In this study, we measured the tensile, compression, and fatigue behavior of additively manufactured Ti3Al2V as a function of build orientation. Ti3Al2V alloy was prepared by mixing commercially pure titanium and Ti6Al4V in 1:1 wt. ratio. Laser powder bed fusion-based additive manufacturing technique was used to fabricate the samples. Tensile tests resulted in an ultimate strength of 989 ± 8 MPa for Ti3Al2V. Ti6Al4V 90° orientation samples showed a compressive yield strength of 1178 ± 33 MPa and that for Ti3Al2V 90° orientation samples were 968 ± 24 MPa. By varying the build orientation to account for anisotropy, Ti32 45° and Ti32 0° samples displayed almost similar compressive yield strength values of 1071 ± 16 and 1051 ± 18 MPa, respectively, which were higher than that of Ti32 90° sample. Fatigue loading revealed an endurance limit (10 million cycles) of 250 MPa for Ti6Al4V and of 219 MPa for Ti3Al2V built at 90° orientation. The effect of the build orientation was significant under fatigue loading; Ti3Al2V built at 45° and 0° orientations displayed endurance limits of 387.5 MPa and 512 MPa, respectively; more than two-fold increment in endurance limit was observed. In conclusion, the superior attributes of Ti3Al2V alloy over Ti6Al4V alloy, as demonstrated in this study, justify its potential in load-bearing applications, particularly for use in orthopedic devices.
This content will become publicly available on October 24, 2025
Laser powder bed fusion (LPBF) is an enabling process manufacture of complex metal components. However, LPBF is prone to generate geometrical defects (e.g., porosity, lack of fusion), which causes a significant fatigue scattering. However, LPBF fatigue scattering data and analysis in the literature are not only sparse and limited to tension-compression mode but also inconsistent. This article presents a robust high-frequency fatigue testing method to construct stress-cycle curves of SS 316L to understand the scattering nature and predict the scattering pattern. A series of bending fatigue tests are performed at different stress amplitudes. Two different runout criteria are used to investigate fatigue life, fatigue limits, and scattering. The endurance limit reaches around 300 MPa for the defect size distribution at the selected process space. The defect size-based fatigue limit model is found to underestimate the endurance limit by about 30 MPa when comparing with the experimental data. Fatigue scattering is further calculated by using 95% prediction intervals, showing that low fatigue scattering is present at high stresses while a large variation of fatigue life occurs at stresses near the knee point.
more » « less- Award ID(s):
- 2323083
- PAR ID:
- 10562826
- Publisher / Repository:
- ASME
- Date Published:
- Journal Name:
- Journal of Manufacturing Science and Engineering
- Volume:
- 147
- Issue:
- 2
- ISSN:
- 1087-1357
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
more » « less
-
Laser powder bed fusion (LPBF) has been increasingly used in the fabrication of dense metallic structures. However, the corrosion related properties of LPBF alloys, in particular environment-assisted cracking, such as corrosion fatigue properties, are not well understood. In this study, the corrosion and corrosion fatigue characteristics of LPBF 316L stainless steels (SS) in 3.5 wt.% NaCl solution have been investigated using an electrochemical method, high cycle fatigue, and fatigue crack propagation testing. The LPBF 316L SSs demonstrated significantly improved corrosion properties compared to conventionally manufactured 316L, as reflected by the increased pitting and repassivation potentials, as well as retarded crack initiation. However, the printing parameters did not strongly affect the pitting potentials. LPBF samples also demonstrated enhanced capabilities of repassivation during the fatigue crack propagation. The unique microstructural features introduced during the printing process are discussed. The improved corrosion and corrosion fatigue properties are attributed to the presence of columnar/cellular subgrains formed by dislocation networks that serve as high diffusion paths to transport anti-corrosion elements.more » « less
-
Understanding the fatigue behavior and accurately predicting the fatigue life of laser powder bed fusion (L-PBF) parts remain a pressing challenge due to complex failure mechanisms, time-consuming tests, and limited fatigue data. This study proposes a physics-informed data-driven framework, a multimodal transfer learning (MMTL) framework, to understand process-defect-fatigue relationships in L-PBF by integrating various modalities of fatigue performance, including process parameters, XCT-inspected defects, and fatigue test conditions. It aims to leverage a pre-trained model with abundant process and defect data in the source task to predict fatigue life nondestructive with limited fatigue test data in the target task. MMTL employs a hierarchical graph convolutional network (HGCN) to classify defects in the source task by representing process parameters and defect features in graphs, thereby enhancing its interpretability. The feature embedding learned from HGCN is then transferred to fatigue life modeling in neural network layers, enabling fatigue life prediction for L-PBF parts with limited data. MMTL validation through a numerical simulation and real-case study demonstrates its effectiveness, achieving an F1-score of 0.9593 in defect classification and a mean absolute percentage log error of 0.0425 in fatigue life prediction. MMTL can be extended to other applications with multiple modalities and limited data.more » « less
-
Electron Beam Melting (EBM) is a widespread additive manufacturing technology for metallic-part fabrication; however, final products can contain microstructural defects that reduce fatigue performance. While the effects of gas and keyhole pores are well characterized, other defects, including lack of fusion and smooth facets, warrant additional investigation given their potential to significantly impact fatigue life. Therefore, such defects were intentionally induced into EBM Ti-6Al-4V, a prevalent titanium alloy, to investigate their degradation on stress-controlled fatigue life. The focus offset processing parameter was varied outside of typical manufacturing settings to generate a variety of defect types, and specimens were tested under fatigue loading, followed by surface and microstructure characterization. Fatigue damage primarily initiated at smooth facet sites or sites consisting of un-melted powder due to a lack of fusion, and an increase in both fatigue life and void content with increasing focus offset was noted. This counter-intuitive relationship is attributed to lower focus offsets producing a microstructure more prone to smooth facets, discussed in the literature as being due to lack of fusion or cleavage fracture, and this study indicates that these smooth flaws are most likely a result of lack of fusion.more » « less
-
more » « less
Abstract Four different experimental approaches for rapid estimation of fatigue limit (endurance limit) based on energy dissipation during cyclic loading are discussed. The presented approaches use energy dissipation and thermography and can reliably evaluate the fatigue limit of material by conducting the fatigue test on a single specimen. Results show that the released energy due to damage accumulation at the stress levels above the fatigue limit changes the trend of energy dissipation and that this trend can be used to predict the fatigue limit. Experimental results on CS 1018 and SS 304 specimens are presented to illustrate the utility of the proposed methods.
