The development of high voltage solar cells is an attractive way to use sunlight for solar‐to‐fuel devices, multijunction solar‐to‐electric systems, and to power limited‐area consumer electronics. By designing a low‐oxidation‐potential organic dye (
Sequential series multijunction dye‐sensitized solar cells (SSM‐DSCs) can power solar‐to‐fuel processes with a single illuminated area device. Dye selection and strategies limiting photon losses are critical in SSM‐DSC devices for higher performance systems. Herein, an efficient and readily applicable spin coating protocol on glass surfaces with an antireflective fluoropolymer (CYTOP) is applied to an SSM‐DSC architecture. Combining CYTOP with the use of an immersion oil between glass spacers in a three subcell SSM‐DSC with judiciously selected TiO2photoanode sensitizers and thicknesses, an overall power conversion efficiency (PCE) of 10.1% is obtained with an output of 2.3 V. Without external bias, this SSM‐DSC configuration shows an impressive overall solar‐to‐fuel conversion efficiency of 6% when powering IrO2and Au2O3electrocatalysts for CO2and H2O to CO and H2conversion in aqueous solution. The role of CYTOP, immersion oil, sensitizer selection, and film thickness on SSM‐DSC devices is discussed along with the stability of this system.
more » « less- NSF-PAR ID:
- 10461188
- Publisher / Repository:
- Wiley Blackwell (John Wiley & Sons)
- Date Published:
- Journal Name:
- Advanced Energy Materials
- Volume:
- 9
- Issue:
- 15
- ISSN:
- 1614-6832
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
Abstract RR9 )/redox shuttle (Fe(bpy)33+/2+) pair for dye‐sensitized solar‐cell (DSSC) devices, the highest single device photovoltage (1.42 V) has been realized for a DSSC not relying on doped TiO2. Additionally, Fe(bpy)33+/2+offers a robust, readily tunable ligand platform for redox potential tuning.RR9 can be regenerated with a low driving force (190 mV), and by utilizing theRR9 /Fe(bpy)33+/2+redox shuttle pair in a subcell for a sequential series multijunction (SSM)‐DSSC system, one of the highest known three subcell photovoltage was attained for any solar‐cell technology (3.34 V, >1.0 V per subcell). -
Three copper redox shuttles ([Cu( 1 )] 2+/1+ , [Cu( 2 )] 2+/1+ , and [Cu( 3 )] 2+/1+ ) featuring tetradentate ligands were synthesized and evaluated computationally, electrochemically, and in dye-sensitized solar cell (DSC) devices using a benchmark organic dye, Y123 . Neutral polyaromatic ligands with limited flexibility were targeted as a strategy to improve solar-to-electrical energy conversion by reducing voltage losses associated with redox shuttle electron transfer events. Inner-sphere electron transfer reorganization energies ( λ ) were computed quantum chemically and compared to the commonly used [Co(bpy) 3 ] 3+/2+ redox shuttle which has a reported λ value of 0.61 eV. The geometrically constrained biphenyl-based Cu redox shuttles investigated here have lower reorganization energies (0.34–0.53 eV) and thus can potentially operate with lower driving forces for dye regeneration (Δ G reg ) in DSC devices when compared to [Co(bpy) 3 ] 3+/2+ -based devices. The rigid tetradentate ligand design promotes more efficient electron transfer reactions leading to an improved J SC (14.1 mA cm −2 ), higher stability due to the chelate effect, and a decrease in V lossOC for one of the copper redox shuttle-based devices.more » « less
-
more » « less
Improving efficiency and stability has become an urgent issue in the application of perovskite solar cells (PSCs). Herein, a kind of long‐chain polymer or polymethylmethacrylate (PMMA) is added into the spiro‐OMeTAD matrix to improve the film formation process and hence the device performance. It is observed that, after modification, the spiro‐OMeTAD‐based hole‐transporting layer becomes uniform, continuous, and condensed. Meanwhile, the power conversion efficiency of the devices is upgraded. Compared with the control device, open‐circuit voltage of the modified one (with moderate doping) increases from 1.06 (±0.03) to 1.10 (±0.02) V, fill factor increases from 72.20 (±3.44)% to 75.59 (±3.35)%, and the power conversion efficiency increases from 18.82 (±1.06)% to 20.51 (±0.82)% (highest at 21.78%) under standard test condition (AM 1.5G, 100 mW cm−2). Transient photocurrent/photovoltage decay curves, time‐resolved photoluminance, and impedance spectroscopy studies show that the modification could accelerate charge transfer and retard interfacial recombination. In addition, the modification improves device stability. Due to the strengthened barrier against penetration of “H2O/O2/Ag,” the efficiency of the unsealed device could retain 91.49% (by average) of the initial one after 100 days storage in the dark [relative humidity = 30(±5)%]. This work shows that long‐chain polymer doping could simultaneously improve efficiency and stability of spiro‐OMeTAD‐based PSCs.
-
more » « less
Abstract Photocatalytic CO2reduction with water to hydrocarbons represents a viable and sustainable process toward greenhouse gas reduction and fuel/chemical production. Development of more efficient catalysts is the key to mitigate the limits in photocatalytic processes. Here, a novel ultrathin‐film photocatalytic light absorber (UFPLA) with TiO2films to design efficient photocatalytic CO2conversion processes is created. The UFPLA structure conquers the intrinsic trade‐off between optical absorption and charge carrier extraction efficiency, that is, a solar absorber should be thick enough to absorb majority of the light allowable by its bandgap but thin enough to allow charge carrier extraction for reactions. The as‐obtained structures significantly improve TiO2photocatalytic activity and selectivity to oxygenated hydrocarbons than the benchmark photocatalyst (Aeroxide P25). Remarkably, UFPLAs with 2‐nm‐thick TiO2films result in hydrocarbon formation rates of 0.967 mmol g−1h−1, corresponding to 1145 times higher activity than Aeroxide P25. This observation is confirmed by femtosecond transient absorption spectroscopic experiments where longer charge carrier lifetimes are recorded for the thinner films. The current work demonstrates a powerful strategy to control light absorption and catalysis in CO2conversion and, therefore, creates new and transformative ways of converting solar energy and greenhouse gas to alcohol fuels/chemicals.
-
more » « less
Abstract Anthropogenic carbon dioxide (CO2) release in the atmosphere from fossil fuel combustion has inspired scientists to study CO2to biofuel conversion. Oxygenic phototrophs such as cyanobacteria have been used to produce biofuels using CO2. However, oxygen generation during oxygenic photosynthesis adversely affects biofuel production efficiency. To produce
n -butanol (biofuel) from CO2, here we introduce ann -butanol biosynthesis pathway into an anoxygenic (non-oxygen evolving) photoautotroph,Rhodopseudomonas palustris TIE-1 (TIE-1). Using different carbon, nitrogen, and electron sources, we achieven -butanol production in wild-type TIE-1 and mutants lacking electron-consuming (nitrogen-fixing) or acetyl-CoA-consuming (polyhydroxybutyrate and glycogen synthesis) pathways. The mutant lacking the nitrogen-fixing pathway produce the highestn -butanol. Coupled with novel hybrid bioelectrochemical platforms, this mutant producesn -butanol using CO2, solar panel-generated electricity, and light with high electrical energy conversion efficiency. Overall, this approach showcases TIE-1 as an attractive microbial chassis for carbon-neutraln- butanol bioproduction using sustainable, renewable, and abundant resources.
