Phyllosilicates weaken faults due to the formation of shear fabrics. Although the impacts of clay abundance and fabric on frictional strength, sliding stability, and porosity of faults are well studied, their influence on elastic properties is less known, though they are key factors for fault stiffness. We document the role that fabric and consolidation play in elastic properties and show that smectite content is the most important factor determining whether fabric or porosity controls the elastic response of faults. We conducted a suite of shear experiments on synthetic smectite‐quartz fault gouges (10–100 wt% smectite) and sediment incoming to the Sumatra subduction zone. We monitored
- Award ID(s):
- 1822214
- NSF-PAR ID:
- 10463569
- Date Published:
- Journal Name:
- Nature Communications
- Volume:
- 13
- Issue:
- 1
- ISSN:
- 2041-1723
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
Abstract Vp ,Vs , friction, porosity, shear and bulk moduli. We find that mechanical and elastic properties for gouges with abundant smectite are almost entirely controlled by fabric formation (decreasing mechanical and elastic properties with shear). Though fabrics control the elastic response of smectite‐poor gouges over intermediate shear strains, porosity is the primary control throughout the majority of shearing. Elastic properties vary systematically with smectite content: High smectite gouges have values ofVp ~ 1,300–1,800 m/s,Vs ~ 900–1,100 m/s,K ~ 1–4 GPa, andG ~ 1–2 GPa, and low smectite gouges have values ofVp ~ 2,300–2,500 m/s,Vs ~ 1,200–1,300 m/s,K ~ 5–8 GPa, andG ~ 2.5–3 GPa. We find that, even in smectite‐poor gouges, shear fabric also affects stiffness and elastic moduli, implying that while smectite abundance plays a clear role in controlling gouge properties, other fine‐grained and platy clay minerals may produce similar behavior through their control on the development of fabrics and thin shear surfaces. -
more » « less
Abstract During rock friction experiments at large displacement, room temperature and humidity, and following a hold test, the fracture energy increases approximately as the square of the logarithm of hold duration. While it's been long known that failure strength increases with log hold time, here the slip weakening distance,
d h , also increases. The weakening distance increase is large, hundreds of percent change over a few thousand seconds. The initial bare surface and simulated fault gouge experiments were conducted in rotary shear at 25 MPa normal stress, 21 MPa confining stress and at displacements greater than 100 mm. In contrast, initially bare surface experiments at 5 MPa normal stress, unconfined at displacements less than 10 mm show effectively no change ind h . We attribute the difference to the presence of an appreciable shear zone that develops due to wear over significant displacements, confined at elevated normal stress. Prior published studies of sheared simulated fault gouge at short displacement show both acknowledged and unacknowledged increases ind h that may relate to our observations. Since natural faults have well‐developed shear zones, the observations have more direct relevance to earthquake nucleation than prior laboratory studies that use short displacement data and focus on frictional strength recovery alone. However, the physics underlying this increase in weakening distance are not known; candidates are compaction (Nakatani, 1998) and delocalization (Sleep et al., 2000). Additional caveats are that these are room temperature and humidity experiments, at a single normal stress that have not yet been reproduced in other laboratories. -
more » « less
Abstract Establishing a constitutive law for fault friction is a crucial objective of earthquake science. However, the complex frictional behavior of natural and synthetic gouges in laboratory experiments eludes explanations. Here, we present a constitutive framework that elucidates the rate, state, and temperature dependence of fault friction under the relevant sliding velocities and temperatures of the brittle lithosphere during seismic cycles. The competition between healing mechanisms, such as viscoelastic collapse, pressure‐solution creep, and crack sealing, explains the low‐temperature stability transition from steady‐state velocity‐strengthening to velocity‐weakening as a function of slip‐rate and temperature. In addition, capturing the transition from cataclastic flow to semi‐brittle creep accounts for the stabilization of fault slip at elevated temperatures. We calibrate the model using extensive laboratory data on synthetic albite and granite gouge, and on natural samples from the Alpine Fault and the Mugi Mélange in the Shimanto accretionary complex in Japan. The constitutive model consistently explains the evolving frictional response of fault gouge from room temperature to 600°C for sliding velocities ranging from nanometers to millimeters per second. The frictional response of faults can be uniquely determined by the in situ lithology and the prevailing hydrothermal conditions.
-
more » « less
Abstract We use densely spaced campaign GPS observations and laboratory friction experiments on fault rocks from one of the world's most rapidly slipping low‐angle normal faults, the Mai'iu fault in Papua New Guinea, to investigate the nature of interseismic deformation on active low‐angle normal faults. GPS velocities reveal 8.3 ± 1.2 mm/year of horizontal extension across the Mai'iu fault, and are fit well by dislocation models with shallow fault locking (above 2 km depth), or by deeper locking (from ~5–16 km depth) together with shallower creep. Laboratory friction experiments show that gouges from the shallowest portion of the fault zone are predominantly weak and velocity‐strengthening, while fault rocks deformed at greater depths are stronger and velocity‐weakening. Evaluating the geodetic and friction results together with geophysical and microstructural evidence for mixed‐mode seismic and aseismic slip at depth, we find that the Mai'iu fault is most likely strongly locked at depths of ~5–16 km and creeping updip and downdip of this region. Our results suggest that the Mai'iu fault and other active low‐angle normal faults can slip in large (Mw > 7) earthquakes despite near‐surface interseismic creep on frictionally stable clay‐rich gouges.
-
more » « less
Abstract Isotopic studies of Canadian Rocky Mountain thrust faults preserve the timing and identity of orogenic fluids and their fault zone pathways. Using previously dated samples, we measure the O‐ and H‐isotopic compositions of fault gouge. These nearly 100% neomineralized gouges and their associated damage zones act as primary orogenic fluid pathways. As such, they provide a specific and local look into the nature of the Late Jurassic to Early Eocene orogenic plumbing system in the Alberta Rockies. Considering clay polytype stability and regional temperature conditions, we obtain a range of geofluid isotopic compositions during Jurassic‐Eocene thrust faulting: δ18Ofluidranged from ∼−3.3 to 9.2 ± 3.2‰; δDfluidranged from −119 to −46 ± 13‰ VSMOW. The range of O‐ and H‐isotopic compositions reflects mixing of fluid sources, including the pervasive presence of surface‐sourced fluids (up to ∼90%). The interpreted prevalence of a surface fluid source in fault rocks is in agreement with regional isotopic trends previously observed in undated veins of fractured host rock. Our results confirm that thrust faults of the Alberta Rocky Mountains acted as major fluid‐focusing conduits during orogenic activity. We further show that these faults incorporated both deeply sourced and surface‐sourced fluids into zones of enhanced and dynamic permeability, heterogeneously distributing fluids along fault planes across the fold‐thrust belt, promoting the growth of fault‐zone weakening clay minerals.
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1038/s41467-022-27998-2
