An official website of the United States government
Abstract Hydraulic fracturing of oil and gas wells is a water intensive process. Limited availability, cost and increasing government regulations restraining the use and disposal of fresh water have led to the need for alternative fracturing fluids. Using CO2 foam as a fracturing fluid can drastically reduce the need for water in hydraulic fracturing. We address the addition of polyelectrolyte complex nanoparticles (PECNP) to surfactant solutions to improve foam stability, durability and rheological properties at high foam qualities. Polyelectrolyte pH and polyanion/polycation ratios were varied to minimize particle size and maximize absolute zeta potential of the resulting nanoparticles. Rheological tests were conducted on foam systems of varying surfactant/PECNP ratios and different foam quality to understand the effect of shear on viscosity under simulated reservoir conditions of 40°C and 1300 psi. The same foam systems were tested for stability and durability in a view cell at reservoir conditions. Supercritical CO2 foam generated by surfactant alone resulted in short lived, low viscosity foam because of surfactant drainage from foam lamellae. However, addition of PECNP strengthens the foam film by swelling the film due to increased osmotic pressure and electrostatic forces. Electrostatic interactions reduce dynamic movement of surfactant micelles, thereby stabilizing the foam lamellae, which imparts high durability and viscosity to supercritical CO2 foams. From the rheology test results, it was concluded that increasing foam quality and the presence of PECNP resulted in improved viscosity. Also, foam systems with PECNP showed promising results compared with foam generated using surfactant alone in the view cell durability test. The addition of optimized polyelectrolyte nanoparticles to the surfactant can improve viscosity and durability of supercritical CO2 foam during hydraulic fracturing, which can lead to large reductions in water requirements.
more »
« less
This content will become publicly available on February 5, 2026
Shear thickening inside elastic open-cell foams under dynamic compression
Dynamic compression of elastic foam filled with non-Newtonian fluid can be rationalized by fluid rheology and foam pore size distribution.
more »
« less
- Award ID(s):
- 2011854
- PAR ID:
- 10590191
- Publisher / Repository:
- The Royal Society of Chemistry
- Date Published:
- Journal Name:
- Soft Matter
- Volume:
- 21
- Issue:
- 6
- ISSN:
- 1744-683X
- Page Range / eLocation ID:
- 1192 to 1202
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract Articular cartilage is a thin layer of a solid matrix swollen by fluid, and it protects joints from damage via poroviscoelastic damping. Our previous experimental and simulation studies showed that cartilage-like poroviscoelastic damping could widen the range of damping methods in a low-frequency range (<100 Hz). Thus, the current study aimed to realize cartilage-like damping capacity by single- and two-indenter–foam poroviscoelastic dampers in a low-frequency range. Multiple single-indenter–foam dampers were designed by combining foam sheets with different pore diameters and indenters with different radii. Their damping capacity was investigated by dynamic mechanical analysis in a frequency range of 0.5–100 Hz. Single-indenter–foam dampers delivered peak damping frequencies that depended on the foam’s pore diameter and characteristic diffusion length (contact radii). Those dampers maximize the damping capacity at the desired frequency (narrowband performance). A mechanical model combined with simple scaling laws was shown to relate poroelasticity to the peak damping frequencies reasonably well. Finally, combinations of single-indenter–foam dampers were optimized to obtain a two-indenter–foam damper that delivered nearly rate-independent damping capacity within 0.5–100 Hz (broadband performance). These findings suggested that cartilage-like poroviscoelastic dampers can be an effective mean of passive damping for narrowband and broadband applications.more » « less
-
We study the structure and dynamics of the interface separating a passive fluid from a microtubule-based active fluid. Turbulent-like active flows power giant interfacial fluctuations, which exhibit pronounced asymmetry between regions of positive and negative curvature. Experiments, numerical simulations, and theoretical arguments reveal how the interface breaks up the spatial symmetry of the fundamental bend instability to generate local vortical flows that lead to asymmetric interface fluctuations. The magnitude of interface deformations increases with activity: In the high activity limit, the interface self-folds invaginating passive droplets and generating a foam-like phase, where active fluid is perforated with passive droplets. These results demonstrate how active stresses control the structure, dynamics, and break-up of soft, deformable, and reconfigurable liquid–liquid interfaces.more » « less
-
Densely packed wet foam was subjected to gradual expansion and contraction in a wide (1400–1800 μm) microfluidic channel to study localized plastic deformation events within the monodisperse bubble matrix. Dislocation glide, reflection, nucleation, and dipole transformations from extensional and compressive stresses were observed across a range of fluid flow rates and bubble packing densities. Disparate, cyclic reflections occur in two independent regions of the flowing foam, and the mechanisms of dislocation reflection under tension are expanded. The use of an asymmetric channel created a dichotomy in the model crystalline system between straighter, aligned bubble rows and curved, misaligned rows due to the corresponding streamlines within the channel. The resulting gradient in crystalline alignment had numerous effects on dislocation mobility and plastic deformation. 7/7 dipoles were found to rearrange to a more stable configuration aligned with the foam flow before dissociating. Dislocations comprising 5/5 dipoles (resembling the inverse-Stone–Wales defect in carbon nanostructures) were discovered to pass through one another via intermediate ring structures, which most commonly consisted of three dislocation pairs around a triangular-shaped central bubble.more » « less
