A parametric study was carried out for the first firing cycle of a 4-cylinder, 2.0-liter, turbocharged gasoline direct injection (GDI) engine. The primary goal was to see how changes in the fuel injection parameters would affect the GDI engine combustion and emissions for the first four combustion events that constitute the first firing cycle. Experimental studies were carried out with a custom-designed powertrain control system to measure the HC emissions and pressure development for the first firing cycle. The quantitative experimental results were accompanied by simulations of the detailed temporal and spatial fuel concentration profiles using Converge CFD engine simulation software. An alternative calculation method was used to calculate the average combustion equivalence ratio for each of the four cylinders. This method showed that the majority of the cold start HC emissions during the first firing cycle was unburned gasoline and its possible decomposition products, which did not contribute significantly to the combustion and heat release. For the same amount of fuel injected into a cylinder, increased fuel rail pressure resulted in better evaporation and combustion, while slightly increasing the HC emissions during the cold start process. A multiple injection strategy was studied that split the fuel delivery between the intake stroke and the compression stroke with either one or two injections in each of those strokes (two or four injections total). The quadruple injection strategy led to better first cycle combustion, with higher engine IMEP and lower HC emissions. This resulted from a richer fuel mixture in the region near the spark plug due to better fuel evaporation and a better spatial fuel distribution. While increasing fuel rail pressure with either injection strategy failed to significantly lower the HC emissions given the same amount of injected fuel mass, higher rail pressure with the quadruple injection strategy resulted in higher IMEP for the same amount of injected fuel; this may provide the possibility to reduce the total fuel injection mass which may have benefits for both fuel consumption and emissions.
more »
« less
Development of a fractal engine simulation model in a multidimensional simulation for the cold start process of a gasoline direct injection engine
A fractal engine simulation (FES) sub-model was integrated into three-dimensional simulations for modeling turbulent combustion for a gasoline direct injection (GDI) engine. The FES model assumes that the effects of turbulence on flame propagation are to wrinkle and stretch the flame, and fractal geometry is used to predict the surface area increase and thus the turbulent burning velocity. Different formulas for the four sequential stages of combustion in SI engines are proposed to account for the changing effects of turbulence throughout the combustion process. However, most prior studies related to the FES model were quasi-dimensional simulations, with few found in multi-dimensional studies, and none under cold start conditions or stratified charges. This paper describes how the model was implemented into multidimensional simulations in CONVERGE CFD, and what the formulas are in the four sequential stages of combustion in SI engines. The capabilities of the FES model for simulating the cold start cases, under the conditions of the dramatically changing engine speed and mixture stratification in a complex engine geometry, are presented in this study. The FES model was able to not only simulate the steady-state cases with constant engine speed, but also predict the in-cylinder pressure traces in all four cylinders for the very first firing cycle with transient engine speed, and gave good agreement with the experimental measurements under these extremely transient conditions. The uncertain maximum fractal dimension was chosen as 2.37 in this research, and a simple linear correlation with engine speed was used to obtain the coefficient used in calculating the kernel formation time which controls the so-called combustion or ignition delay.
more » « less- NSF-PAR ID:
- 10494395
- Publisher / Repository:
- Sage Publications
- Date Published:
- Journal Name:
- International Journal of Engine Research
- Volume:
- 24
- Issue:
- 9
- ISSN:
- 1468-0874
- Page Range / eLocation ID:
- 3830 to 3849
- Subject(s) / Keyword(s):
- Fractal engine simulation (FES) model gasoline direct injection (GDI) engine cold start three-dimensional simulation turbulent combustion
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
The unstretched laminar flame speed (LFS) plays a key role in engine models and predictions of flame propagation. It is also an essential parameter in the study of turbulent combustion and can be directly used in many turbulent combustion models. Therefore, it is important to predict the laminar flame speed accurately and efficiently. Two improved correlations for the unstretched laminar flame speed, namely improved power law and improved Arrhenius form correlations, are proposed for iso-octane/air mixtures in this study, using simulated results for typical operating conditions for spark-ignition engines: unburned temperatures of 300-950 K, pressures of 1-120 bar, and equivalence ratios of 0.6-1.5. The original data points used to develop the new correlations were obtained using the detailed combustion kinetics for iso-octane from Lawrence Livermore National Laboratory (LLNL). The three coefficients in the improved power law correlation were determined using a methodology different from previous approaches. The improved Arrhenius form correlation employs a function of unburned gas temperature to replace the flame temperature, making the expression briefer and making the coefficients easier to calculate. The improved Arrhenius method is able to predict the trends and the values of laminar flame speed with improved accuracy over a larger range of operating conditions. The improved power law method also works well but for a relatively narrow range of predictions. The improved Arrhenius method is recommended, considering its overall fitting error was only half of that using the improved power law correlation and it was closer to the experimental measurements. Even though ϕm, the equivalence ratio at which the laminar flame speed reaches its maximum, is not monotonic with pressure, this dependence is still included, since it produces least-rich best torque (LBT). The comparisons between the improved correlations in this study and the experimental measurements and the other correlations from various researchers are shown as well.more » « less
-
more » « less
Abstract Diesel-fueled engines still hold a large market share in the medium and heavy-duty transportation sector. However, the increase in fossil fuel prices and the strict emission regulations are leading engine manufacturers to seek cleaner alternatives without a compromise in performance. Alcohol-based fuels, such as ethanol, offer a promising alternative to diesel fuel in meeting regulatory demands. Ethanol provides cleaner combustion and lower levels of soot due to its chemical properties, in particular its lower level of carbon content. In addition, the stoichiometric operating conditions of alcohol fueled engines enable the mitigation of NOx emissions in aftertreatment stage. With the promise of retrofitting diesel engines to run on ethanol to reduce emissions, the thermal efficiency of these engines remains the primary optimization target. In order to find the optimal ethanol-fueled engine design that maximizes the thermal efficiency, a large design space needs to be investigated using engineering tools.
In this study, previous research by the authors on optimizing the design of a single-cylinder ethanol-fueled engine was extended to explore the design space for a heavy-duty multi-cylinder engine configuration. A heavy-duty engine setup with multiple operating conditions at different engine speeds and loads were considered. A design optimization analysis was performed to identify the potential designs that maximize the indicated thermal efficiency in an ethanol-fueled compression ignition engine. First, a computational fluid dynamics (CFD) model of the engine was validated using experimental data for four drive cycle points. Using a design of experiments (DoE) approach and a parameterized piston bowl geometry, the model was then exercised to explore the relationship among geometric features of the piston bowl and spray targeting angle and indicated thermal efficiency across all tested operating conditions. After evaluating 165 candidate designs, a piston bowl geometry was identified that yielded an increase between 1.3 to 2.2 percentage points in indicated thermal efficiency for all tested conditions, while satisfying the operational design constraints for peak pressure and maximum pressure rise rate. The increased performance was attributed to enhanced mixing that led to the formation of a more homogeneous distribution of in-cylinder temperature and equivalence ratio, higher combustion temperatures, and shorter combustion duration. Finally, a Bayesian optimization (BOpt) analysis was employed to find the optimal piston bowl geometry with a fixed spray injector angle for one of the operating conditions. Using BOpt, a piston candidate was identified that resulted in a 1.9 percentage point increase in thermal efficiency from the baseline design, yet only required 65% of the design samples investigated using the DoE approach.
-
This work describes and tests the calibration process of the chemical-diffusive model (CDM) for the simulation of non-premixed diffusion flames. The CDM is an alternative, simplified approach for incorporating the effects of combustion in a fluid simulation, based on the ideas of regulating the rate of energy release such that the properties of combustion waves (e.g. flames and detonations) are reproduced. Past implementations of the CDM have considered single-stoichiometry fuel-air mixtures or mixtures with variable stoichiom- etry but with premixed modes of combustion. In this work, the CDM is tested and shown to work for non-premixed, low-Mach-number flames (i.e., diffusion flames) by incorporat- ing it into a numerical model which solves the reactive and compressible Navier-Stokes equations with the barely implicit correction (BIC) algorithm, which removes the acoustic limit on the integration time-step size. Simulations of one-dimensional premixed laminar flames reproduce the required premixed laminar flame speed, thickness, and temperature. A two-dimensional, steady-state, laminar coflow diffusion flame is computed, and the result demonstrates the ability of the algorithm to compute a non-premixed flame. Lastly, a two- dimensional simulation of two opposing jets of fuel and air show that the CDM approach can compute the structure of a counter-flow diffusion flame.more » « less
-
more » « lessSince its implementation, exhaust gas recirculation has proven to be a reliable technique to control NOx emissions by lowering combustion temperature. Dilution with exhaust gas recirculation, whether in internal combustion engines or sequential-staged gas turbine combustors, affects flame reactivity and stability, which are related to the heat release rate and engine power. Another way to control emissions is to use hydrogen as a carbon-free alternative fuel, which is considered a milestone in the energy-decarbonization journey. However, the high reactivity of hydrogen is one of its hurdles and understanding this effect on laminar burning velocity is important. Flame propagation and burning velocity control the mixture reactivity and exothermicity and are related to abnormal combustion phenomena, such as flashback and knock. Therefore, understanding the effect of exhaust gas addition on the laminar burning velocity of hydrogen/air mixtures is imperative for engine design. In this work, a constant volume combustion chamber was used to observe the laminar burning velocity of stoichiometric hydrogen/air mixtures diluted with combustion products at 1 bar and 423K. Actual combustion products (35 % H2O + 65 % N2, by mole) were used for dilution at rates of 0-50%. The burned gas Markstein length was calculated for all mixtures. Experimental results of the laminar burning velocities for all mixtures were compared with kinetic modeling results. These measurements showed the monotonic reduction of reactivity and the laminar burning velocity with dilution. The reduced burning rates at higher dilution were reflected on the pressure gradient inside the vessel. Markstein length values decreased with dilution, meaning that flame instabilities increased with dilution.
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1177/14680874231174272
