skip to main content
US FlagAn official website of the United States government
dot gov icon
Official websites use .gov
A .gov website belongs to an official government organization in the United States.
https lock icon
Secure .gov websites use HTTPS
A lock ( lock ) or https:// means you've safely connected to the .gov website. Share sensitive information only on official, secure websites.

Explore Research Products in the PAR
It may take a few hours for recently added research products to appear in PAR search results.


Title: Sodium and potassium ion storage in cation substituted 2D MoWSe 2 : insights into the effects of upper voltage cut-off
Abstract The superior properties, such as large interlayer spacing and the ability to host large alkali-metal ions, of two-dimensional (2D) materials based on transition metal di-chalcogenides (TMDs) enable next-generation battery development beyond lithium-ion rechargeable batteries. In addition, compelling but rarely inspected TMD alloys provide additional opportunities to tailor bandgap and enhance thermodynamic stability. This study explores the sodium-ion (Na-ion) and potassium-ion (K-ion) storage behavior of cation-substituted molybdenum tungsten diselenide (MoWSe2), a TMD alloy. This research also investigates upper potential suspension to overcome obstacles commonly associated with TMD materials, such as capacity fading at high current rates, prolonged cycling conditions, and voltage polarization during conversion reaction. The voltage cut-off was restricted to 1.5 V, 2.0 V, and 2.5 V to realize the material’s Na+and K+ion storage behavior. Three-dimensional (3D) surface plots of differential capacity analysis up to prolonged cycles revealed the convenience of voltage suspension as a viable method for structural preservation. Moreover, the cells with higher potential cut-off values conveyed improved cycling stability, higher and stable coulombic efficiency for Na+and K+ion half-cells, and increased capacity retention for Na+ion half-cells, respectively, with half-cells cycled at higher voltage ranges.  more » « less
Award ID(s):
1743701
PAR ID:
10468937
Author(s) / Creator(s):
;
Publisher / Repository:
IOP publishing
Date Published:
Journal Name:
Nanotechnology
Volume:
34
Issue:
38
ISSN:
0957-4484
Page Range / eLocation ID:
385401
Format(s):
Medium: X
Sponsoring Org:
National Science Foundation
More Like this
  1. ; (, Nanomaterials)
    Transition metal dichalcogenides (TMDs) such as the WS2 have been widely studied as potential electrode materials for lithium-ion batteries (LIB) owing to TMDs’ layered morphology and reversible conversion reaction with the alkali metals between 0 to 2 V (v/s Li/Li+) potentials. However, works involving TMD materials as electrodes for sodium- (NIBs) and potassium-ion batteries (KIBs) are relatively few, mainly due to poor electrode performance arising from significant volume changes and pulverization by the larger size alkali-metal ions. Here, we show that Na+ and K+ cyclability in WS2 TMD is improved by introducing WS2 nanosheets in a chemically and mechanically robust matrix comprising precursor-derived ceramic (PDC) silicon oxycarbide (SiOC) material. The WS2/SiOC composite in fibermat morphology was achieved via electrospinning followed by thermolysis of a polymer solution consisting of a polysiloxane (precursor to SiOC) dispersed with exfoliated WS2 nanosheets. The composite electrode was successfully tested in Na-ion and K-ion half-cells as a working electrode, which rendered the first cycle charge capacity of 474.88 mAh g−1 and 218.91 mAh g−1, respectively. The synergistic effect of the composite electrode leads to higher capacity and improved coulombic efficiency compared to the neat WS2 and neat SiOC materials in these cells. 
    more » « less
  2. ; ; ; ; ; ; ; ; ; ; et al (, Carbon Energy)
    Abstract A new concentrated ternary salt ether‐based electrolyte enables stable cycling of lithium metal battery (LMB) cells with high‐mass‐loading (13.8 mg cm−2, 2.5 mAh cm−2) NMC622 (LiNi0.6Co0.2Mn0.2O2) cathodes and 50 μm Li anodes. Termed “CETHER‐3,” this electrolyte is based on LiTFSI, LiDFOB, and LiBF4with 5 vol% fluorinated ethylene carbonate in 1,2‐dimethoxyethane. Commercial carbonate and state‐of‐the‐art binary salt ether electrolytes were also tested as baselines. With CETHER‐3, the electrochemical performance of the full‐cell battery is among the most favorably reported in terms of high‐voltage cycling stability. For example, LiNixMnyCo1–x–yO2(NMC)‐Li metal cells retain 80% capacity at 430 cycles with a 4.4 V cut‐off and 83% capacity at 100 cycles with a 4.5 V cut‐off (charge at C/5, discharge at C/2). According to simulation by density functional theory and molecular dynamics, this favorable performance is an outcome of enhanced coordination between Li+and the solvent/salt molecules. Combining advanced microscopy (high‐resolution transmission electron microscopy, scanning electron microscopy) and surface science (X‐ray photoelectron spectroscopy, time‐of‐fight secondary ion mass spectroscopy, Fourier‐transform infrared spectroscopy, Raman spectroscopy), it is demonstrated that a thinner and more stable cathode electrolyte interphase (CEI) and solid electrolyte interphase (SEI) are formed. The CEI is rich in lithium sulfide (Li2SO3), while the SEI is rich in Li3N and LiF. During cycling, the CEI/SEI suppresses both the deleterious transformation of the cathode R‐3m layered near‐surface structure into disordered rock salt and the growth of lithium metal dendrites. 
    more » « less
  3. ; ; ; ; ; ; ; ; ; ; et al (, Journal of The Electrochemical Society)
    Sodium-ion batteries (SIBs) with Earth-abundant elements are promising for global electrification, but electrolyte stability impacts electrochemical performance and safety. This study compares non-fluorinated 1,2-diethoxyethane (DEE) and fluorinated 1,2-bis(2,2-difluoroethoxy)ethane (F4DEE) as electrolyte solvents in Na0.97Ca0.03[Mn0.39Fe0.31Ni0.22Zn0.08]O2(NCMFNZO)/hard carbon (HC) pouch cells up to 4.0 V. Fluorination slightly reduces ionic conductivity and increases viscosity but significantly enhances electrochemical stability and safety. Cells with F4DEE exhibit lower impedance, reduced gas evolution, and less voltage decay during high-voltage storage at 40 °C. Long-term cycling shows ∼85% capacity retention after 500 cycles at 25 °C and ∼80% at 40 °C with less transition metal dissolution, outperforming DEE-based cells. Isothermal microcalorimetry reveals lower parasitic heat generation with F4DEE, while soft X-ray absorption spectroscopy confirms stabilized Ni and Mn oxidation states, indicating suppressed electrolyte oxidation. Accelerating rate calorimetry reveals improved thermal stability with F4DEE. These findings highlight fluorinated ether solvents as a promising approach to enhance SIB lifespan and safety, with ongoing challenges requiring further solvent and additive optimization. 
    more » « less
  4. ; ; ; ; ; ; ; ; ; ; et al (, ChemSusChem)
    Abstract Despite large theoretical energy densities, metal‐sulfide electrodes for energy storage systems face several limitations that impact the practical realization. Here, we present the solution‐processable, room temperature (RT) synthesis, local structures, and application of a sulfur‐rich Mo3S13chalcogel as a conversion‐based electrode for lithium‐sulfide batteries (LiSBs). The structure of the amorphous Mo3S13chalcogel is derived throughoperandoRaman spectroscopy, synchrotron X‐ray pair distribution function (PDF), X‐ray absorption near edge structure (XANES), and extended X‐ray absorption fine structure (EXAFS) analysis, along with ab initio molecular dynamics (AIMD) simulations. A key feature of the three‐dimensional (3D) network is the connection of Mo3S13units through S−S bonds. Li/Mo3S13half‐cells deliver initial capacity of 1013 mAh g−1during the first discharge. After the activation cycles, the capacity stabilizes and maintains 312 mAh g−1at a C/3 rate after 140 cycles, demonstrating sustained performance over subsequent cycling. Such high‐capacity and stability are attributed to the high density of (poly)sulfide bonds and the stable Mo−S coordination in Mo3S13chalcogel. These findings showcase the potential of Mo3S13chalcogels as metal‐sulfide electrode materials for LiSBs. 
    more » « less
  5. ; ; (, ECS Meeting Abstracts)
    Layer-structured Na intercalation compounds such as NaxMO2 (M=Co, Mn, Cr) have attracted much attention as cathode materials for sodium-ion batteries due to their high volumetric and gravimetric energy densities. Among them, NaCrO2 with layered rock salt structure is one of the promising cathodes since NaCrO2 has a desirable flat and smooth charge/discharge voltage plateau.1 In addition, NaCrO2 has the highest thermal stability at charged state which makes it a potentially safer cathode material.2 The NaCrO2 exhibits a reversible capacity of 110 mAh g-1 with good cycling performance.3 However, the transition metal oxide (TMO) cathode materials in NIBs undergo severe chemo-mechanical deformations which leads to capacity fade and poor cycling and is the limiting factor of NIBs. The electrochemical characterization and examination of the electrode structure were the primary focus of several investigations. To improve the lifespan and performance of electrode materials for Na-ion batteries, it is vital to comprehend how Na ions impact the chemo-mechanical stability of the electrodes. In this talk, we will discuss the driving forces behind the structural and interfacial deformations on NaCrO2 cathodes. Digital image correlation measurements were conducted to probe strain evolution in the electrode during cycling. The free-standing composite NaCrO2 electrode was used for stain measurements in custom-cell assembly. The battery was cycled against Na metal in 1 M NaClO4 in PC. The first part of the study involves structural and interfacial deformations in the lower voltage range of 2.3 V to 3.5 V where x<0.5 in NaxCrO2. And the second part focuses on the structural and interfacial deformations in the voltage range of 2.3 V to 4.7 V where x>0.5 in NaxCrO2. In the preliminary studies, we observed that the initial insertion of Na ions leads to negative strain evolution (contraction) in the electrode, followed by expansions in the electrode at a higher state of discharge. Similar phenomena are also observed during charge cycles, where extraction of Na results in an initial contraction in the electrode, followed by expansion at a higher state of charge. Understanding the mechanisms behind chemo-mechanical deformations will allow to tune structure & material property for better electrochemical performance. 
    more » « less
  • Citation Formats
  • MLA
  • APA
  • Chicago
  • BibTeX
  • Text Encoded Conversion
  • XML
  • Save / Share this Record
  • Send to Email