An official website of the United States government
Abstract We reveal and justify, both theoretically and experimentally, the existence of a unifying criterion of the boiling crisis. This criterion emerges from an instability in the near-wall interactions of bubbles, which can be described as a percolation process driven by three fundamental boiling parameters: nucleation site density, average bubble footprint radius and product of average bubble growth time and detachment frequency. Our analysis suggests that the boiling crisis occurs on a well-defined critical surface in the multidimensional space of these parameters. Our experiments confirm the existence of this unifying criterion for a wide variety of boiling surface geometries and textures, two boiling regimes (pool and flow boiling) and two fluids (water and liquid nitrogen). This criterion constitutes a simple mechanistic rule to predict the boiling crisis, also providing a guiding principle for designing boiling surfaces that would maximize the nucleate boiling performance.
more »
« less
Subcooled Pool Boiling on Hierarchical Micro- and Nanostructure-Modified Copper Surfaces in HFE-7100 Dielectric Liquid
Hierarchical surfaces comprised of both microscale and nanoscale structures have been previously studied as a means of targeting multiple length scales to achieve superior pool boiling performance. However, preceding studies have focused almost exclusively on high surface tension working fluids while technologically important low surface tension fluids have remained largely unexplored. In this work, we utilize scalable manufacturing techniques to realize four separate surface types (planar, nanoscale-modified, microscale-modified, and hierarchical) and experimentally determine their respective pool boiling performance within the low surface tension commercial working fluid HFE-7100. A maximum heat transfer enhancement of 125 % at 38 K of superheat was observed for the best performing samples, which interestingly were nanoscale-modified and not those of the hierarchical type. Visual observations via high-speed video analysis of vapor bubble behaviour are utilized to explain the underlying multiphase physics as to why these samples performed so well and future directions for achieving surface optimization across multiple length scales.
more »
« less
- Award ID(s):
- 1846165
- PAR ID:
- 10500565
- Publisher / Repository:
- Taylor & Francis
- Date Published:
- Journal Name:
- Nanoscale and Microscale Thermophysical Engineering
- Volume:
- 28
- Issue:
- 1
- ISSN:
- 1556-7265
- Page Range / eLocation ID:
- 59 to 68
- Subject(s) / Keyword(s):
- Pool boiling, micro-fins, nanostructures, bubble dynamics, phase change
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract When studying bone fragility diseases, it is difficult to identify which factors reduce bone’s resistance to fracture because these diseases alter bone at many length scales. Here, we investigate the contribution of nanoscale collagen behavior on macroscale toughness and microscale toughening mechanisms using a bovine heat-treatment fragility model. This model is assessed by developing an in situ toughness testing technique for synchrotron radiation micro-computed tomography to study the evolution of microscale crack growth in 3D. Low-dose imaging is employed with deep learning to denoise images while maintaining bone’s innate mechanical properties. We show that collagen damage significantly reduces macroscale toughness and post-yield properties. We also find that bone samples with a compromised collagen network have reduced amounts of crack deflection, the main microscale mechanism of fracture resistance. This research demonstrates that collagen damage at the nanoscale adversely affects bone’s toughening mechanisms at the microscale and reduces the overall toughness of bone.more » « less
-
Electronic components, especially the CPUs/GPUs used in data centers are concentrated heat-generating sources. Their large Thermal Design Power (TDP), small die area and confined packaging make their thermal management a unique challenge. While conventional single-phase cooling methods fail to dissipate such large amounts of heat efficiently, recently developed two-phase cooling systems also lack the holistic approach of combining efficient boiling and condensation mechanisms. It is hypothesized that subcooled boiling with submerged condensation and reduced saturation pressure will result in high-heat flux dissipation while maintaining low surface temperatures. The novel boiling chamber presented in this work is demonstrated in a compact configuration that fits in a 1U/2U server rack by combining submerged condensation with subcooled pool boiling. The boiling chamber is filled with 13% and 40% fill ratio of water and Novec-7000 and experimentally investigated on a thermal test vehicle. Results show that the boiling chamber dissipates about 400 W of heat with a surface temperature of less than 80 °C using Novec-7000 working fluid. When tested with water, the device dissipated more than 750 W of heat (heat flux ≈ 67 W/cm2) with a surface temperature of less than 90 °C. Though the surface temperature rose to 120°C, further testing shows the device to dissipate more than 1 kW from a 34.5 × 32 mm2 plain copper chip. High-speed images identify submerged condensation and small diameters of vapor bubbles. Further enhancements can be achieved by implementing enhanced boiling and condensation surfaces. Lastly, a guide to design considerations and future work is provided to unlock the greater performance potential of the novel boiling chamber.more » « less
-
Abstract Power intensification and miniaturization of electronics and energy systems are causing a critical challenge for thermal management. Single-phase heat transfer mechanisms including natural and forced convection of air and liquids cannot meet the ever-increasing demands. Two-phase heat transfer modes, such as evaporation, pool boiling, flow boiling, have much higher cooling capacities but are limited by a variety of practical instabilities, e.g., the critical heat flux (CHF), aka departure from nucleate boiling (DNB) in the nuclear industry, flow maldistribution, flow reversal, among others. These instabilities are often triggered suddenly during normal operation, and if not identified and mitigated in time, will lead to overheating issues and detrimental device failures. For example, when CHF is triggered during pool boiling, the device temperature can ramp up in the order of 150 °C/min. It is thus critical to implement real-time detection and mitigation algorithms for two-phase cooling. In the present work, we have developed an accurate and reliable technology for fault detection of high-performance two-phase cooling systems by coupling acoustic emission (AE) with multimodal fusion using deep learning. We have leveraged the contact AE sensor attached to the heater and hydrophones immersed in the working fluid to enable non-invasive fault detection.more » « less
-
Abstract Electrohydrodynamic jet (e‐jet) printing is a high‐resolution additive manufacturing technique that holds promise for the fabrication of customized micro‐devices. In this companion paper set, e‐jet printing is investigated for its capability in depositing multilayer thin‐films with microscale spatial resolution and nanoscale thickness resolution to create arrays of 1D photonic crystals (1DPC). In this paper, an empirical model for the deposition process is developed, relating process and material parameters to the thickness and uniformity of the patterns. Standard macroscale measurements of solid surface energy and liquid surface tension are used in conjunction with microscale contact angle measurements to understand the length scale dependence of material properties and their impact on droplet merger into uniform microscale thin‐films. The model is validated with several photopolymer inks, a subset of which is used to create pixelated, multilayer arrays of 1DPCs with uniformity and resolution approaching standards in the optics manufacturing industry. It is found that the printed film topography at the microscale can be predicted based on the surface energetics at the microscale. Due to the flexibility in design provided by the e‐jet process, these findings can be generalized for fabricating additional multimaterial, multilayer micro‐ and nanostructures with applications beyond the field of optics.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1080/15567265.2023.2293710
