An official website of the United States government
SUMMARY This paper deals with in situ characterization of the small-strain shear-wave velocity VS and damping ratio DS from an advanced interpretation of Multi-channel Analysis of Surface Waves (MASW) surveys. A new approach based on extracting Rayleigh wave data using the CFDBFa method has been discussed in the companion paper. This paper focuses on mapping the experimental Rayleigh wave phase velocity and attenuation into profiles of VS and DS versus depth, which is achieved through a joint inversion procedure. The joint inversion of phase velocity and attenuation data utilizes a newly developed Monte Carlo global search algorithm, which implements a smart sampling procedure. This scheme exploits the scaling properties of the solution of the Rayleigh eigenvalue problem to modify the trial earth models and improve the matching with the experimental data. Thus, a reliable result can be achieved with a limited number of trial ground models. The proposed algorithm is applied to the inversion of synthetic data and of experimental data collected at the Garner Valley Downhole Array site, as described in the companion paper. In general, inverted soil models exhibit well-defined VS profiles, whereas DS profiles are affected by larger uncertainties. Greater uncertainty in the inverted DS profiles is a direct result of higher variability in the experimental attenuation data, the limited wavelength range at which reliable values of attenuation parameters can be retrieved, and the sensitivity of attenuation data to both DS and VS. Nonetheless, the resulting inverted earth models agree well with alternative in situ estimates and geological data. The results stress the feasibility of retrieving both stiffness and attenuation parameters from active-source MASW testing and the effectiveness of extracting in situ damping ratio estimates from surface wave data.
more »
« less
Novel techniques for in situ estimation of shear-wave velocity and damping ratio through MASW testing – I: a beamforming procedure for extracting Rayleigh-wave phase velocity and phase attenuation
SUMMARY A robust, in situ estimate of shear-wave velocity VS and the small-strain damping ratio DS (or equivalently, the quality factor QS) is crucial for the design of buildings and geotechnical systems subjected to vibrations or earthquake ground shaking. A promising technique for simultaneously obtaining both VS and DS relies on the Multichannel Analysis of Surface Waves (MASW) method. MASW can be used to extract the Rayleigh wave phase velocity and phase attenuation data from active-source seismic traces recorded along linear arrays. Then, these data can be inverted to obtain VS and DS profiles. This paper introduces two novel methodologies for extracting the phase velocity and attenuation data. These new approaches are based on an extension of the beamforming technique which can be combined with a modal filter to isolate different Rayleigh propagation modes. Thus, the techniques return reliable phase velocity and attenuation estimates even in the presence of a multimode wavefield, which is typical of complex stratigraphic conditions. The reliability and effectiveness of the proposed approaches are assessed on a suite of synthetic wavefields and on experimental data collected at the Garner Valley Downhole Array and Mirandola sites. The results reveal that, under proper modelling of wavefield conditions, accurate estimates of Rayleigh wave phase velocity and attenuation can be extracted from active-source MASW wavefields over a broad frequency range. Eventually, the estimation of soil mechanical parameters also requires a robust inversion procedure to map the experimental Rayleigh wave parameters into soil models describing VS and DS with depth. The simultaneous inversion of phase velocity and attenuation data is discussed in detail in the companion paper.
more »
« less
- Award ID(s):
- 2037900
- PAR ID:
- 10492933
- Publisher / Repository:
- Oxford University Press
- Date Published:
- Journal Name:
- Geophysical Journal International
- Volume:
- 237
- Issue:
- 1
- ISSN:
- 0956-540X
- Format(s):
- Medium: X Size: p. 506-524
- Size(s):
- p. 506-524
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract Non-invasive surface wave methods are increasingly being used as the primary technique for estimating a site’s small-strain shear wave velocity (Vs). Yet, in comparison to invasive methods, non-invasive surface wave methods suffer from highly variable standards of practice, with each company/group/analyst estimating surface wave dispersion data, quantifying its uncertainty (or ignoring it in many cases), and performing inversions to obtain Vs profiles in their own unique manner. In response, this work presents a well-documented, production-tested, and easy-to-adopt workflow for developing estimates of experimental surface wave dispersion data with robust measures of uncertainty. This is a key step required for propagating dispersion uncertainty forward into the estimates of Vs derived from inversion. The paper focuses on the two most common applications of surface wave testing: the first, where only active-source testing has been performed, and the second, where both active-source and passive-wavefield testing has been performed. In both cases, clear guidance is provided on the steps to transform experimentally acquired waveforms into estimates of the site’s surface wave dispersion data and quantify its uncertainty. In particular, changes to surface wave data acquisition and processing are shown to affect the resulting experimental dispersion data, thereby highlighting their importance when quantifying uncertainty. In addition, this work is accompanied by an open-source Python package, swprocess , and associated Jupyter workflows to enable the reader to easily adopt the recommendations presented herein. It is hoped that these recommendations will lead to further discussions about developing standards of practice for surface wave data acquisition, processing, and inversion.more » « less
-
Abstract Near‐surface seismic velocity structure plays a critical role in ground motion amplification during large earthquakes. In particular, the local Vp/Vs ratio strongly influences the amplitude of Rayleigh waves. Previous studies have separately imaged 3D seismic velocity and Vp/Vs ratio at seismogenic depth, but lack regional coverage and/or fail to constrain the shallowest structure. Here, we combine three datasets with complementary sensitivity in a Bayesian joint inversion for shallow crustal shear velocity and near‐surface Vp/Vs ratio across Southern California. Receiver functions–including with an apparent delayed initial peak in sedimentary basins, and long considered a nuisance in receiver function imaging studies–highly correlate with short‐period Rayleigh wave ellipticity measurements and require the inclusion of a Vp/Vs parameter. The updated model includes near‐surface low shear velocity more in line with geotechnical layer estimates, and generally lower than expected Vp/Vs outside the basins suggesting widespread shallow fracturing and/or groundwater undersaturation.more » « less
-
Abstract The Formosa array, with 137 broadband seismometers and ∼5 km station spacing, was deployed recently in Northern Taiwan. Here by using eight months of continuous ambient noise records, we construct the first high‐resolution three‐dimensional (3‐D) shear wave velocity model of the crust in the area. We first calculate multi‐component cross‐correlations to extract robust Rayleigh wave signals. We then determine phase velocity maps between 3 and 10 s periods using Eikonal tomography and measure Rayleigh wave ellipticity at each station location between 2 and 13 s periods. For each location, we jointly invert the two types of Rayleigh wave measurements with a Bayesian‐based inversion method for a one‐dimensional shear wave velocity model. All piecewise continuous one‐dimensional models are then used to construct the final 3‐D model. Our 3‐D model reveals upper crustal structures that correlate well with surface geological features. Near the surface, the model delineates the low‐velocity Taipei and Ilan Basins from the adjacent fast‐velocity mountainous areas, with basin geometries consistent with the results of previous geophysical exploration and geological studies. At a greater depth, low velocity anomalies are observed associated with the Linkou Tableland, Tatun Volcano Group, and a possible dyke intrusion beneath the Southern Ilan Basin. The model also provides new geometrical constraints on the major active fault systems in the area, which are important to understand the basin formation, orogeny dynamics, and regional seismic hazard. The new 3‐D shear wave velocity model allows a comprehensive investigation of shallow geologic structures in the Northern Taiwan.more » « less
-
Abstract Shear attenuation provides insights into the physical and chemical state of the upper mantle. Yet, observations of attenuation are infrequent in the oceans, despite recent proliferation of arrays of ocean‐bottom seismometers (OBSs). Studies of attenuation in marine environments must overcome unique challenges associated with strong oceanographic noise at the seafloor and data loss during OBS recovery in addition to untangling the competing influences of elastic focusing, local site amplification, and anelastic attenuation on surface‐wave amplitudes. We apply Helmholtz tomography to OBS data to simultaneously resolve array‐averaged Rayleigh wave attenuation and maps of site amplification at periods of 20–150 s. The approach explicitly accounts for elastic focusing and defocusing due to lateral velocity heterogeneity using wavefield curvature. We validate the approach using realistic wavefield simulations at the NoMelt Experiment and Juan de Fuca (JdF) plate, which represent endmember open‐ocean and coastline‐adjacent environments, respectively. Focusing corrections are successfully recovered at both OBS arrays, including at periods <35 s at JdF where coastline effects result in strong multipathing. When applied to real data, our observations of Rayleigh wave attenuation at NoMelt and JdF revise previous estimates. At NoMelt, we observe a low attenuation lithospheric layer (> 1,500) overlying a highly attenuating asthenospheric layer (∼ 50 to 70). At JdF, we find a broad peak in attenuation (∼ 50 to 60) centered at a depth of 100–130 km. We also report strong local site amplification at the JdF Ridge (>10% at 31 s period), which can be used to refine models of crust and shallow mantle structure.more » « less
