An official website of the United States government
The study of plant electrophysiology offers promising techniques to track plant health and stress in vivo for both agricultural and environmental monitoring applications. Use of superficial electrodes on the plant body to record surface potentials may provide new phenotyping insights. Bacterial nanocellulose (BNC) is a flexible, optically translucent, and water-vapor-permeable material with low manufacturing costs, making it an ideal substrate for non-invasive and non-destructive plant electrodes. This work presents BNC electrodes with screen-printed carbon (graphite) ink-based conductive traces and pads. It investigates the potential of these electrodes for plant surface electrophysiology measurements in comparison to commercially available standard wet gel and needle electrodes. The electrochemically active surface area and impedance of the BNC electrodes varied based on the annealing temperature and time over the ranges of 50 °C to 90 °C and 5 to 60 min, respectively. The water vapor transfer rate and optical transmittance of the BNC substrate were measured to estimate the level of occlusion caused by these surface electrodes on the plant tissue. The total reduction in chlorophyll content under the electrodes was measured after the electrodes were placed on maize leaves for up to 300 h, showing that the BNC caused only a 16% reduction. Maize leaf transpiration was reduced by only 20% under the BNC electrodes after 72 h compared to a 60% reduction under wet gel electrodes in 48 h. On three different model plants, BNC–carbon ink surface electrodes and standard invasive needle electrodes were shown to have a comparable signal quality, with a correlation coefficient of >0.9, when measuring surface biopotentials induced by acute environmental stressors. These are strong indications of the superior performance of the BNC substrate with screen-printed graphite ink as an electrode material for plant surface biopotential recordings.
more »
« less
Development of nanowire-modified electrodes applied in the locally enhanced electric field treatment (LEEFT) for water disinfection
The desired properties, potential synthesis strategies, and an evaluation guideline of the electrodes are discussed with the review of the existing electrodes.
more »
« less
- Award ID(s):
- 1845354
- PAR ID:
- 10581390
- Publisher / Repository:
- The Royal Society of Chemistry
- Date Published:
- Journal Name:
- Journal of Materials Chemistry A
- Volume:
- 8
- Issue:
- 25
- ISSN:
- 2050-7488
- Page Range / eLocation ID:
- 12262 to 12277
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
ABSTRACT Despite their high power density, microsupercapacitors (MSCs) are impractical for many energy storage applications due to their limited energy density. Their energy density can be increased by shaping the electrodes into 3D structures with high specific surface area (SSA). Direct printing of nanoporous 3D electrodes is a promising approach for achieving high SSA. However, conventional nanoscale 3D printing is too slow due to point‐by‐point processing. Here, we have employed the projection two‐photon lithography technique to fabricate nanoporous 3D electrodes via a rapid layer‐by‐layer mechanism. The 3D MSC electrodes are engineered as an array of nanoporous polymeric micropillars that are printed with customizable spacing and count over a 0.25 cm2area. After printing, these micropillars are conformally coated with titanium nitride to form conductive 3D electrodes, which exhibit a specific capacitance of 361 μF/cm2. This is two orders of magnitude higher than the capacitance of the flat surface and exceeds the capacitance of both traditional bare electrodes, such as single‐wall carbon nanotubes (< 100 μF/cm2), and electrodes produced by photo‐polymerization 3D printing (˜200 μF/cm2). As our work demonstrates that high energy density 3D electrodes can be rapidly fabricated, it significantly expands the utility of MSCs as miniaturized energy storage devices.more » « less
-
Abstract Organic batteries are one of the possible routes for transitioning to sustainable energy storage solutions. However, the recycling of organic batteries, which is a key step toward circularity, is not easily achieved. This work shows the direct recycling of poly(2,2,6,6‐tetramethylpiperidinyloxy‐4‐yl) (PTMA) and poly(2,2,6,6‐tetramethylpiperidinyloxy‐4‐yl acrylamide) (PTAm) based composite electrodes. After charge‐discharge cycling, the electrodes are deconstructed using a solubilizing‐solvent and then reconstructed using a casting‐solvent. The electrochemical properties of the original and recycled electrodes are compared using cyclic voltammetry (CV) and galvanostatic charge‐discharge (GCD) cycling, from which it is discovered using time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) that recycling can be challenged by the formation of a cathode electrolyte interphase (CEI). In turn, an additive is proposed to modify the CEI layer and improve the properties after recycling. Last, an anionic rocking chair battery consisting of PTAm electrodes as both positive and negative electrodes is demonstrated, in which the electrodes are recycled to form a new battery. This work demonstrates the recycling of composite electrodes for organic batteries and provides insights into the challenges and possible solutions for recycling the next‐generation electrochemical energy storage devices.more » « less
-
Abstract Dielectric elastomer actuators (DEAs) exhibit fast actuation and high efficiencies, enabling applications in optics, wearable haptics, and insect-scale robotics. However, the non-uniformity and high sheet resistance of traditional soft electrodes based on nanomaterials limit the performance and operating frequency of the devices. In this work, we computationally investigate electrodes composed of arrays of stiff fiber electrodes. Aligning the fibers along one direction creates an electrode layer that exhibits zero stiffness in one direction and is predicted to possess high and uniform sheet resistance. A comprehensive parameter study of the fiber density and dielectric thickness reveals that the fiber density primary determines the electric field localization while the dielectric thickness primarily determines the unit cell stiffness. These trends identify an optimal condition for the actuation performance of the aligned electrode DEAs. This work demonstrates that deterministically designed electrodes composed of stiff materials could provide a new paradigm with the potential to surpass the performance of traditional soft planar electrodes.more » « less
-
Abstract Solid‐state batteries with alloy‐type negative electrodes can feature enhanced energy density and safety compared to conventional Li‐ion batteries. However, diffusional Li trapping within Li alloys often causes low initial Coulombic efficiency and leads to capacity loss with cycling. Here, a general roll‐pressing prelithiation method compatible with a variety of alloy‐type negative electrodes (silicon, aluminum, tin, and multi‐phase alloys) is introduced, which is shown to improve performance in solid‐state batteries. By warm‐rolling lithium foil of controlled thickness with various alloy‐type electrodes, both slurry‐cast and foil‐type electrodes can be uniformly prelithiated via direct chemical reaction. The prelithiated electrodes exhibit enhanced specific capacity and extended cycle life in batteries with Li6PS5Cl solid‐state electrolyte. Prelithiated multi‐phase foil electrodes with a tailored interface are shown to exhibit superior cycling stability down to 2 MPa stack pressure. This prelithiation technique offers a pathway to overcome intrinsic challenges in alloy anodes for solid‐state batteries.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript1.0
- Journal Article:
- https://doi.org/10.1039/D0TA03750H
