More Like this

1. Laboratory Evidence of Transient Pressure Surge in a Fluid-Filled Fracture as a Potential Driver of Remote Dynamic Earthquake Triggering

   https://doi.org/10.1785/0320210015  

   Jin, Yuesu; Dyaur, Nikolay; Zheng, Yingcai (July 2021, The Seismic Record)

   null (Ed.)

   Abstract Seismic waves carrying tiny perturbing stresses can trigger earthquakes in geothermal and volcanic regions. The underlying cause of this dynamic triggering is still not well understood. One leading hypothesis is that a sudden increase in the fluid-pore pressure in the fault zone is involved, but the exact physical mechanism is unclear. Here, we report experimental evidence in which a fluid-filled fracture was shown to be able to amplify the pressure of an incoming seismic wave. We built miniature pressure sensors and directly placed them inside a thin fluid-filled fracture to measure the fluid pressure during wave propagation. By varying the fracture aperture from 0.2 to 9.2 mm and sweeping the frequency from 12 to 70 Hz, we observed in the lab that the fluid pressure in the fracture could be amplified up to 25.2 times compared with the incident-wave amplitude. Because an increase of the fluid pressure in a fault can reduce the effective normal stress to allow the fault to slide, our observed transient pressure surge phenomenon may provide the mechanism for earthquake dynamic triggering. 

   more » « less
2. Evolution of Fault-Zone Hydromechanical Properties in Response to Different Cementation Processes

   https://doi.org/10.2113/2022/1069843  

   Romano, C. R.; Williams, R. T.; Cheng, ed., Feng (January 2022, Lithosphere)

   Abstract Progressive cementation and sealing of fault-localized fractures impact crustal mass transport and the recovery of fault strength following slip events. We use discrete fracture network (DFN) models to examine how fracture sealing during end-member cementation mechanisms (i.e., reaction- versus transported-limited cementation) influences the partitioning of fluid flow through time. DfnWorks was used to generate randomized fracture networks parameterized with fracture orientation data compiled from field studies. Single-phase flow simulations were performed for each network over a series of timesteps, and network parameters were modified to reflect progressive fracture sealing consistent with either reaction- or transport-limited crystal growth. Results show that when fracture cementation is reaction-limited, fluid flow becomes progressively channelized into a smaller number of fractures with larger apertures. When fracture cementation is transport-limited, fluid flow experiences progressive dechannelization, becoming more homogeneously distributed throughout the fracture network. These behaviors are observed regardless of the DFN parameterization, suggesting that the effect is an intrinsic component of all fracture networks subjected to the end-member cementation mechanisms. These results have first-order implications for the spatial distribution of fluid flow in fractured rocks and recovery of permeability and strength during fault/fracture healing in the immediate aftermath of fault slip. 

   more » « less
3. Distributed Acoustic Sensing as a Distributed Hydraulic Sensor in Fractured Bedrock

   https://doi.org/10.1029/2020WR028140  

   Becker, M. W.; Coleman, T. I.; Ciervo, C. C. (August 2020, Water Resources Research)

   Abstract Distributed acoustic sensing (DAS) was originally intended to measure oscillatory strain at frequencies of 1 Hz or more on a fiber optic cable. Recently, measurements at much lower frequencies have opened the possibility of using DAS as a dynamic strain sensor in boreholes. A fiber optic cable mechanically coupled to a geologic formation will strain in response to hydraulic stresses in pores and fractures. A DAS interrogator can measure dynamic strain in the borehole, which can be related to fluid pressure through the mechanical compliance properties of the formation. Because DAS makes distributed measurements, it is capable of both locating hydraulically active features and quantifying the fluid pressure in the formation. We present field experiments in which a fiber optic cable was mechanically coupled to two crystalline rock boreholes. The formation was stressed hydraulically at another well using alternating injection and pumping. The DAS instrument measured oscillating strain at the location of a fracture zone known to be hydraulically active. Rock displacements of less than 1 nm were measured. Laboratory experiments confirm that displacement is measured correctly. These results suggest that fiber optic cable embedded in geologic formations may be used to map hydraulic connections in three‐dimensional fracture networks. A great advantage of this approach is that strain, an indirect measure of hydraulic stress, can be measured without beforehand knowledge of flowing fractures that intersect boreholes. The technology has obvious applications in water resources, geothermal energy, CO₂sequestration, and remediation of groundwater in fractured bedrock. 

   more » « less
4. Dispersion of solids in fracturing flows of yield stress fluids

   https://doi.org/10.1017/jfm.2017.465  

   Hormozi, S.; Frigaard, I. A. (November 2017, Journal of Fluid Mechanics)

   Solids dispersion is an important part of hydraulic fracturing, both in helping to understand phenomena such as tip screen-out and spreading of the pad, and in new process variations such as cyclic pumping of proppant. Whereas many frac fluids have low viscosity, e.g. slickwater, others transport proppant through increased viscosity. In this context, one method for influencing both dispersion and solids-carrying capacity is to use a yield stress fluid as the frac fluid. We propose a model framework for this scenario and analyse one of the simplifications. A key effect of including a yield stress is to focus high shear rates near the fracture walls. In typical fracturing flows this results in a large variation in shear rates across the fracture. In using shear-thinning viscous frac fluids, flows may vary significantly on the particle scale, from Stokesian behaviour to inertial behaviour across the width of the fracture. Equally, according to the flow rates, Hele-Shaw style models give way at higher Reynolds number to those in which inertia must be considered. We develop a model framework able to include this range of flows, while still representing a significant simplification over fully three-dimensional computations. In relatively straight fractures and for fluids of moderate rheology, this simplifies into a one-dimensional model that predicts the solids concentration along a streamline within the fracture. We use this model to make estimates of the streamwise dispersion in various relevant scenarios. This model framework also predicts the transverse distributions of the solid volume fraction and velocity profiles as well as their evolutions along the flow part. 

   more » « less
5. Dissolved gas recovery from water using a sidestream hollow-fiber membrane module: First principles model synthesis and steady-state validation

   https://doi.org/10.1016/j.memsci.2023.122134  

   Song, I; Soulia, PS; Novak, PJ; Arnold, WA; Wright, NC (October 2023, Journal of Membrane Science)

   This paper presents a first-principles model for the recovery of dissolved gases from liquids using a sidestream hollow-fiber membrane module. The model avoids the use of new empirical coefficients, thus providing a parametric understanding of the process behavior for future design and optimization of membrane modules. This type of first-principles model could be particularly useful when gas recovery is beneficial to biological or chemical reactions of interest, such as the acetogenesis reactions in two-stage anaerobic digesters. The steady-state behavior of the model was validated against both new experimental data for the recovery of H2, CH4 and H2–CH4 mixtures from pure water, as well as existing published data. The modeled gas recovery predictions agreed with experimental data to an absolute average error of 13%, and an average R value of 0.98. Parametric analysis of mixed-gas recovery suggests possible key transition points in the composition of the recovered gases. For example, at 40 °C, increasing trans-membrane pressure while keeping hydraulic residence time (HRT) under 0.5 s will result in an increase in the ratio of H2 to CH4 recovered. Otherwise, increasing trans-membrane pressure will instead decrease the ratio of H2 to CH4 recovered. The model has potential to be extended to transient analysis, but has yet to be validated with transient experimental data. This model was successfully implemented in both Python and MATLAB, and provides valuable insights for future net-energy optimization for anaerobic digestion systems with in-situ gas recovery. 

   more » « less