An official website of the United States government
Deformation experiments on hematite characterize its slip‐rate dependent frictional properties and deformation mechanisms. These data inform interpretations of slip behavior from exhumed hematite‐coated faults and present‐day deformation at depth. We used a rotary‐shear apparatus to conduct single‐velocity and velocity‐step experiments on polycrystalline specular hematite rock (∼17 μm average plate thickness) at slip rates of 0.85 μm/s to 320 mm/s, displacements of primarily 1–3 cm and up to 45 cm, and normal stresses of 5 and 8.5 MPa. The average coefficient of friction is 0.70; velocity‐step experiments indicate velocity‐strengthening to velocity‐neutral behavior at rates <1 mm/s. Scanning electron microscopy showed experimentally generated faults develop in a semi‐continuous, thin layer of red hematite gouge. Angular gouge particles have an average diameter of ∼0.7 μm, and grain size reduction during slip yields a factor of 10–100 increase in surface area. Hematite is amenable to (U‐Th)/He thermochronometry, which can quantify fault‐related thermal and mechanical processes. Comparison of hematite (U‐Th)/He dates from the undeformed material and experimentally produced gouge indicates He loss occurs during comminution at slow deformation rates without an associated temperature rise required for diffusive loss. Our results imply that, in natural fault rocks, deformation localizes within coarse‐grained hematite by stable sliding, and that hematite (U‐Th)/He dates acquired from ultracataclasite or highly comminuted gouge reflect minor He loss unrelated to thermal processes. Consequently, the magnitude of temperature rise and associated thermal resetting in hematite‐bearing fault rocks based on (U‐Th)/He thermochronometry may be overestimated if only diffusive loss of He is considered.
more »
« less
Deformation and Frictional Failure of Granular Media in 3D Analog and Numerical Experiments
Abstract Frictional sliding along grain boundaries in brittle shear zones can result in the fragmentation of individual grains, which ultimately can impact slip dynamics. During deformation at small scales, stick–slip motion can occur between grains when existing force chains break due to grain rearrangement or failure, resulting in frictional sliding of granular material. The rearrangement of the grains leads to dilation of the granular package, reducing the shear stress and subsequently leading to slip. Here, we conduct physical experiments employing HydroOrbs, an elasto-plastic material, to investigate grain comminution in granular media under simple shear conditions. Our findings demonstrate that the degree of grain comminution is dependent on both the normal force and the size of the grains. Using the experimental setup, we benchmark Discrete Element Method (DEM) numerical models, which are capable of simulating the movement, rotation, and fracturing of elasto-plastic grains subjected to simple shear. The DEM models successfully replicate both grain comminution patterns and horizontal force fluctuations observed in our physical experiments. They show that increasing normal forces correlate with higher horizontal forces and more fractured grains. The ability of our DEM models to accurately reproduce experimental results opens up new avenues for investigating various parameter spaces that may not be accessible through traditional laboratory experiments, for example, in assessing how internal friction or cohesion affect deformation in granular systems.
more »
« less
- Award ID(s):
- 1843676
- PAR ID:
- 10509330
- Publisher / Repository:
- SpringerLink
- Date Published:
- Journal Name:
- Pure and Applied Geophysics
- ISSN:
- 0033-4553
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Typical granular materials are far from optimal in terms of mechanical performance: Random packing leads to poor load transfer in the form of thin and dispersed force lines within the material, to inhomogeneous jamming, and to strain localization. In addition, localized contacts between individual grains result in low stiffness, strength and brittleness. Here we propose a granular material that simultaneously embodies three approaches to increase strength: geometrical design of individual grains, crystallization, and infiltration by an adhesive. Using mechanical vibrations, we assembled millimeter-scale 3D printed grains with rhombic dodecahedral shapes into fully dense FCC granular crystals. We then infiltrated the granular structure with a tacky, polyacrylic adhesive that is orders of magnitude weaker than the grains, but which provides sustained adhesion over large interfacial displacements. The resulting material is a fully dense, free-standing space filling granular crystal. Compressive tests show that these granular crystals are up to 60 times stronger than randomly packed cohesive spheres and they display a rich set of mechanisms: Nonlinear deformations, crystal plasticity reminiscent of atomistic mechanisms, cross-slip, shear-induced dilatancy, micro-buckling, and tensile strength. To capture some of these mechanisms we developed a multiscale model that incorporates local cohesion between grains, resolved shear and normal stresses on available slip planes, and prediction of compressive strength as function of loading orientation. The predicted strength is highly anisotropic and agrees well with the compression experiments. Once fully understood and harnessed, we envision that these mechanisms will lead to granular engineering materials with unusual combinations of mechanical performances attractive for many applications.more » « less
-
We report on an open-source, publicly available C++ software module called Chrono::GPU, which uses the Discrete Element Method (DEM) to simulate large granular systems on Graphics Processing Unit (GPU) cards. The solver supports the integration of granular material with geometries defined by triangle meshes, as well as co-simulation with the multi-physics simulation engine Chrono. Chrono::GPU adopts a smooth contact formulation and implements various common contact force models, such as the Hertzian model for normal force and the Mindlin friction force model, which takes into account the history of tangential displacement, rolling frictional torques, and cohesion. We report on the code structure and highlight its use of mixed data types for reducing the memory footprint and increasing simulation speed. We discuss several validation tests (wave propagation, rotating drum, direct shear test, crater test) that compare the simulation results against experimental data or results reported in the literature. In another benchmark test, we demonstrate linear scaling with a problem size up to the GPU memory capacity; specifically, for systems with 130 million DEM elements. The simulation infrastructure is demonstrated in conjunction with simulations of the NASA Curiosity rover, which is currently active on Mars.more » « less
-
Modelling seasonal landslide motion: Does it only depend on fluctuations in normal effective stress?Abstract Landslide motion is often simulated with interface‐like laws able to capture changes in frictional strength caused by the growth of the pore water pressure and the consequent reduction of the effective stress normal to the plane of sliding. Here it is argued that, although often neglected, the evolution of all the 3D stress components within the basal shear zone of landslides also contributes to changes in frictional strength and must be accounted for to predict changes in seasonal velocity. For this purpose, an augmented sliding‐consolidation model is proposed which allows for the computation of excess pore pressure development and downslope sliding with any constitutive law with 3D stress evolution. Simulations of idealised infinite slope models subjected to hydrologic forcing are used to study the role of in‐situ stress conditions and stress rate multiaxiality. Specifically, a Drucker‐Prager perfectly plastic model is used to replicate frictional failure and shear deformation at the base of landslides. The model reveals that conditions amenable to the shearing of a frictional interface are met only after numerous rainfall cycles, that is, when multiaxial stress rates are suppressed. In this case, the landslide is predicted to move through a seasonal ratcheting controlled only by the effective stress component normal to the plane of sliding. By contrast, in newly formed landslides, the multiaxial stress evolution is found to produce further regimes of motion, from plastic shakedown to cyclic failure, neither of which can be captured by interface‐like frictional laws. Notably, the model suggests that a transition across these regimes can emerge in response to an aggravation of the magnitude of forcing, implying that (i) fluctuations in climate may alter the seasonal trends of motion observed today; (ii) our ability to quantify landslide‐induced risks is impaired unless proper geomechanical models are used to examine their long‐term dynamics.more » « less
-
In automated layup manufacturing processes of fiber-reinforced polymer composites, the quality of the manufactured part is strongly dependent on frictional behavior. Improper control of frictional forces can lead to defect formation. Frictional sliding rheometry tests provide an innovative methodology to accurately characterize the tool-ply friction of unidirectional (UD) prepreg employing unique annular plate geometries. The effect of processing parameters (temperature, velocity, and normal force) on the frictional response of a carbon fiber prepreg was studied. Moreover, utilizing custom designed plate geometries coupled with optically transparent fixtures allowed for in-situ quantification of the prepreg-rigid surface contact area along with simultaneous characterization of the process parameter-dependent frictional mechanisms. Our findings highlight the reduction in frictional forces with increasing temperature, attributed to the increased resin flowability, while increases in sliding rates resulted in a pronounced increase in the frictional forces. The effect of applied load on the frictional characteristics was more complicated due to contributions from both the adhesive and normal forces. Finally, the results were interpreted in light of the contact area measurements performed at different temperatures, normal force, and sliding rate.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript
- Journal Article:
- https://doi.org/10.1007/s00024-024-03464-6
