An official website of the United States government
A multiline ring anchor (MRA) system has been developed as a cost-effective alternative for securing arrays of floating offshore wind turbines (FOWTs) to the seabed. Multiline attachments can improve the economically competitiveness of FOWTs by reducing the capital cost of the support system for the floating structures. FOWTs can be subjected to severe wind and wave conditions resulting in extreme loads to the anchor system. Thus, the reliable design of the anchor system requires proper determination of the extreme mooring line loads acting on the anchor needed to secure FOWTs to the seabed. Previous studies showed the MRA in soft clay has clear advantages over existing anchors under the extreme horizontal loading conditions imposed by catenary moorings; however, its performance relative to conventional anchors under extreme vertical loading imposed by taut mooring systems requires further investigation. This study presents predictions of extreme loads on floating structures secured by taut mooring systems and evaluates the potential for developing an economical anchor for resisting these extreme loads.
more »
« less
Centrifuge Modeling of the Monotonic Capacity of Offshore Ring Anchors in Sand
The development of offshore wind technology has become a feasible solution to meet the increasing demands for clean and renewable energy. The United States has a total of 4250GW offshore wind energy potential; however, 65% of it is in deep water zones (Lopez et al., 2022) where wind turbines with fixed foundations typically are economically and technically unfeasible. In those situations, floating turbines supported by subsea anchors are a more competitive solution. Based on previous studies, ring anchors can be more material-efficient than piles and caissons because they require less material. Ring anchors also perform better than drag anchors due to their greater embedment depth. To further understand the behavior of ring anchors in saturated sand, a series of centrifuge load tests were performed at the University of California Davis Center for Geotechnical Modeling (CGM) at an acceleration of 70g. This test series investigated the effect of the anchor embedment depth and loading angle on the monotonic loading behavior. The ring anchor models were embedded in dense saturated sand, and then connected to an actuator using taut steel wire ropes. Sensors were used to measure the line tension, displacement, and inclination. The results indicate that the ring anchors mobilize greater capacities as their embedment depth is increased and when they are loaded at angles close to the horizontal direction, while vertical loading leads to the smallest capacity. The anchor displacement during the tests deviated slightly from the loading direction, showing a horizontal deviation at the earlier stages of the tests and a vertical one after the peak load. Furthermore, soil disturbance induced by the anchor installation was found to have a strong effect on the vertical capacity of the ring anchors. Overall, this study provides valuable information regarding the monotonic loading behavior of ring anchors which can aid in their future field deployment.
more »
« less
- Award ID(s):
- 1942369
- PAR ID:
- 10582516
- Publisher / Repository:
- Deep Foundations Institute
- Date Published:
- Journal Name:
- DFI Journal The Journal of the Deep Foundations Institute
- Volume:
- 18
- Issue:
- 1
- ISSN:
- 1937-5247
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
A multiline ring anchor (MRA) system has been developed as a cost-effective alternative for securing arrays of floating offshore wind turbines (FOWTs) to the seabed. Multiline attachments can improve the economically competitiveness of FOWTs by reducing the capital cost of the support system for the floating structures. FOWTs can be subjected to severe wind and wave conditions resulting in extreme loads to the anchor system. Thus, the reliable design of the anchor system requires proper determination of the extreme mooring line loads acting on the anchor needed to secure FOWTs to the seabed. Previous studies showed the MRA in soft clay has clear advantages over existing anchors under the extreme horizontal loading conditions imposed by catenary moorings; however, its performance relative to conventional anchors under extreme vertical loading imposed by taut mooring systems requires further investigation. This study presents predictions of extreme loads on floating structures secured by taut mooring systems and evaluates the potential for developing an economical anchor for resisting these extreme loads.more » « less
-
The multiline ring anchor (MRA) was devised as a cost-effective means for securing floating offshore wind turbines (FOWTs) to the seabed. FOWTs occurring in arrays create the possibility for attaching mooring lines from multiple units to a single anchor. Additionally, the deep embedment of the MRA into relatively strong soil permits high load capacity to be achievable with a small and lighter anchor, thereby reducing anchor material, transport, and installation costs. However, since the MRA is shorter than a conventional caisson, features such as wing plates and keying flaps are needed to achieve parity in load capacity with a caisson having a comparable diameter. Preliminary studies show that attaching wing plates to MRA in soft clay is highly effective in enhancing its horizontal load capacity, but only marginally effective in improving vertical load capacity. This motivated the current study investigating the use of keying flaps to further enhance vertical load capacity. Two-dimensional finite element analyses were conducted to understand how keying flaps impact on the failure mechanism of the stiffeners and provide reliable evaluations of the uplift resistance of the MRA. The results show that the thickness of the stiffener, flap length, and flap angle can affect the failure mechanism and bearing factors. For the optimal design of the stiffener, a comparative study was carried out to compare the effects of keying flaps and thickness of the stiffener. The studies show that introducing keying flaps can have comparable load capacity with thicker stiffeners, and that it can be an economical solution for achieving high vertical load capacity while containing material and fabrication costs.more » « less
-
The multiline ring anchor (MRA) was devised as a cost-effective means for securing floating offshore wind turbines (FOWTs) to the seabed. FOWTs occurring in arrays create the possibility for attaching mooring lines from multiple units to a single anchor. Additionally, the deep embedment of the MRA into relatively strong soil permits high load capacity to be achievable with a small and lighter anchor, thereby reducing anchor material, transport, and installation costs. However, since the MRA is shorter than a conventional caisson, features such as wing plates and keying flaps are needed to achieve parity in load capacity with a caisson having a comparable diameter. Preliminary studies show that attaching wing plates to MRA in soft clay is highly effective in enhancing its horizontal load capacity, but only marginally effective in improving vertical load capacity. This motivated the current study investigating the use of keying flaps to further enhance vertical load capacity. Two-dimensional finite element analyses were conducted to understand how keying flaps impact the failure mechanism of the stiffeners and provide reliable evaluations of the uplift resistance of the MRA. The results show that the thickness of the stiffener, flap length, and flap angle can affect the failure mechanism and bearing factors. For the optimal design of the stiffener, a comparative study was carried out to compare the effects of keying flaps and thickness of the stiffener. The studies show that introducing keying flaps can have comparable load capacity with thicker stiffeners and that it can be an economical solution for achieving high vertical load capacity while containing material and fabrication costs.more » « less
-
Offshore foundation elements are often subjected to cycles of compressive and tensile loading. Open-ended pipe piles are frequently used as foundations for wind turbines as monopiles or as part of jacket structures. This paper reports the results of two open-ended pipe pile tests in a half-cylindrical calibration chamber with image analysis capabilities. The model piles, with diameters of 44 mm and 63 mm, were jacked into dense silica sand samples, statically load tested in compression, cyclically load tested (under displacement-controlled conditions), and statically load tested in compression a second time. The cyclic load tests had 100 cycles with a half-amplitude of 1 mm. Digital images captured during testing were analysed using digital image correlation to obtain the displacement fields in the soil domain. Image analyses of compressive static load tests indicate that the soil plug undergoes vertical compression during static loading. Cyclic loading leads to shaft resistance degradation, which is correlated with contractive radial strains around the model pile. Cycling also causes vertical compression below the pile base and inside the soil plug, which increases the base resistance of the piles and ultimately increases the total compressive capacity of the model open-ended piles under static loading.more » « less
- Free Publicly Accessible Full Text
-
Accepted Manuscript
- Journal Article:
- https://doi.org/10.37308/DFIJnl.20230915.297
