An official website of the United States government
As high-strength aluminum alloys present several processability issues with additive manufacturing (AM), Scalmalloy®, an Al-Mg-Sc-Zr-based alloy, has been developed. This alloy is age-hardenable, allowing it to precipitate out a strengthening precipitate phase, Al3(Sc,Zr). The manufacturer recommends a single-stage aging treatment at 325 °C for 4 h; however, the majority of the literature studies utilize a powder bed processing known as selective laser melting (SLM) over powder-fed processing directed energy deposition (DED). This study addresses the lack of information on heat treatments for DED fabrication by exploring the application of artificial aging temperatures of 300–400 °C for 2, 4, and 6 h to: 1. determine the impact on the microstructural evolution and mechanical performance and 2. determine whether the recommended treatment for Scalmalloy® is appropriate for DED fabrication. Tensile testing determined that low-temperature treatments exhibited no visible dependence on time (2–6 h); however, time becomes influential at higher temperatures starting at 350 °C. The temperature plays a considerable role in the mechanical and microstructural behaviors of DED Scalmalloy®. The highest tensile strength was noted at 300 °C (384 MPa, 21.6% increase), but all heat-treated cases resulted in an improvement over the as-built case. This investigation established that increasing the treatment temperature resulted in a decreasing trend for the tensile strength that held over time. Elongation at 2 h displayed a near parabolic trend that peaks at 350 °C (20%) and falls with higher temperatures. At the 4 h treatment, a slight decreasing trend was noticed for elongation. No visible change was observed for elongation at 6 h, with elongation values remaining fairly consistent. The microstructural evolution, including micron-sized and nano-sized Al3(Sc,Zr) and grain size, was examined, and coarsening effects were noted with the increase in the temperature. It is recommended that treatment be conducted at 300 °C to achieve the precipitation of the strengthening Al3(Sc,Zr) phase while minimizing coarsening.
more »
« less
Evidence of non-isentropic release from high residual temperatures in shocked metals measured with ultrafast x-ray diffraction
Shock experiments are widely used to understand the mechanical and electronic properties of matter under extreme conditions. However, after shock loading to a Hugoniot state, a clear description of the post-shock thermal state and its impacts on materials is still lacking. We used diffraction patterns from 100-fs x-ray pulses to investigate the temperature evolution of laser-shocked Al–Zr metal film composites at time delays ranging from 5 to 75 ns driven by a 120-ps short-pulse laser. We found significant heating of both Al and Zr after shock release, which can be attributed to heat generated by inelastic deformation. A conventional hydrodynamic model that employs (i) typical descriptions of Al and Zr mechanical strength and (ii) elevated strength responses (which might be attributed to an unknown strain rate dependence) did not fully account for the measured temperature increase, which suggests that other strength-related mechanisms (such as fine-scale void growth) could play an important role in thermal responses under shock wave loading/unloading cycles. Our results suggest that a significant portion of the total shock energy delivered by lasers becomes heat due to defect-facilitated plastic work, leaving less converted to kinetic energy. This heating effect may be common in laser-shocked experiments but has not been well acknowledged. High post-shock temperatures may induce phase transformation of materials during shock release. Another implication for the study is the preservability of magnetic records from planetary surfaces that have a shock history from frequent impact events.
more »
« less
- Award ID(s):
- 2049620
- PAR ID:
- 10593639
- Author(s) / Creator(s):
- ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; more »
- Publisher / Repository:
- American Institute of Physics
- Date Published:
- Journal Name:
- Journal of Applied Physics
- Volume:
- 136
- Issue:
- 5
- ISSN:
- 0021-8979
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
The thermo-mechanical behavior of saturated clays during a heating/cooling cycle is relevant from the perspective of understanding different types of energy geostructures as well as understanding the use of heat for soil improvement. This paper involves a study of the effect of a heating/cooling cycle on the preconsolidation stress of saturated normally consolidated clays. Although many studies have observed a decrease in preconsolidation stress (thermal softening) after heating of overconsolidated soils, fewer studies have investigated changes in preconsolidation stress of normally consolidated soils. Available thermo-elasto-plastic models indicate that a heating-cooling cycle will lead to thermal contraction and an apparent overconsolidation effect for normally consolidated soils (thermal hardening), but inconsistencies in the literature have been observed. This study involves the use of a thermal triaxial cell to first consolidate kaolinite clay to normally consolidated conditions, apply a drained heating or a heating/cooling cycle, followed by mechanical loading to higher mean effective stresses. The tests presented in this study confirm that cooling also induces an apparent overconsolidation effect on the initially normally consolidated clay, but with a preconsolidation stress greater than that expected from the initial virgin consolidation line before heating. The results are a positive finding regarding the possible use of heat to improve the mechanical response of soft clays.more » « less
-
Upon laser irradiation, 2D materials experience a cascading energy transfer from electrons to optical phonons (OPs) and then to acoustic phonons (APs), resulting in a significant thermal non-equilibrium among energy carriers. This non-equilibrium presents challenges for Raman-based thermal characterization, as Raman scattering measures only OP temperature rise, while APs are the primary energy carriers. Despite recent efforts to address this issue, OP–AP thermal non-equilibrium in supported 2D materials remains poorly resolved. Here, we develop a method to distinguish the OP and AP temperature rises based on their different temporal thermal responses under laser irradiation: the OP–AP temperature difference responds almost immediately (∼a few to tens of ps), while the AP temperature rise takes longer to establish (∼tens of ns). Using energy transport-state resolved Raman, we probe the transient thermal response of Si-supported nm-thick MoS2from 20 to 100 ns. We find that the OP–AP temperature difference exceeds 120% of the AP temperature rise under ∼0.439 µm radius laser heating. The intrinsic interfacial thermal conductance of the samples, based on the true AP temperature rise, varies from 0.199 to 1.46 MW·m−2·K−1, showing an increasing trend with sample thickness.more » « less
-
Abstract Shape memory alloys (SMAs) absorb and release large amounts of latent heat during martensitic transformation, making them ideal candidates for applications involving thermal energy storage and management. In this study, Cu–Zn–Al SMAs were investigated as lower-cost alternatives to NiTi-based SMAs for solid–solid phase change materials. The alloys were fabricated using an unconventional method of melting and solidification of the constituent elements sealed in quartz tubes under a pressurized Ar atmosphere. The alloys synthesized were found to exhibit superior figure of merit values for thermal energy storage, as compared to conventional solid–liquid phase change materials and NiTi-based SMAs, with thermal conductivity between 59 and 75 W/mK and latent heat values ranging from 3 to 6.5 J/g. Transformation temperature ranges (Af–Mf) less than 20 °C were achieved within a wide operating temperature between − 145 °C and 100 °C. In addition, select CuZnAl compositions yielded excellent cyclic stability with only ± 2 °C shifts in transformation temperatures after 20 thermal cycles. The present study demonstrates the feasibility of CuZnAl SMAs for use in high heat flux thermal energy storage and management applications at a wider range of temperatures.more » « less
-
Selective laser melting (SLM) is one of the most widely used additive manufacturing technologies. Fabricating nickel-based superalloys with SLM has garnered significant interest from the industry and the research community alike due to the excellent high temperature properties and thermal stability exhibited by the alloys. Haynes-282 alloy, a γ′-phase strengthened Ni-based superalloy, has shown good high temperature mechanical properties comparable to alloys like R-41, Waspaloy, and 263 alloy but with better fabricability. A study and comparison of the effect of different heat-treatment routes on microstructure and mechanical property evolution of Haynes-282 fabricated with SLM is lacking in the literature. Hence, in this manuscript, a thorough investigation of microstructure and mechanical properties after a three-step heat treatment and hot isostatic pressing (HIP) has been conducted. In-situ heat-treatment experiments were conducted in a transmission electron microscopy (TEM) to study γ′ precipitate evolution. γ′ precipitation was found to start at 950 °C during in-situ heat-treatment. Insights from the in-situ heat-treatment were used to decide the aging heat-treatment for the alloy. The three-step heat-treatment was found to increase yield strength (YS) and ultimate tensile strength (UTS). HIP process enabled γ′ precipitation and recrystallization of grains of the as-printed samples in one single step.more » « less
