An official website of the United States government
Frontal polymerization (FP) is a promising alternative manufacturing method for thermoset-based fiber-reinforced polymer composites (FRP) in comparison with the traditional autoclave/oven-curing method, due to its rapid curing process, low energy consumption, and low cost. Optimizing the weight contents of initiators relative to the resin’s mass is needed to adjust the mechanical properties of FRPs in industrial applications. This study investigates the effect of varying the photo-initiator (PI) weight content on tensile properties and the frontal polymerization characteristics, including the front velocity, front temperature, and degree of cure, in the FP process of the epoxy resin. Specifically, a dual-initiator system, including PI and thermal-initiator (TI), is used to initiate the polymerization process by ultraviolent (UV) light. The weight content of the TI is fixed at 1 w%, and the relative PI concentration is varied from 0.2 w% to 0.5 wt%. Results show that increasing the PI amount from 0.2 wt% to 0.3 wt% significantly improves the front velocity and the degree of cure by about two times. Increasing the PI content from 0.3 wt% to 0.4 wt% results in 15% and 26% higher degree of cure and front velocity, respectively. Moreover, due to the different front velocity in the top and bottom regions of the specimen, the specimens with 0.4 wt% PI exhibited a curved shape. The specimen with 0.5 wt% PI is thermally degraded and foamed. By comparing tensile properties, it is found that increasing the PI concentration from 0.2 wt% to 0.3 wt% improves the tensile strength and Young’s modulus by 3.91% and 7%, respectively, while the tensile strength and the Young’s modulus of frontal polymerized specimens are on average 8% and 14% higher than traditionally oven-cured ones, respectively.
more »
« less
Mechanical Characterization of Epoxy Resin Manufactured Using Frontal Polymerization
for thermoset-based fiber-reinforced polymer composites (FRP) in comparison with the traditional autoclave/oven-curing method, due to its rapid curing process, low energy consumption, and low cost. Optimizing the weight contents of initiators relative to the resin’s mass is needed to adjust the mechanical properties of FRPs in industrial applications. This study investigates the effect of varying the photoinitiator (PI) weight content on tensile properties and the frontal polymerization characteristics, including the front velocity, front temperature, and degree of cure, in the FP process of the epoxy resin. Specifically, a dual-initiator system, including PI and thermal-initiator (TI), is used to initiate the polymerization process by ultraviolent (UV) light. The weight content of the TI is fixed at 1 w%, and the relative PI concentration is varied from 0.2 w% to 0.5 wt%. Results show that increasing the PI amount from 0.2 wt% to 0.3 wt% significantly improves the front velocity and the degree of cure by about two times. Increasing the PI content from 0.3 wt% to 0.4 wt% results in 15% and 26% higher degree of cure and front velocity, respectively. Moreover, due to the different front velocity in the top and bottom regions of the specimen, the specimens with 0.4 wt% PI exhibited a curved shape. The specimen with 0.5 wt% PI is thermally degraded and foamed. By comparing tensile properties, it is found that increasing the PI concentration from 0.2 wt% to 0.3 wt% improves the tensile strength and Young’s modulus by 3.91% and 7%, respectively, while the tensile strength and the Young’s modulus of frontal polymerized specimens are on average 8% and 14% higher than traditionally ovencured ones, respectively.
more »
« less
- Award ID(s):
- 2208130
- PAR ID:
- 10540138
- Publisher / Repository:
- Destech Publications, Inc.
- Date Published:
- ISBN:
- 9781605956916
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract Formulations containing vinyl ethers and epoxy were successfully polymerized through a radical‐induced cationic frontal polymerization mechanism, using an iodonium salt superacid generator with a peroxide thermal radical initiator and fumed silica as a filler. It was found that an increase of vinyl ether content resulted in higher front velocities for divinyl ethers in formulations with trimethylolpropane triglycidyl ether. However, increased hydroxymonovinyl ether either decreased the front velocity or suppressed frontal polymerization. The kinetic effects of the superacid generator and thermal radical initiator with varying vinyl ether content were also studied. It was observed that increasing concentrations of initiators increased the front velocity, with the system exhibiting higher sensitivity to the superacid generator concentration.more » « less
-
Abstract Frontal polymerization (FP) of epoxy monomers is typically achieved with a radical‐induced cationic frontal polymerization (RICFP) process that combines a thermal radical initiator with an onium salt superacid generator. In this paper, we show that both thermal and UV‐initiated cationic frontal polymerizations are possible for common epoxy and vinyl ether monomers with only an iodonium superacid generator in the absence of a standalone thermal radical initiator. Increasing superacid generator concentration resulted in an increase in front velocity, as did the addition of vinyl ether to epoxies. The front velocity is reduced by the addition of 4‐methoxyphenol (MeHQ), indicating free‐radicals play a significant role.more » « less
-
Ozden, O. (Ed.)Adhesively bonded composite joints can help reduce weight in structures and avoid material damage from fastener holes, but stress concentrations formed at the edges of the adhesive bond line are a main cause of failure. Stress concentrations within the adhesive can be reduced by lowering the stiffness at these edges and increasing the stiffness in the center of the joint. This may be achieved using a dual-cure adhesive system, where conventional curing is first used to bond a lap joint, after which high energy radiation is applied to the joint to induce additional crosslinking in specific regions. Anhydride-cured epoxy resins have been formulated to include a radiation sensitizer enabling the desired cure behavior. Tensile testing was performed on cured systems containing varying levels of radiation sensitizer in order to evaluate its effects on young’s modulus as a function of radiation dose.more » « less
-
Abstract This note presents approximate analytical expressions for the velocity of the self‐propagating reaction front in the frontal polymerization of thermoset polymers and composites. Prior estimates available in the literature for the front velocity have been limited by their applicability to simple reaction kinetics. The improved estimates provided in this work are shown to be applicable to complex reaction kinetics encountered in the frontal polymerization of neat thermoset polymers or fiber‐reinforced polymer‐matrix composites with a wide range of polymer chemistries, including dicyclopentadiene, cyclooctadiene, acrylates, and epoxies. They are also shown to be applicable to wide range of values of the initial temperature and initial degree of cure of the resin, and of the volume fraction of the reinforcing phase.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Conference Paper:
- https://doi.org/10.12783/asc38/36607
