness direction—can be significantly improved with RDIW.more » « less
-
more » « less
Magnetic Field Assisted Additive Manufacturing (MFAAM), 3D printing in a magnetic field, has the potential to fabricate high magnetic strength anisotropic bonded magnets. Here, 10, 35, and 54 wt% strontium ferrite bonded magnets using polyamide 12 binder were developed by twin screw compounding process and then printed via MFAAM samples in zero, and in 0.5 Tesla (H parallel to the print direction and print bed). The hysteresis curves were measured using a MicroSense EZ9 Vibrating Sample Magnetometer (VSM) for 3 different mount orientations of the sample on the sample holder to explore the magnetic anisotropy. The samples printed in zero field exhibited a weak anisotropy with an easy axis perpendicular to the print direction. This anisotropy is caused by the effect of shear flow on the orientation of the magnetic platelets in the 3D printer head. For the MFAAM samples, the S values are largest along the print bed normal. This anisotropy is caused by the field. The alignment of the magnetic particles happens when the molten suspension is in the extruder. When the material is printed, it is folded over on the print bed and its easy axis rotates 90° parallel to the print bed normally. Little realignment of the particles happens after it is printed, suggesting a sharp drop in temperature once the composite touches the print bed, indicating that field-induced effects in the nozzle dominate the anisotropy of MFAAM deposited samples.
-
Polypropylene block copolymer (PPco) is easier to process in extrusion-based additive manufacturing compared to isotactic PP homopolymer because it shrinks and warps less during printing. This study investigated the thermal properties of PPco and spray-dried CNF (SDCNF)-PPco composite pellet formulations. Thermogravimetric analysis data showed that the addition of SDCNF lowered the thermal degradation onset temperature and increased the residual mass content (at 450 C) of PPco pellets. The peak degradation temperatures of SDCNF and PPco remained the same. The peak crystallization temperature and relative crystallinity of PPco were increased by the addition of SDCNF and MAPP. The peak melting temperature of PPco was not significantly changed. Printed specimens showed three melting peaks (b, b0 and a crystals) while injection molded PPco only showed one (a crystal) melting peak. Dynamic mechanical analysis results showed that the heat deflection temperatures of printed SDCNF-PPco composites were higher than injection molded PPco. SEM micrographs showed that the addition of SDCNF increased the number of voids inside the printed parts.more » « less
