An official website of the United States government
Abstract In NMR experiments, it is crucial to control the temperature of the sample, especially when measuring kinetic parameters. Usually, it takes 2 to 5 min for the temperature of the sample inside the NMR probe to stabilize at a fixed value set for the experiment. However, the NMR sample tubes are flame‐sealed in some cases, such as when working with volatile solvents, atmosphere‐sensitive samples, or calibration samples for long‐term use. When these samples are placed inside the NMR probe, the spectrometer controls the lower portion (liquid phase) of the NMR sample tube with a gas flow at a fixed temperature, while the upper portion (vapor) is at ambient temperature. This probe design creates a unique temperature gradient across the sample, leading to vapor pressure build‐up, particularly inside a sealed NMR tube. By analyzing the temperature‐dependent spectral line shape changes of a chemical exchange process, we report that under standard experimental conditions, the sample temperature can take up to 2 to 3 h (instead of minutes) to stabilize. The time scale of the liquid–vapor equilibrium process is much slower, with a half‐life exceeding 35 min, in contrast to the 2‐min duration required to obtain each spectrum. This phenomenon is exclusively due to the liquid–vapor equilibrium process of the flame‐sealed NMR tube and is not observable otherwise.
more »
« less
High-pressure vapor-liquid equilibrium measurements of methane + water mixtures by nuclear magnetic resonance spectroscopy
The vapor-liquid equilibrium (VLE) of methane + water mixtures has been studied with nuclear magnetic resonance (NMR) spectroscopy. This work had two primary goals. The first goal was to develop methods that broaden the utility of NMR spectroscopy for VLE measurements. In this regard, we report a method by which the liquid-phase and vapor-phase compositions are measured in separate experiments by adjusting the height of the liquid phase in the sample tube. We also report a method for hastening phase equilibration by adding glass beads to the sample and repeatedly inverting the sample tube. The second goal of this work was to collect VLE data on a challenging mixture with real-world importance. Mixtures of methane + water are a useful test case because of their challenging characteristics, including the widely differing vapor pressures of the two components. One use for accurate VLE data on methane + water mixtures is to better predict the formation of harmful liquid phases in natural gas pipelines. Herein we utilize 1H NMR spectroscopy to measure the VLE of methane + water mixtures at temperatures of 299.73, 307.98, and 323.25 K, and pressures ranging from 0.69 MPa to 13.89 MPa. Experiments were carried out with a 600 MHz spectrometer. Mixtures were prepared and equilibrated in a high pressure zirconia sample tube with an integrated needle valve. NMR-based VLE measurements on the liquid phase are in good agreement with available literature data and with Henry’s Law predictions at low pressures. However, the commonly used GERG-2008 model for natural gas systems deviates dramatically from the experimental data for the liquid phase. NMR-based VLE measurements on the vapor-phase resulted in measured water concentrations that are systematically lower than available literature data and models. This systematic offset is likely caused by peak overlap in the NMR spectra.
more »
« less
- Award ID(s):
- 1956323
- PAR ID:
- 10477708
- Publisher / Repository:
- Elsevier B. V.
- Date Published:
- Journal Name:
- Gas Science and Engineering
- Volume:
- 120
- ISSN:
- 2949-9089
- Page Range / eLocation ID:
- 205165
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Supercritical fluids, often present in modern high-performance propulsion systems, result from elevated operating pressures. When these systems utilize fluid mixtures as fuel or oxidizers, a transcritical effect often occurs. This effect can lead to misjudgments, as mixture critical points exceed those of individual components. Fluid mixing may induce phase separation, creating liquid and vapor phases due to the transcritical multi-component effect. Consequently, two-phase modeling is essential for transcritical and supercritical fluids. Traditional interface capturing methods, like Volume of Fluid (VOF) and Level Set (LS), present challenges such as computational expense and lack of conservatism. The Phase Field (PF) method, or the Diffuse Interface (DI) method which uses a phase fraction transport equation, emerges as a conservative alternative. Despite the absence of an initial interface in transcritical fluids, phase separation from mixing may form liquid droplets, necessitating multiphase modeling. To address these complexities, a Vapor-Liquid Equilibrium (VLE) model, coupled with the PR equation of state, is introduced. This model estimates phase fractions, liquid and vapor compositions, densities, and enthalpies through a flash problem solution. The conventional PF model is enhanced by replacing the phase fraction transport equation with VLE-derived values. The resulting VLE-based PF method is implemented into an OpenFOAM compressible solver, ensuring numerical stability with explicit phase field terms and a new CFL criterion. Test cases involve 1D interface convection and 2D droplet convection. In the 1D test, the VLE-based PF model adeptly captures interfaces, adjusting thickness as needed. The 2D droplet case, challenging due to a non-aligned Cartesian grid, exhibits uniform interface thickness and preserves droplet shape. The VLE-based PF model demonstrates versatility and reliability in capturing complex fluid behaviors, offering promising prospects for future research.more » « less
-
To achieve high power density and thermodynamic cycle efficiency, the working pressures of liquid-propellant rocket engines, diesel engines, and gas turbines (based on deflagration or detonation) are continuously increasing, which could reach or go beyond the thermodynamic critical pressure of the liquid propellant. For this reason, the studies of trans- and super-critical injection are getting more and more attention. However, the simulation of transcritical phase change is still a challenging topic. The phase boundary, especially near the mixture critical point, needs to be accurately determined to investigate the multicomponent effects on transcritical injection and atomization. This work used our previously developed thermodynamic model based on the vapor-liquid equilibrium (VLE) theory, which can predict the phase separation near the mixture critical point. An \textit{in situ} adaptive tabulation (ISAT) method was developed to accelerate the computationally expensive multicomponent VLE computation such that it can be cheap enough for CFD. The new thermodynamic model was integrated into OpenFOAM to develop a VLE-based CFD solver. In this work, shock-droplet interaction and two-phase mixing simulations are conducted using our new VLE-based CFD solver. The shock-droplet interaction simulation results capture the thermodynamic condition of the surface entering the supercritical state after shock passes through. The atomization of droplets could be triggered by vorticity formed at the droplets' surface. 2D temporal mixing layer simulations show the evolution of the transcritical mixing layer and capture the phase split effect at the mixing layer.more » « less
-
As molecular modeling and simulation techniques become increasingly important sources of thermophysical property and phase equilibrium data, the ability to assess the robustness of that data becomes more critical. Recently, the use of the compressibility factor (Z) has been suggested as a metric for testing the quality of simulation data for vapor−liquid equilibria (VLE). Here, we analyze predicted VLE data from the transferable potentials for phase equilibria (TraPPE) database and show that, apart from data entry or typographical errors, Z will always be well-behaved in Gibbs ensemble Monte Carlo (GEMC) simulations even when the simulations are not sufficiently equilibrated. However, this is not true for grand canonical Monte Carlo simulations. When the pressure is calculated from the internal forces, then pressure and density are strongly correlated for the vapor phase and, for GEMC simulations, it is recommended to treat Z as an instantaneous mechanical property. From analysis of the TraPPE VLE data, we propose a complementary metric based on the predicted vapor pressures at three neighboring temperatures and their deviation from a local Clausius−Clapeyron fit.more » « less
-
null (Ed.)Growing concerns about the global warming potential of hydrofluorocarbons (HFCs) has led to increasing interest in developing technologies to effectively recover and recycle these refrigerants. Ionic liquids (ILs) have shown great potential to selectively separate azeotropic HFC gas mixtures, such as R-410A composed of HFC-32 (CH2F2) and HFC-125 (CHF2CF3), based on solubility differences between the refrigerant gases in the respective IL. Isothermal vapor−liquid equilibrium (VLE) data for HFC-32 and HFC-125 were measured in ILs containing fluorinated and nonfluorinated anions using a gravimetric microbalance at pressures ranging from 0.05 to 1.0 MPa and a temperature of 298.15 K. The van der Waals equation of state (EoS) model was applied to correlate the experimental solubility data of each HFC refrigerant/IL mixture. The solubility differences between HFC-32 and HFC-125 vary significantly depending on the choice of IL. The diffusion coefficients for both HFC refrigerants in each IL were calculated by fitting Fick’s law to time-dependent absorption data. HFC-32 has a higher diffusivity in most ILs tested because of its smaller molecular radius relative to HFC-125. Based on the calculated Henry’s law constants and the mass uptake for each system, [C6C1im][Cl] was found to have the highest selectivity difference for separating R-410A at 298.15 K.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1016/j.jgsce.2023.205165
