Here, a novel melt electrospinning method to produce few‐micron and nanometer thick fibers is presented, in which a polymer‐coated wire with a sharp tip is used as the polymer source. The polymer coating is melted via Joule heating of the source wire and extracted toward the target via electrostatic forces. The high viscosity and low charge density of polymer melts lower their stretchability in melt. The method relies on confining the Taylor cone and reducing initial jet diameter via concentrated electrostatic fields as a means to reduce the diameter of fibers. As a result, the initial jet diameter and the final fiber diameter are reduced by an order of magnitude of three to ten times, respectively, using wire melt electrospinning compared to syringe‐ and edge‐based electrospinning. The fiber diameter melt electrospun via this novel method is 1.0 ± 0.9 µm, considerably thinner than conventional melt electrospinning techniques. The generation of thin fibers are explained in terms of the electrostatic field around the wire tip, as obtained from finite element analysis (FEA), which controls the size and shape of the melt electrospun jet.
Electrospinning is commonly used for fabrication of polymer fibers. Melt electrospinning, instead of the commonly used solution electrospinning, offers many advantages in generating polymer fibers without using solvents. However, polymer melts have high viscosity which poses major limitations in producing low diameter fibers. Here, melt electrospinning is investigated at elevated temperatures in inert atmosphere to reduce fiber diameters while suppressing thermal degradation. Two types of spinneret configurations, syringe and wire, with two distinct outcomes are studied. In syringe‐based electrospinning, increasing the nozzle temperature from 300 to 360 °C in nitrogen reduced fiber diameter significantly from 33 ± 5 to 10 ± 4 µm. Electrospinning in nitrogen leads to formation of fibers even at a high nozzle temperature of 360 °C, while this temperature leads to thermal degradation when spinning in air. In contrast, increasing the temperature of wire electrospinning setup do not lead to a noticeable reduction in diameter. This is attributed to the viscosity‐dependent flow rate in this method. Increasing the temperature leads to increased flow rates, promoting the formation of thicker fibers, while the increased stretchability promotes the formation of thinner fibers. The results clearly demonstrate advantages of developing polymer microfibers in inert atmosphere to avoid thermal degradation with a temperature‐independent flow control.
more » « less- PAR ID:
- 10455058
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Macromolecular Materials and Engineering
- Volume:
- 305
- Issue:
- 12
- ISSN:
- 1438-7492
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
Abstract -
null (Ed.)Cholesteryl ester liquid crystals exhibit thermochromic properties related to the existence of a twisted nematic phase. We formulate ternary mixtures of cholesteryl benzoate (CB), cholesteryl pelargonate (CP), and cholesteryl oleyl carbonate (COC) to achieve thermochromic behavior. We aim to achieve thermochromic fibers by incorporating the liquid crystal formulations into electrospun fibers. Two methods of incorporating the liquid crystal (LC) are compared: (1) blend electrospinning and (2) coaxial electrospinning using the same solvent system for the liquid crystal. For blend electrospinning, intermolecular interactions seem to be important in facilitating fiber formation since addition of LC can suppress bead formation. Coaxial electrospinning produces fibers with higher nominal fiber production rates (g/hr) and with higher nominal LC content in the fiber (wt. LC/wt. polymer assuming all of the solvent evaporates) but larger fiber size distributions as quantified by the coefficient of variation in fiber diameter than blend electrospinning with a single nozzle. Importantly, our proof-of-concept experiments demonstrate that coaxially electrospinning with LC and solvent in the core preserves the thermochromic properties of the LC so that thermochromic fibers are achieved.more » « less
-
Fibrous shape memory polymers (SMPs) have received growing interest in various applications, especially in biomedical applications, which offer new structures at the microscopic level and the potential of enhanced shape deformation of SMPs. In this paper, we report on the development and investigation of the properties of acrylate-based shape memory polymer fibers, fabricated by electrospinning technology with the addition of polystyrene (PS). Fibers with different diameters are manufactured using four different PS solution concentrations (25, 30, 35, and 40 wt%) and three flow rates (1.0, 2.5, and 5.0 μL min −1 ) with a 25 kV applied voltage and 17 cm electrospinning distance. Scanning electron microscope (SEM) images reveal that the average fiber diameter varies with polymer concentration and flow rates, ranging from 0.655 ± 0.376 to 4.975 ± 1.634 μm. Dynamic mechanical analysis (DMA) and stress–strain testing present that the glass transition temperature and tensile values are affected by fiber diameter distribution. The cyclic bending test directly proves that the electrospun SMP fiber webs are able to fully recover; additionally, the recovery speed is also affected by fiber diameter. With the combination of the SMP material and electrospinning technology, this work paves the way in designing and optimizing future SMP fibers properties by adjusting the fiber diameter.more » « less
-
more » « less
Abstract The covid‐19 pandemic has revealed the need for alternative production approaches with low startup costs like electrospinning for filter needs, the most imperative element of the personal protective equipment (PPE). Current attempts in advancing melt electrospinning deal with developing strategies for fiber diameter attenuation toward sub‐micron scale. Here, the attunement in the spinning‐zone temperature known as ''spin‐line temperature profile'' was utilized as a baseline for fiber diameter reduction. The mechanical performance of the melt‐electrospun linear low‐density polyethylene (LLDPE) fibers is reported to characterize their structural transformation with respect to various spin‐line temperature profiles. With an increase in the spin‐line temperature to above 100°C in the area of cone formation, an increased tensile and yield strength along with fiber diameter reduction by four‐folds was demonstrated. A significant increase in toughness, by almost three times, without compromising the stiffness and Young's modulus was observed. The dynamic mechanical analysis revealed that spinning in high temperatures produces changes in the alpha (α) relaxation, contributing to the significant increase in strain at break. These results are significant because polyolefin fibers are an imperative element of medical textiles and PPE. Therefore, developing a correlation for process‐structure‐properties for emerging production techniques like melt electrospinning becomes critical.
-
Polyethylene melt conductivity was increased by adding a commercial anti-static agent, which resulted in a 20× decrease in electrospun fiber diameter and formation of a significant fraction of sub-micron diameter fibers. Two polyethylene formulations and varying additive concentrations were utilized to span the parameter space of conductivity and viscosity. The key role of conductivity in determining the jet radius (which sets the upper limit on the fiber size) is discussed in the context of fluid mechanics theory and previous simulations. Parameters which affect the conversion of the liquid jet to a solid fiber and the pertinent theory are outlined. An “unconfined” experimental configuration is utilized to both avoid potential needle clogging and enable direct observation of important characteristic length scales related to the interaction of the fluid and the applied electric field. In this approach, the fluid spontaneously forms an array of cone perturbations which act as stationary “nozzles” through which the mobile fluid flows to form the jet. The experimental data and theory considerations allow for a holistic discussion of the interaction between flow rate, viscosity, conductivity, and the resultant jet and fiber size. Information about the fluid viscosity and conductivity gained by observing the electrospinning process is highlighted. Schemes for theoretically predicting the cone-jet density, cone size, and flow rate are compared to experimental results.more » « less
