An official website of the United States government
The transmission interference fringe (TIF) technique was developed to visualize the dynamics of evaporating droplets based on the Reflection Interference Fringe (RIF) technique for micro-sized droplets. The geometric formulation was conducted to determine the contact angle (CA) and height of macro-sized droplets without the need for the prism used in RIF. The TIF characteristics were analyzed through experiments and simulations to demonstrate a wider range of contact angles from 0 to 90°, in contrast to RIF's limited range of 0–30°. TIF was utilized to visualize the dynamic evaporation of droplets in the constant contact radius (CCR) mode, observing the droplet profile change from convex-only to convex-concave at the end of dry-out from the interference fringe formation. The TIF also observed the contact angle increase from the fringe radius increase. This observation is uniquely reported as the interference fringe (IF) technique can detect the formation of interference fringe between the reflection from the center convex profile and the reflection from the edge concave profile on the far-field screen. Unlike general microscopy techniques, TIF can detect far-field interference fringes as it focuses beyond the droplet-substrate interface. The formation of the convex-concave profile during CCR evaporation is believed to be influenced by the non-uniform evaporative flux along the droplet surface.
more »
« less
Investigating the origin of the far-field reflection interference fringe (RIF) of microdroplets
We show that the reflection interference fringe (RIF) is formed on a screen far away from the microdroplets placed on a prism-based substrate, which have low contact angles and thin droplet heights, caused by the dual convex–concave profile of the droplet, not a pure convex profile. The geometric formulation shows that the interference fringes are caused by the optical path difference when the reflected rays from the upper convex profile at the droplet–air interface interfere with reflection from the lower concave profile at oblique angles lower than the critical angle. Analytic solutions are obtained for the droplet height and the contact angle out of the fringe number and the fringe radius in RIF from the geometric formulation. Furthermore, the ray tracing simulation is conducted using the custom-designed code. The geometric formulation and the ray tracing show excellent agreement with the experimental observation in the relation between the droplet height and the fringe number and the relation between the contact angle and the fringe radius. This study is remarkable as the droplet's dual profile cannot be easily observed with the existing techniques. However, the RIF technique can effectively verify the existence of a dual profile of the microdroplets in a simple setup. In this work, the RIF technique is successfully developed as a new optical diagnostic technique to determine the microdroplet features, such as the dual profile, the height, the contact angle, the inflection point, and the precursor film thickness, by simply measuring the RIF patterns on the far-field screen.
more »
« less
- Award ID(s):
- 2301973
- PAR ID:
- 10594022
- Publisher / Repository:
- American Institute of Physics
- Date Published:
- Journal Name:
- Journal of Applied Physics
- Volume:
- 135
- Issue:
- 20
- ISSN:
- 0021-8979
- Format(s):
- Medium: X
- Sponsoring Org:
- National Science Foundation
More Like this
-
-
Recently, reflection interference fringe (RIF) and transmission fringe (TIF) techniques have been introduced to investigate the origin of far-field interference fringe (IF) formation and to determine a droplet's contact angle and thickness by measuring the fringe radius. In this study, characteristics of the IF technique are analyzed based on the RIF and TIF by varying the schematics, such as configuration (transmission/reflection), the droplet's side (left-hand side/right-hand side), and the substrate types (flat/prism). The analysis also investigates the refraction effect at the droplet edge and the maximum incidence and contact angles. The schematic variation shows that the widest contact angle range can be measured in a transmission configuration with droplet's right-hand side, and that the fringe radius decreases with incidence angles on a prism substrate, consistent with the recent observation. Refraction at the droplet edge causes the fringe radius to increase or decrease depending on the degree of refraction. Based on the characteristics study, it is revealed that the IF technique can determine nanometer-scale thicknesses below 100 nm on droplets, corresponding to ultra-small contact angles of less than 0.01°, with an extended working distance of 3000 mm and an optimized incidence angle, assuming a spherical profile. This finding is significant, as it demonstrates that the nanoscale thickness can be determined in situ under ambient conditions using a simple optical configuration, without requiring a sophisticated setup, such as a microscope. It is anticipated that the IF technique can be combined with other nanoscale thickness measurement techniques to enhance its measurement reliability.more » « less
-
A recently reported vision ray metrology technique [Opt. Express29,43480(2021)OPEXFF1094-408710.1364/OE.443550] measures geometric wavefronts with high precision. This paper introduces a method to convert these wavefront data into height information, focusing on the impact of back surface flatness and telecentricity errors on measurement accuracy. Systematic errors from these factors significantly affect height measurements. Using ray trace simulations, we estimate reconstruction errors with various plano-concave and plano-convex elements. We also developed a calibration technique to mitigate telecentricity errors, achieving submicron accuracy in surface reconstruction. This study provides practical insights into vision ray metrology systems, highlighting validity limits, emphasizing the importance of calibration for larger samples, and establishing system alignment tolerances. The reported technique for the conversion of geometric wavefronts to surface topography employs a direct non-iterative ray-tracing-free method. It is ideally suited for reference-free metrology with application to freeform optics manufacturing.more » « less
-
null (Ed.)We study the wetting of a thin elastic filament floating on a fluid surface by a droplet of another, immiscible fluid. This quasi-2D experimental system is the lower-dimensional counterpart of the wetting and wrapping of a droplet by an elastic sheet. The simplicity of this system allows us to study the phenomenology of partial wetting and wrapping of the droplet by measuring angles of contact as a function of the elasticity of the filament, the applied tension and the curvature of the droplet. We find that a purely geometric theory gives a good description of the mechanical equilibria in the system. The estimates of applied tension and tension in the filament obey an elastic version of the Young–Laplace–Dupré relation. However, curvatures close to the contact line are not captured by the geometric theory, possibly because of 3D effects at the contact line. We also find that when a highly-bendable filament completely wraps the droplet, there is continuity of curvature at the droplet-filament interface, leading to seamless wrapping as observed in a 3D droplet.more » « less
-
Abstract Lasers have a wide range of manufacturing applications, one of which is the bending of metals. While there are multiple ways to induce bending in metals with lasers, this paper examines laser peen forming with femtosecond lasers on thin metals of 75-micrometer thickness perpendicular to the laser. The effects of multiple parameters, including laser energy, scan speed, scan pitch, and material preparation, on the bend angle of the metal are investigated. The bend angles are generated in both concave and convex directions, represented by positive and negative angles, respectively. While it is possible to create angles ranging from 0 to 90 degrees in the concave direction, the largest average convex angle found was only −26.2 degrees. The positive angles were created by high overlapping ratios and slow speeds. Furthermore, the concave angles were made by a smaller range of values than the convex angles, although this range could be expanded by higher laser energy. The positive angles also had a higher inconsistency than the negative angles, with an average standard deviation of 6.8 degrees versus an average of 2.6 degrees, respectively. The characterization of bending angles will allow for more accurate predictions, which will benefit traditional metal forming applications and more advanced applications such as origami structures with metal.more » « less
