An official website of the United States government
Recent developments in sensing technologies have triggered a lot of research interest in exploring novel self-powered, inexpensive, compact and flexible pressure sensors with the potential for structural health monitoring (SHM) applications. Herein, we assessed the performance of an embedded mechanoluminescent (ML) and perovskite pressure sensor that integrates the physical principles of mechanoluminescence and perovskite materials. For a continuous in-situ SHM, it is crucial to evaluate the capabilities of the sensing device when embedded into a composite structure. An experimental study of how the sensor is affected by the embedment process into a glass fiber-reinforced composite has been conducted. A series of devices with and without ML were embedded within a composite laminate, and the signal responses were collected under different conditions. We also demonstrated a successful encapsulation process in order for the device to withstand the composite manufacturing conditions. The results show that the sensor exhibits distinct signals when subjected to different load conditions and can be used for the in-situ SHM of advanced composite structures.
more »
« less
An efficient way of harvesting mechanoluminescent light: Flexible pressure sensor application
Mechanoluminescent (ML) materials are used for fabricating sensors and other devices such as artificial skin, colorful displays, and energy harvesting devices. However, a key challenge in developing ML-based sensors is the ability to effectively capture and efficiently transmit ML light from the sensing location. Here we report a flexible and sensitive thin film pressure sensor, created using a novel combination of ML material and perovskite. In this work, we adopted a simple lateral type design of a thin pressure sensor primarily consisting of (i) a sensing layer of copper-doped zinc sulfide (ZnS:Cu)/polydimethylsiloxane (PDMS) composite and (ii) a light absorbing layer of perovskite. The mixed halide perovskite, a light absorbing material, fully absorbs the green light emitted from ZnS:Cu. The sensor demonstrated consistent signal output under the mechanical bending test. A thin encapsulation layer of PMMA on the perovskite layer prevents moisture inclusion. This innovative technique of utilizing integrated thin perovskite to efficiently harvest ML light has the potential to open up new avenues for advanced research in ML-perovskite-based sensor systems.
more »
« less
- Award ID(s):
- 1950500
- PAR ID:
- 10502510
- Publisher / Repository:
- ScienceDirect
- Date Published:
- Journal Name:
- Journal of Luminescence
- Volume:
- 260
- Issue:
- C
- ISSN:
- 0022-2313
- Page Range / eLocation ID:
- 119895
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract Flexible and wearable sensors show enormous potential for personalized healthcare devices by real‐time monitoring of an individual's health. Typically, a single functional material is selected for one sensor to sense a particular physical signal while multiple materials will be selected for multi‐mode sensing. Vertically aligned nanocomposites (VANs) have recently demonstrated various material combinations and novel coupled multifunctionalities that are hard to achieve in any single‐phase material alone, including multiphase multiferroics, magneto‐optic coupling, and strong magnetic and optical anisotropy. Integrating these novel VANs into wearable sensors shows enormous potential in multi‐mode sensing owing to their multifunctional nature. In this work, the transfer of VANs onto polydimethylsiloxane as a novel flexible chemical and pressure sensor is demonstrated. For this demonstration, the classical BaTiO3‐Au VAN with combined plasmonic and piezoelectric properties is used to demonstrate a multi‐sensing mechanism. A thin water‐soluble buffer of Sr3Al2O6serves as a buffer layer for the epitaxial growth and transfer process. The electrical output based on the piezoelectric responses and identifying 4‐mercaptobenzoic acid by surface‐enhanced Raman spectroscopy reveal great potential for free‐standing VANs in a wearable multifunctional sensing platform.more » « less
-
Force sensors play an important role in the biomedical devices industry, especially in motion- and pressure-related devices. Such sensors are designed to collect force or pressure data by converting it into electrical signals. The data can then be sent to and analyzed by a local or cloud-based processing unit. It is vital that the sensors can be fabricated in a way that time efficiency, cost efficiency, and quality are all maximized. The advent of three-dimensional (3D) printing has greatly facilitated prototyping and customized manufacturing, as compared to older crafting methods (such as welding and woodworking), 3D printing requires less skill and involves less costly materials making it much more time- and cost-efficient. Technological advancements have also improved the quality of the actual sensing materials used in sensor-based devices, and notably, carbon-based materials have become increasingly favored for use as sensing elements. In the presented sensor, the modern sensor fabrication methods of 3D printing and using carbon materials as sensing elements are combined. The sensor presented as a proof of the above concepts is a cantilever flex sensor. The sensor consists of a 30 mm-long cantilever extending from a 2.5 mm-thick wall, with a second wall of the same thickness parallel to the cantilever. After designing this structure and printing it using a 3D printer, the top surface of the cantilever was coated with a thin layer of conductive carbon paste and two copper wires were stripped and soldered to a pair of copper alligator clips, to be used for testing purposes. To test the sensor, the two copper wires were clipped onto the sensor (Figure 1A) and each wire was connected to a multimeter probe on the end opposite of the alligator clip. Then, using a set of four through holes in the parallel wall (along with a slotted rod), the tip of the cantilever was pressed down to an angle of 5, 10, 15, or 20 degrees (Figures 1B, 1C, 1D, and 1E, respectively) below the original plane of the cantilever and held there for 2 minutes. The resistance between the ends of the cantilever was measured throughout each trial by the multimeter, and the results (Figure 1F) for each angle were compiled and analyzed to determine the effect of each depression angle on impedance change, and thus, the overall effectiveness of the sensor. In the future, a notable improvement would be miniaturizing the sensor to facilitate in integration of the sensor in wearable and biomedical devices.more » « less
-
Sensitive and flexible pressure sensors have invoked considerable interest for a broad range of applications in tactile sensing, physiological sensing, and flexible electronics. The barrier between high sensitivity and low fabrication cost needs to be addressed to commercialize such flexible pressure sensors. A low-cost sacrificial template-assisted method for the capacitive sensor has been reported herein, utilizing a porous Polydimethylsiloxane (PDMS) polymer and a multiwalled carbon nanotube (MWCNT) composite-based dielectric layer. The sensor shows high sensitivity of 2.42 kPa−1 along with a low limit of detection of 1.46 Pa. The high sensitivity originates from adding MWCNT to PDMS, increasing the composite polymer’s dielectric constant. Besides this, the pressure sensor shows excellent stability at a cyclic loading of 9000 cycles, proving its reliability for long-lasting application in tactile and physiological sensing. The high sensitivity of the sensor is suitable for the detection of small deformations such as pulse waveforms as well as tactile pressure sensing. In addition, the paper demonstrates a simultaneous contact and non-contact sensing capability suitable for dual sensing (pressure and proximity) with a single data readout system. The dual-mode sensing capability may open opportunities for realizing compact systems in robotics, gesture control, contactless applications, and many more. The practicality of the sensor was shown in applications such as tactile sensing, Morse code generator, proximity sensing, and pulse wave sensing.more » « less
-
Abstract 2D black phosphorene (BP) carries a stellar set of physical properties such as conveniently tunable bandgap and extremely high ambipolar carrier mobility for optoelectronic devices. Herein, the judicious design and positioning of BP with tailored thickness as dual‐functional nanomaterials to concurrently enhance carrier extraction at both electron transport layer/perovskite and perovskite/hole transport layer interfaces for high‐efficiency and stable perovskite solar cells is reported. The synergy of favorable band energy alignment and concerted cascade interfacial carrier extraction, rendered by concurrent positioning of BP, delivered a progressively enhanced power conversion efficiency of 19.83% from 16.95% (BP‐free). Investigation into interfacial engineering further reveals enhanced light absorption and reduced trap density for improved photovoltaic performance with BP incorporation. This work demonstrates the appealing characteristic of rational implementation of BP as dual‐functional transport material for a diversity of optoelectronic devices, including photodetectors, sensors, light‐emitting diodes, etc.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1016/j.jlumin.2023.119895
