Abstract During drying, liquid‐applied particulate coatings develop stress and are consequently prone to stress‐induced defects, such as cracking, curling, and delamination. In this work, the stress development and cracking of coatings, prepared from aqueous silica and zinc oxide particle suspensions, were characterized using cantilever beam deflection with simultaneous imaging of the coating surface. Drying uniformity was improved and lateral or edge‐in drying was discouraged by using thin silicone walls around the perimeter of the cantilever. Coatings prepared from larger monodisperse silica particles (D50∼ 0.9 µm) dried uniformly but had a high critical cracking thickness (>150 µm) that prevented simultaneous study of stress development and cracking. Coatings prepared from smaller silica particles (D50∼ 0.3 µm) cracked readily at low thicknesses but exhibited edge‐in drying that complicated the stress measurement data. This drying nonuniformity was connected to the potential for these small particles to accumulate at the coating surface during drying. Hence, the selection of particle size and density was critical to drying uniformity when characterizing stress development and cracking. Coatings prepared from suspensions of zinc oxide particles (D50∼ 0.4 µm) were well‐suited for these studies, with uniform drying stress peaking at ∼1 MPa. Characteristic features in the stress development data above and below the critical cracking thickness (53 µm) were identified, demonstrating that cantilever beam deflection is a useful tool for studying the effectiveness of crack mitigation methods and the fundamentals of coating fracture during drying.
more »
« less
Bioinspired SiC/Chitosan Impact Resistant Coatings
Abstract Routine high strain rate impacts from the surrounding environment can cause surface erosion, abrasion, and even catastrophic failure to many structural materials. It is thus highly desirable to develop lightweight, thin, and tough impact resistant coatings. Here, inspired by the structurally robust impact surface of the dactyl club of the peacock mantis shrimp, a silicon carbide and chitosan nanocomposite coating is developed to evaluate its impact resistance as a function of particle loading. High strain rate impact tests demonstrate that coatings with 50% and 60% SiC have optimal performance with the greatest reduction in penetration depth and damage area to the substrate. Post‐impact analysis confirms that these concentrations achieve a balance between stiffness and matrix phase continuity, efficiently dissipating impact energy while maintaining coating integrity. The addition of SiC particles helps dissipate impact energy via interphase effects, particle percolation, and frictional losses due to particle jamming. The formation of these stress paths is also modeled to better understand how the addition of particles improves coating stiffness and the stress distribution as a function of particle loading. These findings highlight the potential of bioinspired materials and their promise to promote innovation and breakthroughs in the development of resilient multifunctional materials.
more »
« less
- Award ID(s):
- 2011967
- PAR ID:
- 10590625
- Publisher / Repository:
- Wiley
- Date Published:
- Journal Name:
- Advanced Functional Materials
- Volume:
- 35
- Issue:
- 11
- ISSN:
- 1616-301X
- Subject(s) / Keyword(s):
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Abstract The mechanical behavior of 3D printed polymeric materials is critical for applications in additive manufacturing, soft robotics, biomedical devices, and mechanical metamaterial designs. This study investigates the strain rate-dependent mechanical behaviors 3D printed polymers fabricated using a multi-material 3D printer (Stratasys Connex 3) through systematic mechanical experiments under a large range of strain rate from 10−2 to 103 s−1. Quasi-static indentation tests were conducted to evaluate deformation and failure under localized static loading, while dynamic puncture and compression tests were conducted via a drop tower (Zwick Amsler HIT600F) to characterize energy absorption and bulk properties under impact. To characterize rate-dependent constitutive relation, both quasi-static compression and Split Hopkinson Pressure Bar (SHPB) tests were conducted. The results show increased stiffness and yielding stress for higher strain rates, alongside a transition from ductile to brittle-like failure modes. These findings enhance the understanding of mechanical behaviors of 3D printed polymers under dynamic loading, offering critical data for material modeling and structural design in high-performance applications. The work informs the development of reliable computational models and optimizes additive manufacturing for impact-resistant designs.more » « less
-
Abstract In this study, we demonstrate a novel environmental barrier coating processed from polymer‐derived ceramics (PDCs) with homogeneously distributed sub‐micrometer Y2O3as the filler. Under suitable conditions, dense and crack‐free coatings can be achieved for all the designed compositions with the volumetric content of Y2O3varied from 45 to 93 vol%. To process the PDC SiC–Y2O3composite coatings, Y2O3particles and SiC liquid precursor were uniformly dispersed in hexane and then dip‐coated on SiC substrates. After cross‐linking at 250°C and heat‐treated at 900°C in argon, dense and crack‐free PDC SiC–Y2O3composite coatings were formed. The effect of coating thickness and heat‐treatment temperature on the formation of cracks due to constrained pyrolysis was studied. The critical thickness for realizing crack‐free coatings of three compositions (i.e., 93, 77, and 45 vol% Y2O3) was studied for heat treatment from 1000 to 1300°C using atomic force microscope and scanning electron microscopy. As heat‐treatment temperature increases, the critical coating thickness decreases for the same coating compositions due to enhanced shrinkage at higher temperature. With higher Y2O3content, the critical thickness of the coating increased. The inert Y2O3particles reduce the amount of polymer leading to reduction in the overall constrained shrinkage of the coating during heat treatment.more » « less
-
Abstract Carbon nanotube sponges (CNSs) are ultra-light, highly porous materials with significant potential for advanced engineering applications. Despite their promising characteristics—including high surface area, low density, and an interconnected carbon network—their mechanical behavior, particularly under tensile loading, remains poorly understood. This study investigates the tensile properties of CNSs to evaluate their strength, flexibility, and deformation mechanisms. To characterize their mechanical response, thin CNS samples were subjected to uniaxial tensile testing using a nano-tensile testing system. Stress–strain curves were obtained to extract key parameters, including Young’s modulus, ultimate tensile strength, and elongation at break. The results provide valuable insights into the elastic and failure behavior of CNSs, establishing a foundational understanding of their mechanical performance. These findings contribute to the broader effort to integrate CNSs into next-generation technologies, including impact-resistant coatings, flexible electronics, and high-performance composites. By establishing a baseline for tensile performance, this work enables the targeted optimization of CNS structures for specific applications. Overall, this study represents an important step toward realizing the full potential of CNSs in advanced materials systems.more » « less
-
This paper presents the initial developments of a framework for modeling the compression behavior of coarse-grained soil using 3D printed particle analogs. This framework consists of a newly developed normalization scheme for 1-D compression response based on Hertz contact theory. The scheme normalizes the differences in stiffness of the natural and 3D printed particles’ constituent materials. To explore the capabilities of the proposed framework, this paper presents results of 1D compression tests on assemblies composed of spherical particles of constituent materials with Young’s moduli that span over two orders of magnitude (steel, glass and 3D printed resin). These initial results indicate that the stress-strain behavior of the assemblies can be normalized to be independent of constituent material stiffness. The presented framework can be useful for modeling the behavior of natural soil by testing representative 3D printed analogs, provided that the different aspects of the soils, such as particle shape, size, surface roughness and gradation are properly reproduced.more » « less
An official website of the United States government

