An official website of the United States government
Small nanoparticles of ceria deposited on a powder of CuO display a very high selectivity for the production of methanol via CO2 hydrogenation. CeO2/CuO catalysts with ceria loadings of 5%, 20%, and 50% were investigated. Among these, the system with 5% CeOx showed the best catalytic performance at temperatures between 200 and 350 °C. The evolution of this system under reaction conditions was studied using a combination of environmental transmission electron microscopy (E-TEM), in situ X-ray absorption spectroscopy (XAS), and time-resolved X-ray diffraction (TR-XRD). For 5% CeOx/Cu, the in situ studies pointed to a full conversion of CuO into metallic copper, with a complete transformation of Ce4+ into Ce3+. Images from E-TEM showed drastic changes in the morphology of the catalyst when it was exposed to H2, CO2, and CO2/H2 mixtures. Under a CO2/H2 feed, there was a redispersion of the ceria particles that was detected by E-TEM and in situ TR-XRD. These morphological changes were made possible by the inverse oxide/metal configuration and facilitate the binding and selective conversion of CO2 to methanol.
more »
« less
Observing Chemical and Morphological Changes in a Cu@TiO x Core@Shell Catalyst: Impact of Reversible Metal-Oxide Interactions on CO 2 Activation and Hydrogenation
A combination of several in situ techniques (XRD, XAS, AP-XPS, and E-TEM) was used to explore links between the structural and chemical properties of a Cu@TiOx catalyst under CO2 hydrogenation conditions. The active phase of the catalyst involved an inverse oxide/metal configuration, but the initial core@shell motif was disrupted during the pretreatment in H2. As a consequence of strong metal–support interactions, the titania shell cracked, and Cu particles migrated from the core to on top of the oxide with the simultaneous formation of a Cu–Ti–Ox phase. The generated Cu particles had a diameter of 20–40 nm and were decorated by small clusters of TiOx (<5 nm in size). Results of in situ XAS and XRD and images of E-TEM showed a very dynamic system, where the inverse oxide/metal configuration promoted the reactivity of the system toward CO2 and H2. At room temperature, CO2 oxidized the Cu nanoparticles (CO2,gas → COgas + Ooxide) inducing a redistribution of the TiOx clusters and big modifications in catalyst surface morphology. The generated oxide overlayer disappeared at elevated temperatures (>180 °C) upon exposure to H2, producing a transient surface that was very active for the reverse water–gas shift reaction (CO2 + H2 → CO + H2O) but was not stable at 200–350 °C. When oxidation and reduction occurred at the same time, under a mixture of CO2 and H2, the surface structure evolved toward a dynamic equilibrium that strongly depended on the temperature. Neither CO2 nor H2 can be considered as passive reactants. In the Cu@TiOx system, morphological changes were linked to variations in the composition of metal-oxide interfaces which were reversible with temperature or chemical environment and affected the catalytic activity of the system. The present study illustrates the dynamic nature of phenomena associated with the trapping and conversion of CO2.
more »
« less
- Award ID(s):
- 1905422
- PAR ID:
- 10554148
- Publisher / Repository:
- American Chemical Society
- Date Published:
- Journal Name:
- ACS Catalysis
- Volume:
- 14
- Issue:
- 15
- ISSN:
- 2155-5435
- Page Range / eLocation ID:
- 11832 to 11844
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
null (Ed.)A series of Al2O3-supported Fe-containing catalysts were synthesized by incipient wetness impregnation. The iron surface density was varied from 1 to 13 Fe atoms/nm2 spanning sub- and above-monolayer coverage. The resulting supported Fe-catalysts were characterized with N2 physisorption, ex situ XRD, PDF, XAS, AC-STEM and chemically probed by H2-TPR. The results suggest that over this entire range of loadings, Fe was present as dispersed species, with only a very small fraction of Fe2O3 aggregates, at the highest Fe loading. The in situ sulfidation of Fe/Al2O3 resulted in the formation of a highly active and selective PDH catalyst. The highest activity with 52% propane conversion and ~99% propylene selectivity at 560 °C was obtained for the 6.4 Fe/Al2O3 catalyst suggesting that this is the highest amount of Fe that could be fully dispersed on the support in sulfided form. XRD and AC-STEM indicated the absence of any crystalline iron sulfide aggregates after sulfidation and reaction. H2-TPR results indicated that the amount of the reducible Fe sites in the sulfided catalyst remained constant above monolayer coverage, and increasing loading did not increase the number of reducible Fe sites. Consistent with these results, the reactivity per gram of catalyst showed no increase with Fe loading above monolayer coverage, suggesting that additional Fe remains conformal to the alumina surface.more » « less
-
A simple procedure was developed to synthesize molybdenum carbide nanoparticles (Mo2C/BC) by carburization of molybdate salts supported on the biochar from pyrolysis of biomass without using extra carbon source or reducing gas. The molybdenum carbide formation procedure investigated by in-situ XRD and TGA-MS indicated that the phase transitions followed the path of (NH4)6Mo7O24·4H2O → (NH4)2Mo3O10 → (NH4)2Mo14O42 → Mo8O23 → Mo4O11 → MoO2 → Mo2C. The volatile gases CO, H2, and CH4 evolved from biochar and the biochar solid carbon participated in the reduction of molybdenum species, while the biochar and CH4 served as carbon sources for the carburization. Temperature programmed surface reactions of Mo2C/BC indicated that CH4 dissociated as CH4 ⇋ C∗ + 2H2 on the catalyst surface, and CO2 reacted as CO2 + C∗ ⇋ 2CO+ ∗ due to oxidation of Mo2C. Both experiment data and thermodynamic analysis for the study of operation conditions of CO2 reforming of CH4 clearly demonstrated that the yields of H2 and CO increased with the increased temperature and the reasonable conversions should be performed at 850 °C, at which both CH4 and CO2 conversions were higher than 80%.more » « less
-
Ni/SBA-15 meso-structured catalysts modified with chromium and CeO2 (Ni–Cr-CeO2/SBA-15) were utilized to produce hydrogen from glycerol steam reforming (GSR). The catalysts were synthesized by a one-pot hydrothermal process and extensively characterized by analytical techniques such as N2 adsorption–desorption (BET), H2-temperature programmed reduction (H2-TPR), powder X-ray diffraction (PXRD), inductively coupled plasma-optical emission spectrometry (ICP-OES), and transmission electron microscopy (TEM). The low-angle XRD reflections affirmed that the catalysts were crystalline and possessed a 2D-ordered porosity. The BET results depicted that all the catalysts exhibited a good surface area ranging from 633 to 792m2/g, and the pore sizes were consistently in the mesoporous range (between 3 and 5 nm). TEM analysis of both calcined and spent catalysts revealed that the metal active sites were embedded in the hybrid CeO2-SiO2 support. Overall, the Ni-based catalysts exhibited higher glycerol conversion -12Ni-SBA-15–99.9%, 12Ni3CeO2-SBA-15–89.4%, and 8Ni4Cr3CeO2-SBA-15–99.7%. Monometallic 12Ni/SBA-15 performed exceptionally well, while 12Cr/SBA-15 performed poorly with the highest 71.48% CO selectivity. For short-term GSR reactions, CeO2 addition to 12Ni/SBA-15 did not have any effect, whereas Cr addition resulted in a 32% decrease in H2 selectivity. The long-term stability studies of 12Ni-SBA-15 showed H2 selectivity of ~ 64% and ~ 98% glycerol conversion. However, its activity was short-lived. After 20–30 h, the H2 selectivity and conversion dropped precipitously to 40%. The doping of mesoporous Ni/SBA-15 with Cr and CeO2 remarkably enhanced the long-term stability of the catalyst for 12Ni3CeO2-SBA-15, and 8Ni4Cr3CeO2-SBA-15 catalyst which showed ~ 58% H2 selectivity and ~ 100% conversion for the entire 60 h. Interestingly, Cr and CeO2 seem to improve the shelf-life of Ni-SBA-15 via different mechanistic pathways. CeO2 mitigated Ni poisoning through coke oxidation whereas Cr bolstered the catalyst stability via maintaining a well-defined pore size, structural rigidity, and integrity of the heterogeneous framework, thereby restricting structural collapse, and hence retard sintering of the Ni active sites during the long-term 60 h of continuous reaction. Hydrogen generation from renewable biomass like glycerol could potentially serve as a sustainable energy source and could substantially help reduce the carbon footprint of the environmentmore » « less
-
CO2 electroreduction (CO2ER) by using renewable energy resources is a promising method to mitigate the CO2 level in the atmosphere as well as producing valuable chemicals. Local environment at the electrode-electrolyte interface plays a key role in CO2ER activity and selectivity along with its competing hydrogen evolution reaction (HER). In addition to the catalyst and reactor design, electrolyte has also a significant impact on the interface. Herein, electrolyte additives were used to modify the local environment around the Cu catalyst during CO2ER. To this purpose, 10mM of ionic additives with bis(trifluoromethylsulfonyl)imide ([NTF2]-) and dicyanamide ([DCA]-) as anions and 1-butyl-3-methylimidazolium ([BMIM]+), potassium (K+), or sodium (Na+) as cations have been added to an aqueous potassium bicarbonate solution (0.1 M KHCO3). COMSOL Multiphysics was also used to calculate the local pH and CO2 concentration at electrode-electrolyte interface in different electrolytes. Results showed that the local environment modifications by the electrolyte additives altered the activity and selectivity of Cu in CO2ER. It was found that the CO2ER activity at -0.92 V was enhanced when using anion with high CO2 affinity and high hydrophobicity such as [NTF2]–. Among [NTF2]–-based additives, [BMIM][NTF2] had a higher faradaic efficiency (FE) for formate (38.7%) compared to K[NTF2] (23.2%) and Na[NTF2] (18.5%) at -0.92 V likely due to the presence of imidazolium cation which can further stabilize the intermediates on the surface and enhance CO2ER. Electrolytes containing [DCA]–-based additives with high hydrophilicity and low CO2 affinity had a very high HER selectivity (>90% FEH2) and low CO2ER selectivity regardless of the cation nature. This observation is attributed to the presence of hydrophilic [BMIM][DCA] in the vicinity of the catalyst which impacts the microenvironment around the catalyst. We observed that [DCA]– anions have a high affinity to adsorb on Cu catalysts as soon as the catalyst is submerged in the electrolyte. Although FTIR showed that [DCA]– anions desorb from the surface at negative potentials, it is likely that [DCA]– anions still remain in the proximity of the electrode, next to the adsorbed cations, impacting the transport of H2O and CO2, and altering the product selectivity. COMSOL calculations showed that the local pH is directly proportional to the H2 evolution activity. Also, hydrophilic salts such as those with the [DCA]– anion had a more alkaline local pH which leads to a lower CO2 concentration in the vicinity of the catalyst.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1021/acscatal.4c02694
