An official website of the United States government
Abstract The creation of fractures in bedrock dictates water movement through the critical zone, controlling weathering, vadose zone water storage, and groundwater recharge. However, quantifying connections between fracturing, water flow, and chemical weathering remains challenging because of limited access to the deep critical zone. Here we overcome this challenge by coupling measurements from borehole drilling, groundwater monitoring, and seismic refraction surveys in the central California Coast Range. Our results show that the subsurface is highly fractured, which may be driven by the regional geologic and tectonic setting. The pervasively fractured rock facilitates infiltration of meteoric water down to a water table that aligns with oxidation in exhumed rock cores and is coincident with the adjacent intermittent first‐order stream channel. This work highlights the need to incorporate deep water flow and weathering due to pervasive fracturing into models of catchment water balances and critical zone weathering, especially in tectonically active landscapes.
more »
« less
Progressive fracturing in alluvial clasts
Rock fracturing sets the pace for a range of geomorphic processes. While experimental studies and modeling have provided invaluable insights into the mechanisms and rates of rock fracturing as a function of stress, time, and environmental conditions, field-based observations of subaerial fracturing evolution over geologic time are scarce. To address this knowledge gap, we conducted a systematic study of fractures that developed subaerially and in situ within clasts perched on abandoned late Quaternary alluvial surfaces (ca. 0, ca. 14, and ca. 62 ka in age) in the hyperarid Dead Sea Rift Valley, Israel. Using quantitative field observations, petrographic, and scanning electron microscopy, and micron-scale laser scans of fracture surfaces we found that fractures exhibit a consistent pattern of three distinctive weathering zones: (1) an “Outer Zone,” where fracture surface morphology resembles the clast exterior; (2) an “Accumulation Zone,” where fractures are infilled by “loose” accumulated particles; and (3) an “Inner Zone” where fractures extend inward to the crack-tip and preferentially follow grain boundaries. Crack-tips are characterized as a distinct micro domain that consists of fracture-parallel microcracks, chemical alteration, and dissolution morphologies. Altogether, the laboratory results indicate chemically enhanced fracturing and infiltration of water ahead of traction-free, open crack-tips. Field measurements also revealed an increase in fracture number density over geologic time. Our results highlight new details regarding the progressive nature of mechanical weathering through geologic time and the role of moisture as a potential rate-setting factor in the fracturing that allows mechanical weathering.
more »
« less
- Award ID(s):
- 1839148
- PAR ID:
- 10507730
- Publisher / Repository:
- GSA
- Date Published:
- Journal Name:
- Geological Society of America Bulletin
- ISSN:
- 0016-7606
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Davidson, Cam; Wirth, Karl (Ed.)Fault-tip damage zones develop in response to fault propagation and displacement and are caused by the local amplification of stresses at the fault tip. Understanding the geometry and intensity of damage zones is crucial for evaluating earthquake hazards and assessing the potentials of oil and gas production, geothermal energy, and groundwater resources. Fractures initiate as a result of stresses exceeding rock strength and propagate based on the stress field at the fault tip. We investigate the damage zone of a fault segment within the Sevier normal fault zone near Orderville, Utah, focusing on fractures that developed within the Jurassic Navajo Sandstone, the Temple Cap Formation, and the oldest beds of the Carmel Formation. Because normal faults grow laterally as slip and displacement increase, we focus on the tip zone of a fault segment where fracturing is well-exposed. We executed a series of unmanned aerial vehicle (UAV) flights to capture high-resolution imagery of inaccessible rock exposures. We use these images to construct structure-from-motion (SfM) virtual outcrop models (VOMs) that we georeference and analyze using Agisoft Metashape. We collected and analyzed fracture orientation and intensity data in the field and with VOMs. Both types of data reveal a distribution of fracture intensity that is consistent with inner and outer damage zones similar to previous studies of other fault systems. Adjacent to the tip, the inner damage zone has a higher fracture intensity on the hanging wall compared to the footwall. This high fracture intensity on the hanging wall ends 30 meters over from the fault core where the intensity of the outer damage zone of the hanging wall becomes similar to that within the inner damage zone of the footwall. Laterally, along strike of the fault tip, intense fracturing ends 60 meters to the south and all fracturing ends 350 meters from the fault tip. Our results have implications for the spatial distribution of fracturing and related permeability in similar normal fault systems.more » « less
-
Abstract. Progressive fracturing contributes to structural degradation of natural rock arches and other freestanding rock landforms. However, methods to detect structural changes arising from fracturing are limited, particularly at sites with difficult access and high cultural value, where non-invasive approaches are essential. This study aims to determine how fractures affect the dynamic properties of rock arches, focusing on resonance modes as indicators of structural health conditions. We hypothesize that damage resulting from fracture propagation may influence specific resonance modes that can be identified through ambient vibration modal analysis. We characterized the dynamic properties (i.e., resonance frequencies, damping ratios, and mode shapes) of Hunter Canyon Arch, Utah (USA), using spectral and cross-correlation analyses of data generated from an array of nodal geophones. Results revealed properties of nine resonance modes with frequencies between 1 and 12 Hz. Experimental data were then compared to numerical models with homogeneous and heterogeneous compositions, the latter implementing weak mechanical zones in areas of mapped fractures. All numerical solutions replicated the first two resonance modes of the arch, indicating these modes are insensitive to structural complexity derived from fractures. Meanwhile, heterogenous models with discrete fracture zones succeeded in matching the frequency and shape of one additional higher mode, indicating this mode is sensitive to the presence of fractures and thus most likely to respond to structural change from fracture propagation. An evolutionary crack damage model was then applied to simulate fracture propagation, confirming that only this higher mode is sensitive to structural damage resulting from fracture growth. While examination of fundamental modes is common practice in structural health monitoring studies, our results suggest that analysis of higher-order resonance modes can be more informative for characterizing fracture-driven structural damage.more » « less
-
ABSTRACT:Due to rock mass being commonly subjected to compressive or shear loading, the mode II fracture toughness is an important material parameter for rocks. Fracturing in rocks is governed by the behavior of a nonlinear region surrounding the crack tip called the fracture process zone (FPZ). However, the characteristics of mode II fracture are still determined based on the linear elastic fracture mechanics (LEFM), which assumes that a pure mode II loading results in a pure mode II fracture. In this study, the FPZ development in Barre granite specimens under mode II loading was investigated using the short beam compression (SBC) test. Additionally, the influence of lateral confinement on various characteristics of mode II fracture was studied. The experimental setup included the simultaneous monitoring of surface deformation using the two-dimensional digital image correlation technique (2D-DIC) to identify fracture mode and characterize the FPZ evolution in Barre granite specimens. The 2D-DIC analysis showed a dominant mixed-mode I/II fracture in the ligament between two notches, irrespective of confinement level on the SBC specimens. The influence of confinement on the SBC specimens was assessed by analyzing the evolution of crack displacement and changes in value of mode II fracture toughness. Larger levels of damage in confined specimens were observed prior to the failure than the unconfined specimens, indicating an increase in the fracture resistance and therefore mode II fracture toughness with the confining stress. 1. INTRODUCTIONThe fracturing in laboratory-scale rock specimens is often characterized by the deformation of the inelastic region surrounding the crack tips, also known as the fracture process zone (FPZ) (Backers et al., 2005; Ghamgosar and Erarslan, 2016). While the influence of the FPZ on mode I fracture in rocks has been extensively investigated, there are limited studies on FPZ development in rocks under pure mode II loading (Ji et al., 2016; Lin et al., 2020; Garg et al., 2021; Li et al., 2021).more » « less
-
ABSTRACT:Creation of a fracture network in a hydraulic fracturing process is essential for subsurface energy extraction and CO2 sequestration. It is facilitated by reactivation of pre-existing intersecting weak layers and cemented cracks in the rock. In this study, a poromechanical model is developed for the hydraulic fracturing process in rocks containing such pre-existing weak layers. Based on the mixture theory, the crack band model is used to simulate the growth of a crack system. The governing equations with the parameters for hydromechanical coupling are derived, to describe the evolution of the opening and branching of cracks caused by water injection. Microplane model M7 is adopted to characterize the deformation and fracturing of the solid skeleton of the rock, and the Poiseuille law is used to characterize fluid flow through the hydraulic fractures. Numerical simulations are performed to reproduce and interpret recently published laboratory-scale hydraulic fracturing experiments conducted at Los Alamos National Laboratory (LANL). In these experiments, the rock was represented by confined plaster slabs containing orthogonal intersecting weak layers of higher porosity. Numerical simulations reveal how poromechanical characteristics such as the Biot coefficient and the fluid injection rate lead to various typical fracture modes observed in the experiments. These modes include formation of one dominant planar crack or various orthogonal fracture networks.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1130/B36670.1
