An official website of the United States government
Mechano- or tribochemical processes are often induced by the large pressures, of the order of 1 GPa, exerted at contacting asperities at the solid–solid interface. These tribochemical process are not very well understood because of the difficulties of probing surface-chemical reaction pathways occurring at buried interfaces. Here, strategies for following surface reaction pathways in detail are illustrated for the tribochemical decomposition of 7-octenoic and octanoic acid adsorbed on copper. The chemistry was measured in ultrahigh vacuum by sliding either a tungsten carbide ball or a silicon atomic force microscope (AFM) tip over the surface to test a previous proposal that the nature of the terminal group in the carboxylic acid, vinyl versus alkyl, could influence its binding to the counterface, and therefore the reaction rate. The carboxylic acids bind strongly to the copper substrate as carboxylates to expose the hydrocarbon terminus. The tribochemical reaction rate was found to be independent of the nature of the hydrocarbon terminus, although the pull-off and friction forces measured by the AFM were different. The tribochemical reaction is initiated in the same way as the thermal reaction, by the carboxylate group tilting to eliminate carbon dioxide and deposit alkyl species onto the surface. This reaction occurs thermally at ∼640 K, but tribochemically at room temperature, producing significant differences in the rates and selectivities of the subsequent decomposition pathways of the adsorbed products.
more »
« less
Elucidating tribochemical reaction mechanisms: insights into tribofilm formation from hydrocarbon adsorbates coupled with tribochemical substrate wear
The molecules with higher tribochemical reactivity exhibited smaller activation volume, implying that less mechanical energy was required to initiate tribochemical reactions.
more »
« less
- PAR ID:
- 10553505
- Publisher / Repository:
- RSC
- Date Published:
- Journal Name:
- RSC Mechanochemistry
- Volume:
- 1
- Issue:
- 4
- ISSN:
- 2976-8683
- Page Range / eLocation ID:
- 328 to 341
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
This paper shows how the effect of combined normal and shear stresses on the rates of tribochemical reactions can be calculated using Evans-Polanyi (E-P) perturbation theory. The E-P approach is based on transition-state theory, where the rate of reaction is taken to be proportional to the concentration of activated complex. The equilibrium constant depends on the molar Gibbs free energy change between the initial- and transition-states, which, in turn, depends on the stresses. E-P theory has been used previously to successfully calculate the effects of normal stresses on reaction rates. In this case, ln(Rate) varies linearly with stress with a slope given by an activation volume, which broadly corresponds to the volume difference between the reactant and activated complex. An advantage of E-P theory is that it can calculate the influence of several perturbations, for example, the normal stress dependence of the shear stress during sliding. In this paper, E-P theory is used to calculate shear-induced, tribochemical reaction rates. The results depend on four elementary activation volumes for different contributions to the Gibbs free energy: two of them due to normal and shear stresses for sliding over the surface and two more for the surface reaction. The results of the calculations show that there is a linear dependence of ln(Rate) on the normal stress but that the coefficient of proportionality between the ln(Rate) and the normal stress now has contributions from all elementary-step activation volumes. Counterintuitively, the analysis predicts that the ln(Rate)-normal stress evolution tends, at zero normal stress, to an asymptotic rate constant that depends on sliding velocity and differs from the thermal reaction rate. The theoretical prediction is verified for the shear-induced decomposition of ethyl thiolate species adsorbed on a Cu(100) single crystal substrate that decomposes by C‒S bond cleavage. The theoretical analyses show that tribochemical reactions can be influenced by either just normal stresses or by a combination of normal and shear stresses, but that the latter effect is much greater. Finally, it is predicted that there should be a linear relationship between the activation energy and the logarithm of the pre-exponential factor of the asymptotic rate constant.more » « less
-
Tribochemistry, which is another name for mechanochemistry driven by shear, deals with complex and dynamic interfacial processes that can lead to surface wear or formation of beneficial tribofilms. For better mechanistic understanding of these processes, we investigated the reactivity of tribopolymerization of organic molecules with different internal ring strain (methylcyclopentane, cyclohexane, and cyclohexene) on a stainless steel (SS) surface in inert (N2), oxidizing (O2), and reducing (H2) environments at room temperature. On the clean stainless steel surface, precursor molecules were found to physisorb with a broad range of molecular orientations. In inert and reducing environments, the strain-free cyclohexane showed the lowest tribochemical activity among the three molecules tested. Compared to the N2 environment, the tribochemical activity in H2 was suppressed. In the O2 environment, only cyclohexene produced tribofilms and methylcyclopentane while cyclohexane did not. When tribofilms were analyzed with Raman spectroscopy, the spectral features of diamond-like carbon (DLC) or amorphous carbon (a-C) were observed due to photochemical degradation of triboproducts. Based on infrared spectroscopy, tribofilms were found to be organic polymers containing oxygenated groups. Whenever polymeric tribrofilms were produced, wear volume was suppressed by orders of magnitudes but not completely to zero. These results support previously suggested mechanisms which involve surface oxygen as a reactant species in the tribopolymerization process.more » « less
-
Abstract High-contact stresses generated at the sliding interfaces during their relative movement provide a unique combination of local heating and shear- and load-induced compression conditions. These conditions, when involving the sliding of surfaces with certain material characteristics, may facilitate tribochemical reactions with the environment, leading to the formation of a protective, damage-suppressing tribofilm directly at the contact. Here, we employ the electrodeposition process to design a coating composed of a hard cobalt-phosphorous matrix with the inclusion of tribocatalytically-active nickel clusters. The coating is optimized in terms of its relative composition and mechanical characteristics. We demonstrate the excellent tribological performance of the coating in the presence of a hydrocarbon environment, both in the form of a liquid lubricant and as a hydrocarbon-saturated vapor. Characterization of the wear track indicates that the origin of such performance lies in the formation of a protective carbon-based tribofilm on the surface of the coating during sliding. These results contribute to the advancement of knowledge on material transformations in the contact, thus providing a robust and versatile approach to addressing tribological challenges in mechanical systems.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1039/d3mr00036b
