An official website of the United States government
Abstract Geological storage of carbon dioxide (CO2) in depleted gas reservoirs represents a cost-effective solution to mitigate global carbon emissions. The surface chemistry of the reservoir rock, pressure, temperature, and moisture content are critical factors that determine the CO2 adsorption capacity and storage mechanisms. Shale-gas reservoirs are good candidates for this application. However, the interactions of CO2 and organic content still need further investigation. The objectives of this paper are to (i) experimentally investigate the effect of pressure and temperature on the CO2 adsorption capacity of activated carbon, (ii) quantify the nanoscale interfacial interactions between CO2 and the activated carbon surface using Monte Carlo molecular modeling, and (iii) quantify the correlation between the adsorption isotherms of activated carbon-CO2 system and the actual carbon dioxide adsorption on shale-gas rock at different temperatures and geochemical conditions. Activated carbon is used as a proxy for kerogen. The objectives aim at obtaining a better understanding of the behavior of CO2 injection and storage into shale-gas formations. We performed experimental measurements and Grand Canonical Monte Carlo (GCMC) simulations of CO2 adsorption onto activated carbon. The experimental work involved measurements of the high-pressure adsorption capacity of activated carbon using pure CO2 gas. Subsequently, we performed a series of GCMC simulations to calculate CO2 adsorption capacity on activated carbon to validate the experimental results. The simulated activated carbon structure consists of graphite sheets with a distance between the sheets equal to the average actual pore size of the activated carbon sample. Adsorption isotherms were calculated and modeled for each temperature value at various pressures. The adsorption of CO2 on activated carbon is favorable from the energy and kinetic point of view. This is due to the presence of a wide micro to meso pore sizes that can accommodate a large amount of CO2 particles. The results of the experimental work show that excess adsorption results for gas mixtures lie in between the results for pure components. The simulation results agree with the experimental measurements. The strength of CO2 adsorption depends on both surface chemistry and pore size of activated carbon. Once strong adsorption sites within nanoscale network are established, gas adsorption even at very low pressure is governed by pore width rather than chemical composition. The outcomes of this paper provides new insights about the parameters affecting CO2 adsorption and storage in shale-gas reservoirs, which is critical for developing standalone representative models for CO2 adsorption on pure organic carbon.
more »
« less
Investigation of Ultramicroporous Structure of One-Dimensional Lepidocrocite Titanates Using Carbon Dioxide and Nitrogen Gases
The novel material, one-dimensional lepidocrocite (1DL) titanate, is attracting industrial and scientific interest because of its applicability to a wide range of practical applications and its ease of synthesis and scale up of production. In this study, we investigated the CO2 adsorption capability and pore structures of 1DL freeze-dried and lithium chloride washed air-dried powders. The synthesized 1DL was characterized by X-ray diffraction, Raman spectroscopy, and scanning electron microscopy. Using the constant-volume method, CO2 gas adsorption revealed that the 1DL exhibits type IV adsorption–desorption isotherms. The heats of adsorption obtained from the adsorption branches are lower than those obtained from the desorption branches. Brunauer–Emmett–Teller (BET) analysis, using N2 gas adsorption isotherms at 77 K showed that 1DL possesses 80.2 m2/g of BET specific surface area. Nonlocal density functional theory analysis indicated that two types of pores, meso-pores and ultramicro pores, exist in the 1DL freeze-dried powders. This work provides deep insights into the pore structures and CO2 adsorption mechanisms of 1DL powders.
more »
« less
- PAR ID:
- 10562226
- Publisher / Repository:
- American Chemical Society
- Date Published:
- Journal Name:
- Langmuir
- Volume:
- 40
- Issue:
- 32
- ISSN:
- 0743-7463
- Page Range / eLocation ID:
- 16929 to 16935
- Subject(s) / Keyword(s):
- adsorption granular materials isotherms materials oxides
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
null (Ed.)An original methodology is suggested for evaluating the pore size distribution in carbons in the wide range of micro- and mesopores from 0.385 to 10 nm from a single isotherm of high-pressure adsorption of CO2 at 273 K. The proposed method is based on the reference theoretical isotherms calculated by Monte Carlo simulations in model pores of slit and cylindrical geometry. The relationship between the pore size and the pore filling pressure is established. Special attention is given to predicting of the capillary condensation transitions in mesopores by using the meso-canonical ensemble (gauge cell) Monte Carlo simulations. The proposed technique is demonstrated and verified against the conventional N2 and Ar low temperature adsorption methods drawing on the example of micro-mesoporous carbons of the CMK family. Advantages and limitations of CO2 adsorption characterization of nanoporous materials are discussed and further improvements are proposed.more » « less
-
Adsorption-induced swelling occurs in a wide spectrum of natural and engineered porous materials. A key underlying mechanism is the monotonic reduction of solid-fluid surface energy upon fluid adsorption, which lowers the contractive adsorption stress and causes the porous skeleton to swell (Bangham and Fakhoury, 1928). Some mesoporous materials, however, deviate from the monotonic swelling pattern predicted by this mechanism, exhibiting an abrupt shrinkage at intermediate adsorbate partial pressures before swelling resumes and continues to full saturation. This behavior is commonly attributed to capillary condensation of the adsorbate from the vapor to the liquid phase within the pores. Understanding the stresses and the shrinkage induced by capillary condensation is critical in various industrial applications including micro-/nanofabrication, geotechnical engineering in collapsible soils, and sorption-driven actuation technologies. This work aims to develop a unified poromechanics theory that captures the full sequence of adsorption-induced deformation, including initial swelling, contraction during capillary condensation, and resumed expansion near full saturation. The formulation begins with a thermodynamic analysis of an unsaturated deformable porous solid acknowledging the energetics of the solid-fluid (sl), solid-vapor (sv), and liquid-vapor (lv) interfaces. The resulting free energy balance permits the simultaneous derivation of the liquid retention characteristics curve and the coupled mechanical effects driven by adsorption and partial saturation. Within this framework, two strategies for constructing constitutive relations are examined: one explicitly resolves the dynamic evolution of sl-sv-lv interfacial areas to emphasize the underlying physics, while the other partially lumps the surface energies into a macroscopic capillary potential to facilitate model calibration using standard laboratory tests. The models are evaluated using datasets from two markedly different solid-fluid systems: N2 gas adsorption on a hierarchical porous silica at 77 K and water adsorption on a carbon xerogel at 298 K. Both approaches effectively capture the complex, non-monotonic strain isotherms exhibited by the adsorbent. The adsorption-desorption hysteresis is also addressed in a thermodynamically consistent framework. The proposed theory demonstrates both robustness and unifying power in explaining the complex strain isotherms of porous materials along adsorption and desorption paths, covering the entire spectrum from vacuum-dry to fully liquid-saturated states.more » « less
-
Flexible metal-organic frameworks (MOF) can show exceptional selectivity and capacity for adsorption of CO2. The incorporation of CO2 into flexible MOFs that have Cu2+ coordination centers and organic pillar ligands is accompanied by a distortion of the framework lattice arising from chemical interactions between these components and CO2 molecules. CO2 adsorption yields a reproducible lattice expansion that is enabled by the rotation of the pillar ligands. The structures of Cu2(pzdc)2(bpy) and Cu2(pzdc)2(bpe), CPL-2 and CPL-5, were evaluated using in situ synchrotron x-ray powder diffraction at room temperature at CO2 gas pressures up to 50 atm. The structural parameters exhibit hysteresis between pressurization and depressurization. The pore volume within CPL-2 and CPL-5 increases at elevated CO2 pressure due to a combination of the pillar ligand rotation and the overall expansion of the lattice. Volumetric CO2 adsorption measurements up to 50 atm reveal adsorption behavior consistent with the structural results, including a rapid uptake of CO2 at low pressure, saturation above 20 atm, and hysteresis evident as a retention of CO2 during depressurization. A significantly greater CO2 uptake is observed in CPL-5 in comparison with predictions based on CO2 pressure-induced expansion of the pore volume available for adsorption, indicating that the flexibility of the CPL structures is a key factor in enhancing adsorption capacity.more » « less
-
Adsorption of organics on surfaces is important in both outdoor and indoor environments. Surfaces can serve as sinks for gas-phase species, act as reservoirs by emitting previously partitioned organics back into the gas phase, and can facilitate heterogeneous chemistry. We report here studies of the uptake and desorption energetics of gas-phase limonene, a volatile and widely-distributed monoterpene, on solid silica nanoparticles using a unique apparatus that allows for temperature programmed desorption (TPD) measurements of surface binding energies as well as Knudsen cell gas uptake measurements. A multiphase kinetic model was applied to these data to provide additional molecular-level understanding of the processes involved. TPD experiments yielded an average desorption energy of 47.5 ± 8.2 kJ mol-1 (±1s, sample standard deviation), the first direct experimental measurement of this parameter over a broad temperature range (150–320 K). Initial net uptake coefficients (0,net) range from (1.7 ± 0.3) ×10-3 (±1s) at 210 K to (2.3 ± 0.4) ×10-4 (±1s) at 250 K, reflecting increased rates of desorption with an increase in temperature combined with increased rates of diffusion and re-adsorption within the pores between adjacent silica nanoparticles. Effective Langmuir constants, which also reflect the effects of pore diffusion and re-adsorption, were determined from the uptake data and vary from (1.8–0.3)×10-13 cm3 molecule-1 over the same temperature range. These results are in excellent agreement with previous studies around room temperature and with theoretical calculations of the energetics of the limonene-silica interaction. The strong attraction between limonene and the polar silica surface shows the importance of including such interactions in models of the atmospheric fates of terpenes both indoors and outdoors.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1021/acs.langmuir.4c01689
